The DOI matches its Crossref record; 11 of the 11 references it cites were found in a registry or an index.
Ductility of a Ti‐6Al‐4V alloy produced by selective laser melting of prealloyed powders
Abstract
Purpose: The aim of the paper is the study of the change in the mechanical properties (and in particular in ductility), with the microstructure, of a biomedical Ti‐6Al‐4V alloy produced by different variants of selective laser melting (SLM). Design/methodology/approach: Ti‐6Al‐4V alloy produced by different variants of SLM has been mechanically characterized through tensile testing. Its microstructure has been investigated by optical observation after etching and by X‐ray diffraction analysis. Findings: SLM applied to Ti‐6Al‐4V alloy produces a material with a martensitic microstructure. Some microcracks, due the effect of incomplete homologous wetting and residual stresses produced by the large solidification undercooling of the melt pool, are observable in the matrix. Owing to the microstructure, the tensile strength of the additive manufactured parts is higher than the strength of hot worked parts, whereas the ductility is lower. A pre‐heating of the powder bed is effective in assisting remelting and reducing residual stresses, but ductility does not increase significantly, since the microstructure remains martensitic. A post‐building heat treatment causes the transformation of the metastable martensite in a biphasic a‐b matrix, with a morphology that depends on the heat treatment. This results in an increase in ductility and a reduction in strength values. Originality/value: The study evidenced how it is possible to obtain a fully dense material and make the martensite transform in Ti‐6Al‐4V alloy through the variation of the SLM process. The stabilization of the microstructure also results in an improvement of the ductility.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Titanium and Titanium Alloys: Fundamentals and Applications
(2003) · Wiley eBooks · doi:10.1002/3527602119 · Cited by 3,108
Selective laser melting of iron-based powder
Kruth, J. P., Froyen, L., Van Vaerenbergh, J., Mercelis, P., Rombouts, M., & Lauwers, B. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2003.11.051 · Cited by 1,550
(2001) · Alloying · doi:10.31399/asm.tb.aub.t61170417 · Cited by 1,209
Physical Metallurgy of Titanium Alloys
Joshi, V. A. (2006) · CRC Press eBooks · doi:10.1201/9781420006063-8 · Cited by 628
Hollander, D. A., von Walter, M., Wirtz, T., Sellei, R., Schmidt-Rohlfing, B., Paar, O., & Erli, H.-J. (2006) · Biomaterials · doi:10.1016/j.biomaterials.2005.07.041 · Cited by 482
Physical Aspects of Process Control in Selective Laser Sintering of Metals
Das, S. (2003) · Advanced Engineering Materials · doi:10.1002/adem.200310099 · Cited by 434
Simchi, A., & Pohl, H. (2003) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(03)00341-1 · Cited by 377
Facchini, L., Magalini, E., Robotti, P., & Molinari, A. (2009) · Rapid Prototyping Journal · doi:10.1108/13552540910960262 · Cited by 290
Self-citationInfluence of tempering temperature and time on the α′-Ti-6Al-4V martensite
Gil, F. X., Rius, D. R., & Planell, J. A. (1996) · Journal of Alloys and Compounds · doi:10.1016/0925-8388(95)02057-8 · Cited by 230
Characterization of H13 steel produced via electron beam melting
Cormier, D., Harrysson, O., & West, H. (2004) · Rapid Prototyping Journal · doi:10.1108/13552540410512516 · Cited by 227
Cited by
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Laser additive manufacturing of metallic components: materials, processes and mechanisms
Gu, D. D., Meiners, W., Wissenbach, K., & Poprawe, R. (2012) · International Materials Reviews · doi:10.1179/1743280411y.0000000014 · Cited by 3,197
Self-citationAdditive manufacturing of Ti6Al4V alloy: A review
Liu, S., & Shin, Y. C. (2019) · Materials & Design · doi:10.1016/j.matdes.2018.107552 · Cited by 2,472
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.07.022 · Cited by 1,896
Metadata
- Authors
- Facchini, L., Magalini, E., Robotti, P., Molinari, A., Höges, S., & Wissenbach, K.
- Venue
- Rapid Prototyping Journal
- Publisher
- Emerald
- Published
- 2010-10-05
- Volume
- 16
- Issue
- 6
- Pages
- 450-459
- ISSN
- 1355-2546 (ISSN-L)
- OpenAlex
- W2065589878
- Cited by
- 512
- References
- 11
- FWCI
- 15.82
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Ductility of a Ti‐6Al‐4V alloy produced by selective laser melting of prealloyed powders. https://app.cochat.ai/papers/10.1108/13552541011083371
- The paper
- Facchini, L., Magalini, E., Robotti, P., Molinari, A., Höges, S., & Wissenbach, K. (2010). Ductility of a Ti‐6Al‐4V alloy produced by selective laser melting of prealloyed powders. Rapid Prototyping Journal. https://doi.org/10.1108/13552541011083371
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.