Student or educator? Sign up with your school email and get 6 months of Pro free.
Cited by 165

The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.

Development of epoxy/BN composites with high thermal conductivity and sufficient dielectric breakdown strength partI - sample preparations and thermal conductivity

Wang, Zengbin, Iizuka, Tomonori, Kozako, Masahiro, Ohki, Yoshimichi, Tanaka, Toshikatsu · 2011 · IEEE Transactions on Dielectrics and Electrical Insulation

Abstract

The aim of this research is to find a way to achieve the epoxy composites with both high thermal conductivity and acceptable dielectric breakdown (BD) strength. As high thermal conductivity, low permittivity and low thermal expansion coefficient of filler can endow composite with higher thermal conductivity, higher BD strength and lower thermal expansion coefficient respectively, BN (boron nitride) with high thermal conductivity, low permittivity and low thermal expansion coefficient was adopted as main filler in the research. Thermal conductivity was investigated in this part. The BD strength of samples will be discussed in Part II. Neat epoxy and other 25 kinds of epoxy/BN composites were prepared by a hot press method. Most of BN fillers were surface modified with silane coupling agent through ethanol/water reflux method to improve thermal conductivity. The values of 2.91 W/m·K, 3.95 W/m·K and 10.1 W/m·K as thermal conductivity were obtained for the composites that was single-loaded with h-BN(hexagonal boron nitride), c-BN (cubic boron nitride) or conglomerated h-BN, respectively. They were further improved to 5.26 W/m·K, 5.94 W/m·K and 12.3 W/m·K, respectively, by adding extra smaller A1N (aluminum nitride) to fill the voids in sample. Thermal conductivity of samples changes with the ratio of c-BN and h-BN when c-BN and h-BN were co-loaded. A value of 5.74 W/m·K as maximum was obtained at their ratio of 1 to 1 when total filler content is 80 wt%. A much higher value of 7.69 W/m·K was obtained by adding extra AIN. From the experiment data, it is concluded that the filler orientation in vertical direction of sample surface and the decrease of voids in sample are very important to obtain high thermal conductivity, and that the filler surface modification is also necessary to improve thermal conductivity especially for epoxy/c-BN composites, and addition of nano silica in small amount can also increase thermal conductivity if sample is prepared appropriately.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1109/tdei.2011.6118634

Cites

1 of 1 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cited by

See all 165

Metadata

Authors
Wang, Z., Iizuka, T., Kozako, M., Ohki, Y., & Tanaka, T.
Venue
IEEE Transactions on Dielectrics and Electrical Insulation
Published
2011-12
Volume
18
Issue
6
Pages
1963-1972
ISSN
  • 1070-9878 (ISSN-L)
  • 1558-4135
OpenAlex
W2042091172
Cited by
165
References
1
FWCI
3.10
Type
journal article
Language
en
Open access
closed

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Development of epoxy/BN composites with high thermal conductivity and sufficient dielectric breakdown strength partI - sample preparations and thermal conductivity. https://app.cochat.ai/papers/10.1109/tdei.2011.6118634
The paper
Wang, Z., Iizuka, T., Kozako, M., Ohki, Y., & Tanaka, T. (2011). Development of epoxy/BN composites with high thermal conductivity and sufficient dielectric breakdown strength partI - sample preparations and thermal conductivity. IEEE Transactions on Dielectrics and Electrical Insulation. https://doi.org/10.1109/tdei.2011.6118634

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.