Investigation into train positioning systems for saving energy with optimised train trajectories
Open accessThe DOI matches its Crossref record; 38 of the 39 references it cites were found in a registry or an index.
Abstract
One approach to reduce energy consumption in railway systems is to implement optimised train trajectories. These are speed profiles that reduce energy consumption without foregoing customer comfort or running times. This is achieved by avoiding unnecessary braking and running at reduced speed whilst maintaining planned arrival times. An optimised train trajectory can be realised using a driver advisory system (DAS). The optimal train trajectory approach needs a variety of input data, such as the train's position, speed, direction, gradient, maximum speed, dwell time, and station locations. Many studies assume the availability of a very accurate train position in real time. However, providing and using high precision positioning data is not always the most cost-effective solution. The aim of this research is to investigate the use of appropriate positioning systems, with regard to their performance and cost specifications, with optimised trajectories. This paper first presents a single train trajectory optimisation to minimise overall energy consumption. It then explores how errors in train position data affect the total consumed energy, with regard to the tractive force due to gradient when following the optimised trajectory. A genetic algorithm is used to optimise the train speed profile. The results from simulation indicate that a basic GPS system for specifying train position is sufficient to save energy via an optimised train trajectory. The authors investigate the effect of error in positioning data, to guarantee the reliability of employing the optimised solution for saving energy whilst maintaining an acceptable journey time.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The results obtained following the advice generated by the DAS when updating the system every meter, showed that the optimized trajectory could save energy up to around 25%.”
From Towards the Internet of Smart Trains: A Review on Industrial IoT-Connected Railways (2017) · cites this paper as [138]
In the citing paper
“However, a train positioning system error under 100 m increases the energy consumption by less than 0.3%, while an error under 500 m increases it by less than 1.5% for uphill lines; and 1.3% and 5.2%, respectively, for a downhill line.”
From Towards the Internet of Smart Trains: A Review on Industrial IoT-Connected Railways (2017) · cites this paper as [138]
Citations
Cites
Energy-efficient operation of rail vehicles
Liu, R. (., & Golovitcher, I. M. (2003) · Transportation Research Part A: Policy and Practice · doi:10.1016/j.tra.2003.07.001 · Cited by 571 · cited 1×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodSingle-Train Trajectory Optimization
Lu, S., Hillmansen, S., Ho, T. K., & Roberts, C. (2013) · IEEE Transactions on Intelligent Transportation Systems · doi:10.1109/tits.2012.2234118 · Cited by 334 · cited 4×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
BackgroundMethodSelf-citationOptimising train movements through coastcontrolusing genetic algorithms
Chang, C. S., & Sim, S. S. (1997) · IEE Proceedings - Electric Power Applications · doi:10.1049/ip-epa:19970797 · Cited by 327 · cited 1×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodOptimal driving strategy for traction energy saving on DC suburban railways
Bocharnikov, Y. V., Tobias, A. M., Roberts, C., Hillmansen, S., & Goodman, C. J. (2007) · IET Electric Power Applications · doi:10.1049/iet-epa:20070005 · Cited by 248 · cited 9×
“Consequently, the train speed is decreased gradually based on resistance to motion and the force due to the gradient [3][29].”
BackgroundMethodSelf-citationFuzzy Modeling and Genetic Algorithms for Data Mining and Exploration
(2005) · Elsevier eBooks · doi:10.1016/b978-0-12-194275-5.x5000-2 · Cited by 212 · cited 1×
“As recommended by [48], the number of chromosomes should be at least five times the number of genomes, therefore, the population has been chosen to consist of 16 chromosomes.”
BackgroundOptimizing trains movement on a railway network
Yang, L., Li, K., Gao, Z., & Li, X. (2011) · Omega · doi:10.1016/j.omega.2011.12.001 · Cited by 159 · cited 1×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodAn assessment of available measures to reduce traction energy use in railway networks
Douglas, H., Roberts, C., Hillmansen, S., & Schmid, F. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2015.10.053 · Cited by 143 · cited 5×
“Consequently, the train speed is decreased gradually based on resistance to motion and the force due to the gradient [3][29].”
