CoChat

Viscoplastic Anand model for solder alloys and its application

Cheng, Z.N., Wang, G.Z., Chen, L., Wilde, J., Becker, K. · 2000 · Soldering & Surface Mount Technology

The DOI matches its Crossref record; 21 of the 22 references it cites were found in a registry or an index.

Abstract

A viscoplastic constitutive model, the Anand model, in which plasticity and creep are unified and described by the same set of flow and evolutionary relations, was applied to represent the inelastic deformation behavior for solder alloys. After conducting creep tests and constant strain rate tests, the material parameters for the Anand model of the Pb‐rich content solder 92.5Pb5Sn2.5Ag were determined from the experimental data using a nonlinear fitting method. The material parameters for 60Sn40Pb, 62Sn36Pb2Ag and 96.5Sn3.5Ag solders were fitted from the conventional model in the literature where plasticity and creep are artificially separated. Model simulations and verifications reveal that there is good agreement between the model predictions and experimental data. Some discussion on this unified model is also presented. This viscoplastic constitutive model for solder alloys possesses some advantages over the separated model. The achieved Anand model has been applied in finite element simulation of stress/strain responses in solder joints for chip component, thin quad flat pack and flip‐chip assembly. The simulation results are in good agreement with the results in the literature. It is concluded that the Anand model could be recommended as a useful material model for solder alloys and can be used in the finite element simulation of solder joint reliability in electronic packaging and surface mount technology.

Overview

Integrity signals

Registry

Crossref · 10.1108/09540910010331428

Cites

21 of 21 references verified0 citation errors · 0 not checkable

Statistics

Recomputing p-values needs the paper’s full text.

Verification

Claims the paper makes

This paper’s full text isn’t openly available, so its claims and self-check weren’t run. The registry and citation checks still apply.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Citations

Cites

Show all 21 references

Research works printed but not linked: 4

  1. Qian, Z. and Liu, S. (1997), “A unified viscoplastic constitutive model for tin‐lead solder joints”, in Advances in Electronic Packaging, ASME EEP, Vol. 19‐2, pp. 1599‐604.
  2. Solomon, H.D. (1986), “Creep, strain‐rate sensitivity and low cycle fatigue of 60/40 solder”, Brazing and Soldering, Vol. 11, pp. 68‐75.
  3. Veidt, M. (1998), “Viscoelastic tensile and shear properties of the 62wt%Sn‐36wt%Pb‐2wt%Ag solder alloy”, J. Materials Science, Vol. 33, pp. 1607‐10.
  4. Wang, G.Z., Fang, H.Y., Wang, C.Q. and Qian, Y.Y. (1997), “An experimental study of effects of solder joint geometry on thermal cycle life in SMT”, China Welding, Vol. 6 No. 1, pp. 67‐73.

Cited by

See all 151

Metadata

Authors
Cheng, Z. N., Wang, G. Z., Chen, L., Wilde, J., & Becker, K.
Affiliations
  • Shanghai Institute of Microsystem and Information Technology (CN)
  • University of Freiburg (DE)
  • TH Bingen University of Applied Sciences (DE)
Venue
Soldering & Surface Mount Technology
Publisher
Emerald
Published
2000-08-01
Volume
12
Issue
2
Pages
31-36
ISSN
0954-0911 (ISSN-L)
OpenAlex
W2003688086
Cited by
132
References
22
Citations by year
2026: 8 · 2025: 9 · 2024: 8 · 2023: 12 · 2022: 5 · 2021: 6 · 2019: 7 · 2018: 6 · 2017: 7 · 2016: 5 · 2014: 5 · 2013: 4 · 2012: 7
FWCI
2.59
Type
journal article
Language
en
Open access
closed
Licence
www.emerald.com/insight/site-policies (tdm)
Locations
Soldering and Surface Mount Technology (publishedVersion)
Topics
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Electronic Packaging and Soldering Technologies
  • Physical Sciences › Engineering › Biomedical Engineering › Elasticity and Material Modeling
  • Physical Sciences › Engineering › Mechanical Engineering › High Temperature Alloys and Creep
Keywords
Anand model, viscoplastic constitutive model, solder alloys, creep, plasticity, tin-lead solder, Sn-Ag solder, material parameter identification, solder joint reliability, flip-chip bonding, electronic packaging, surface mount technology

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Viscoplastic Anand model for solder alloys and its application. https://app.cochat.ai/papers/10.1108/09540910010331428
The paper
Cheng, Z. N., Wang, G. Z., Chen, L., Wilde, J., & Becker, K. (2000). Viscoplastic Anand model for solder alloys and its application. Soldering & Surface Mount Technology. https://doi.org/10.1108/09540910010331428

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.