The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Fatigue analysis of FDM materials
Abstract
Purpose: The purpose of this paper is to determine the effects of fatigue on fused deposition modeling rapid prototyped acrylonitrile butadiene styrene (ABS) materials. Design/methodology/approach: FDM dog bones based on UNI EN ISO 527‐1 (1997) were tested at 100, 80, 60, and 40 per cent nominal values of the ultimate stress for nine different print orientations. The samples were cyclically stressed in a tensile tester at 25.4 mm/min (extension) and relaxed at 12.7 mm/min. Findings: Although FDM ABS has a tensile strength that is relatively close to that of the bulk material, up to 80 percent, its ability to absorb energy before fracture has a tremendous amount of room for improvement. FDM ABSplus (P430) material properties are noticeably more isotropic than the predecessor, ABS (P400). The ABSplus fractures in the order of thousands of cycles at 40 percent of ultimate stress load, while the ABS exhibits the similar cycle limits at 60 percent of its ultimate stress load. Practical implications: FDM ABS parts are limited in fatigue characteristics even though they exhibit similar ultimate stress limits as with bulk materials, warranting further research in improving FDM parts expected to experience cyclical loads. Originality/value: This paper adds knowledge to the limited fatigue data in literature for FDM ABS. It investigated the load cyclic data of fused deposition modeled ABS through analyzing its cycle‐by‐cycle strain energy, providing another means of identifying the fatigue characteristics of materials.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Hiss, R., Hobeika, S., Lynn, C., & Strobl, G. (1999) · Macromolecules · doi:10.1021/ma981776b · Cited by 540
Effect of chain entanglements on plastic deformation behavior of linear polyethylene
Bartczak, Z. (2005) · Macromolecules · doi:10.1021/ma050815y · Cited by 116
Cited by
Wu, W., Geng, P., Li, G., Zhao, D., Zhang, H., & Zhao, J. (2015) · Materials · doi:10.3390/ma8095271 · Cited by 881
Shanmugam, V., Das, O., Babu, K., Marimuthu, U., Veerasimman, A., Johnson, D. J., Neisiany, R. E., Hedenqvist, M. S., Ramakrishna, S., & Berto, F. (2021) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2020.106007 · Cited by 538
Mohan, N., Senthil, P., Vinodh, S., & Jayanth, N. (2017) · Virtual and Physical Prototyping · doi:10.1080/17452759.2016.1274490 · Cited by 457
Process–Structure–Properties in Polymer Additive Manufacturing via Material Extrusion: A Review
Goh, G. D., Yap, Y. L., Tan, H. K. J., Sing, S. L., Goh, G. L., & Yeong, W. Y. (2020) · Critical Reviews in Solid State and Materials Sciences · doi:10.1080/10408436.2018.1549977 · Cited by 429
Additive manufacturing in unmanned aerial vehicles (UAVs): Challenges and potential
Goh, G. D., Agarwala, S., Goh, G. L., Dikshit, V., Sing, S. L., & Yeong, W. Y. (2017) · Aerospace Science and Technology · doi:10.1016/j.ast.2016.12.019 · Cited by 413
Metadata
- Authors
- Lee, J., & Huang, A.
- Venue
- Rapid Prototyping Journal
- Publisher
- Emerald
- Published
- 2013-06-07
- Volume
- 19
- Issue
- 4
- Pages
- 291-299
- ISSN
- 1355-2546 (ISSN-L)
- OpenAlex
- W2020842342
- Cited by
- 161
- References
- 2
- FWCI
- 14.52
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Fatigue analysis of FDM materials. https://app.cochat.ai/papers/10.1108/13552541311323290
- The paper
- Lee, J., & Huang, A. (2013). Fatigue analysis of FDM materials. Rapid Prototyping Journal. https://doi.org/10.1108/13552541311323290
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.