BackgroundMethodSelf-citationDomínguez, M., Fernández-Cardador, A., Cucala, A. P., Gonsalves, T., & Fernández-Rodríguez, A. (2014) · Engineering Applications of Artificial Intelligence · doi:10.1016/j.engappai.2013.12.015 · Cited by 141 · cited 2×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodCoast control for mass rapid transit railways with searching methods
Wong, K. K., & Ho, T. K. (2004) · IEE Proceedings - Electric Power Applications · doi:10.1049/ip-epa:20040346 · Cited by 136 · cited 1×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodAcikbas, S., & Söylemez, M. T. (2008) · IET Electric Power Applications · doi:10.1049/iet-epa:20070381 · Cited by 134 · cited 1×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodA Multiple Train Trajectory Optimization to Minimize Energy Consumption and Delay
Zhao, N., Roberts, C., Hillmansen, S., & Nicholson, G. L. (2015) · IEEE Transactions on Intelligent Transportation Systems · doi:10.1109/tits.2014.2388356 · Cited by 124 · cited 3×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodSelf-citationCucala, A. P., Fernández-Cardador, A., Sicre, C., & Domínguez, M. (2012) · Engineering Applications of Artificial Intelligence · doi:10.1016/j.engappai.2012.02.006 · Cited by 114
Dynamic coast control of train movement with genetic algorithm
WONG, K. K. F., & Ho, T. K. (2004) · International Journal of Systems Science · doi:10.1080/00207720412331203633 · Cited by 114 · cited 4×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
BackgroundMethodInfluentialHwang, H. (1998) · IEEE Transactions on Systems Man and Cybernetics - Part A Systems and Humans · doi:10.1109/3468.725350 · Cited by 112 · cited 1×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodReduction of train and net energy consumption using genetic algorithms for trajectory optimisation
Bocharnikov, Y. V., Tobias, A. M., & Roberts, C. (2010) · IET Conference on Railway Traction Systems (RTS) · doi:10.1049/ic.2010.0038 · Cited by 96 · cited 4×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
BackgroundMethodSelf-citationAn optimal automatic train operation (ATO) control using genetic algorithms (GA)
Han, S. H., Byen, Y. S., Baek, J., An, T. K., Lee, S. G., & Park, H. J. (2003) · IEEE Region 10 Conference (TENCON) · doi:10.1109/tencon.1999.818425 · Cited by 91 · cited 1×
“An optimised trajectory for a specific route, vehicle and timetable can be achieved by selecting the best points at which to change between traction, coasting and braking modes using a genetic algorithm.”
MethodA Power-Management Strategy for Multiple-Unit Railroad Vehicles
Lu, S., Hillmansen, S., & Roberts, C. (2010) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2010.2093911 · Cited by 84 · cited 4×
“Fgrad is the force due to the gradient, which can be calculated by [3][42]:”
BackgroundMethodSelf-citationOptimization of train-speed trajectory and control for mass rapid transit systems
Ke, B., Lin, C., & Lai, C.-W. (2011) · Control Engineering Practice · doi:10.1016/j.conengprac.2011.03.003 · Cited by 83 · cited 1×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodA Genetic Algorithm for Railway Scheduling Problems
Tormos, P., Lova, A., Barber, F., Ingolotti, L., Abril, M. A., & Salido, M. Á. (2008) · Studies in computational intelligence · doi:10.1007/978-3-540-78985-7_10 · Cited by 79 · cited 1×
“The remainder of the next generation is set using tournament selection, as suggested by [49].”
MethodEnergy storage devices in hybrid railway vehicles: A kinematic analysis
Hillmansen, S., & Roberts, C. (2007) · Proceedings of the Institution of Mechanical Engineers Part F Journal of Rail and Rapid Transit · doi:10.1243/09544097jrrt99 · Cited by 78 · cited 2×
“To determine the coasting and braking points, the forward and backward calculation of speed profile is needed [12][43][46].”
MethodSelf-citationModeling and optimizing energy‐efficient manual driving on high‐speed lines
Sicre, C., Cucala, A. P., Fernández-Cardador, A., & Łukaszewicz, P. (2012) · IEEJ Transactions on Electrical and Electronic Engineering · doi:10.1002/tee.21782 · Cited by 65
Railway driver advice systems: Evaluation of methods, tools and systems
Panou, K., Tzieropoulos, P., & Émery, D. (2013) · Journal of Rail Transport Planning & Management · doi:10.1016/j.jrtpm.2013.10.005 · Cited by 54 · cited 6×
“Moreover, with both ERTMS/ETCS and signalling detection techniques, the train speed can be estimated by inference, from the time between successive recording points [23][24].”
BackgroundMethodInfluentialA map matching approach for train positioning. II. Application and experimentation
Saab, S. S. (2000) · IEEE Transactions on Vehicular Technology · doi:10.1109/25.832979 · Cited by 43 · cited 1×
“Generally, a basic GPS signal provides absolute accuracy of 60-100 metres [26][27].”
BackgroundA Review Study on Traction Energy Saving of Rail Transport
Feng, X., Zhang, H., Ding, Y., Liu, Z., Peng, H., & Xu, B. (2013) · Discrete Dynamics in Nature and Society · doi:10.1155/2013/156548 · Cited by 43 · cited 1×
“Furthermore, energy efficiency in railway systems has become a global concern and it is a subject being explored with the purpose of reducing energy consumption as a result of rising energy prices as well as environmental concerns [1][2].”
