The DOI matches its Crossref record.
An enhanced approach for implementing total productive maintenance in the manufacturing environment
Abstract
Many systems in use today are not performing as intended, nor are they cost effective in terms of their operation and support. Manufacturing systems, in particular, often operate at less than full capacity, productivity is low, and the costs of producing products are high. In dealing with the aspect of cost, experience has indicated that a large percentage of the total cost of doing business is due to maintenance‐ related activities in the factory; i.e. the costs associated with maintenance labour and materials and the cost due to production losses. Further, these costs are likely to increase even more in the future with the added complexities of factory equipment through the introduction of new technologies, automation, the use of robots, and so on. In response to maintenance and support problems in the typical factory environment, the Japanese introduced the concept of total productive maintenance (TPM), an integrated life cycle approach to factory maintenance and support. TPM methods and techniques have been successfully implemented in Japan through the past decade, and more recently in the USA. Inherent within the TPM concept are the aspects of enhancing the overall effectiveness (efficiency) of factory equipment, and providing an optimal group organizational approach in the accomplishment of system maintenance activities. Both the equipment and the organizational sides of the spectrum need to be addressed in fulfilling the objectives of TPM. It is believed that while many successes have been realized in structuring organizations to respond better to the maintenance challenge, very little progress has been made relative to the influence of equipment design for minimal maintenance and support (i.e. the incorporation of reliability, maintainability, and supportability characteristics in design). Briefly addresses this aspect of the problem, identifies some design analysis/evaluation tools that can be used, and recommends an approach for the continuous improvement of manufacturing systems in terms of operation and support.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Total productive maintenance: literature review and directions
Ahuja, I. P. S., & Khamba, J. S. (2008) · International Journal of Quality & Reliability Management · doi:10.1108/02656710810890890 · Cited by 574
Implementation of total productive maintenance: A case study
Chan, F. T. S., Lau, H. C. W., Ip, R. W. L., Chan, H. K., & Kong, S. (2005) · International Journal of Production Economics · doi:10.1016/j.ijpe.2003.10.021 · Cited by 392
Applying lean six sigma in a small engineering company – a model for change
Thomas, A., Barton, R., & Chuke‐Okafor, C. (2008) · Journal of Manufacturing Technology Management · doi:10.1108/17410380910925433 · Cited by 258
Metadata
- Authors
- Blanchard, B. S.
- Venue
- Journal of Quality in Maintenance Engineering
- Publisher
- Emerald
- Published
- 1997-06-01
- Volume
- 3
- Issue
- 2
- Pages
- 69-80
- ISSN
- 1355-2511 (ISSN-L)
- OpenAlex
- W1994890662
- Cited by
- 165
- References
- 0
- FWCI
- 8.59
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: An enhanced approach for implementing total productive maintenance in the manufacturing environment. https://app.cochat.ai/papers/10.1108/13552519710167692
- The paper
- Blanchard, B. S. (1997). An enhanced approach for implementing total productive maintenance in the manufacturing environment. Journal of Quality in Maintenance Engineering. https://doi.org/10.1108/13552519710167692
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.