BackgroundDesign of optimal coasting speed for saving social cost in Mass Rapid Transit systems
Chuang, H.-J., Chen, C., Lin, C., Hsieh, C.-H., & Ho, C.-Y. (2008) · IEEE International Conference on Electric Utility Deregulation, Restructuring and Power Technologies · doi:10.1109/drpt.2008.4523892 · Cited by 38 · cited 1×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodHydrogen as an energy carrier for railway traction
Hoffrichter, A. (2013) · University of Birmingham Institutional Research Archive (University of Birmingham) · Cited by 37
Coast control of train movement with genetic algorithm
Wong, K. K., & Ho, T. K. (2004) · IEEE Congress on Evolutionary Computation (CEC) · doi:10.1109/cec.2003.1299816 · Cited by 31 · cited 1×
“To find the optimum train trajectories, a number of search methods have been used including: genetic algorithms [3][4][5][6][7][8][9][10][11][12]; particle swarm optimisation [13]; a direct searching method [14][15]; artificial neural networks (ANN) [16][17]; a combination of ANN and genetic algorithm techniques [18];…”
MethodZhao, N., Roberts, C., & Hillmansen, S. (2012) · Proceedings of the Institution of Mechanical Engineers Part F Journal of Rail and Rapid Transit · doi:10.1177/0954409712468231 · Cited by 31 · cited 4×
“In general, a speed profile is composed of three modes [2][19][34][35][39]: traction mode, coasting mode and braking mode, as illustrated in Fig.”
BackgroundMethodSelf-citationDesign of Optimal Coasting Speed for MRT Systems Using ANN Models
Chuang, H.-J., Chen, C., Lin, C., Hsieh, C.-H., & Ho, C.-Y. (2009) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2009.2031898 · Cited by 30
A GA-based Algorithm for Creating an Energy-Optimum Train Speed Trajectory
Kang, M.-H. (2011) · Journal of International Council on Electrical Engineering · doi:10.5370/jicee.2011.1.2.123 · Cited by 29 · cited 2×
“For this experiment, the following data are used: Class 375 EMU; the maximum line speed is 130km/h; the line length is 20km; the train movement starts from position zero and stops at 20 km; plain line sections with no stations; the train runs without regenerative braking [3][46] and the distance of the calculation ste…”
MethodOptimization Method of Energy Saving Train Operation for Railway Network
Fu, Y., Gao, Z., & Li, K. (2009) · Journal of Transportation Systems Engineering and Information Technology · doi:10.1016/s1570-6672(08)60074-4 · Cited by 23 · cited 2×
“In railway systems, the main criteria for an optimised train trajectory is often a trade-off between the energy consumed and journey time, as well as the comfort of passengers [4][6][9][29][30].”
BackgroundEuropean Rail Traffic Management System – An Overview
Abed, S. K. (2010) · Iraqi Journal for Electrical And Electronic Engineering · doi:10.33762/eeej.2010.54890 · Cited by 23 · cited 1×
“Guiding the train driver can be achieved by installing wayside coasting signs or by dynamically displaying the optimised speed requirement in-cab via the driver-machine interface (DMI) of a DAS [31].”
MethodMethod for validating the train motion equations used for passenger rail vehicle simulation
Douglas, H., Weston, P., Kirkwood, D., Hillmansen, S., & Roberts, C. (2016) · Proceedings of the Institution of Mechanical Engineers Part F Journal of Rail and Rapid Transit · doi:10.1177/0954409716631784 · Cited by 23 · cited 1×
“The energy E to realise that speed profile can be determined by [47]:”
BackgroundSelf-citationDurazo-Cardenas, I., Starr, A. G., Tsourdos, A., Bevilacqua, M. T., & Morineau, J. (2014) · Procedia CIRP · doi:10.1016/j.procir.2014.07.002 · Cited by 22 · cited 1×
“Differential GPS (D-GPS) is used to enhance positional accuracy, typically to within 2-3 metres in rail applications [28].”
MethodTrain trajectory optimisation of ATO systems for metro lines
Zhao, N., Roberts, C., Hillmansen, S., Western, P., Chen, L., Tian, Z., Xin, T., & Su, S. (2014) · IEEE International Conference on Intelligent Transportation Systems (ITSC) · doi:10.1109/itsc.2014.6957953 · Cited by 21 · cited 4×
“In general, a speed profile is composed of three modes [2][19][34][35][39]: traction mode, coasting mode and braking mode, as illustrated in Fig.”
BackgroundMethodSelf-citationHu, H., Li, K., & Xu, X. (2013) · 西南交通大学学报:英文版 · doi:10.1007/s40534-013-0003-1 · Cited by 19 · cited 1×
“To achieve the advised speed, which is based on train positioning system (with error), the driver will adjust the train power until realising the target speed.”
BackgroundCoasting boards vs optimal control
Coleman, D. C., Howlett, P., Pudney, P. J., Vu, X., & Yee, R. (2010) · IET Conference on Railway Traction Systems (RTS) · doi:10.1049/ic.2010.0020 · Cited by 13
A simple in-cab schedule advisory system to save energy and improve on-time performance
Johnson, P., & Brown, S. (2010) · IET Conference on Railway Traction Systems (RTS) · doi:10.1049/ic.2010.0021 · Cited by 10 · cited 3×
“In general, a speed profile is composed of three modes [2][19][34][35][39]: traction mode, coasting mode and braking mode, as illustrated in Fig.”
BackgroundMethod
Research works printed but not linked: 8
- 2012, The rail technical strategy 2012 (RTS 2012)
- driver, 0, GB operational concept connected driver advisory system (C-DAS)
- mitchell, 2012, The sustainable railway use of advisory systems for energy savings
- jin, 2009, Driver Advisory Information for Energy Management and Regulation, 1, 1
- mohan, 2014, Next generation train positioning systems
- 10.1016/j.jrtpm.2013.10.005 · DOI
- douglas, 2015, Method for validating the train motion equations used for passenger rail vehicle simulation, 0, 1
- de cuadra, 1996, Energy-saving automatic optimization of train speed commands using direct search techniques, The 1996 5 th International Conference on Computer Aided Design Manufacture and Operation in the Railway and other Advanced Mass Transit Systems Part 1(of 2)
Cited by
Towards the Internet of Smart Trains: A Review on Industrial IoT-Connected Railways
Fraga-Lamas, P., Fernández-Caramés, T., & Castedo, L. (2017) · Sensors · doi:10.3390/s17061457 · Cited by 267
“In [138] it is proposed a genetic algorithm for optimizing the train speed profile.”
BackgroundMethodAdaptive Partial Train Speed Trajectory Optimization
Tan, Z., Lu, S., Bao, K., Zhang, S., Wu, C., Yang, J., & Xue, F. (2018) · Energies · doi:10.3390/en11123302 · Cited by 31
“The authors in [43] investigated the influence of the error of train positioning in optimal speed trajectory obtained using a GA.”
MethodEnergy optimization in freight train operations: Algorithmic development and testing
Aredah, A., Fadhloun, K., & Rakha, H. A. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.123111 · Cited by 19
Hamid, H. A., Nicholson, G. L., & Roberts, C. (2020) · IET Intelligent Transport Systems · doi:10.1049/iet-its.2019.0503 · Cited by 14
Self-citationNai, W., Chen, Y., Zhang, X., Lei, X., & Dong, D. (2017) · IEEE International Conference on Computer and Communications (ICCC) · doi:10.1109/compcomm.2017.8322674 · Cited by 5
“(2016) have proposed a Global Navigation Satellite System (GNSS) based train positioning system which may not help enhancing the positioning accuracy much, but could optimize the train running trajectories [5]; specific for medium-low speed transit system, X.”
Background
Metadata
- Authors
- Hamid, H. A., Nicholson, G. L., Douglas, H., Zhao, N., & Roberts, C.
- Affiliations
- University of Birmingham (GB)
- Venue
- 2016 IEEE International Conference on Intelligent Rail Transportation (ICIRT)
- Publisher
- IEEE
- Published
- 2016-08
- Pages
- 460-468
- OpenAlex
- W2528455006
- Cited by
- 13
- References
- 39
- Citations by year
- 2024: 1 · 2023: 2 · 2021: 1 · 2020: 2 · 2019: 1 · 2018: 4 · 2017: 2
- FWCI
- 3.88
- Type
- conference paper
- Language
- en
- Open access
- Licence
- cc-by
- Locations
- IEEE International Conference on Intelligent Rail Transportation (ICIRT) (publishedVersion)
- Durham Research Online (Durham University) (submittedVersion, cc-by)
- University of Birmingham Research Portal (University of Birmingham) (submittedVersion)
- Topics
- Social Sciences › Transportation › Railway Systems and Energy Efficiency
- Physical Sciences › Engineering › Mechanical Engineering › Railway Engineering and Dynamics
- Physical Sciences › Engineering › Control and Systems Engineering › Traffic control and management
- Keywords
- train energy consumption, train speed profiles, GPS, driver advisory systems, genetic algorithm, railway energy efficiency, travel time
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.