The DOI matches its Crossref record; 9 of the 9 references it cites were found in a registry or an index.
Machining Process Monitoring and Control: The State-of-the-Art
Abstract
Research in automating the process level of machining operations has been conducted, in both academia and industry, over the past few decades. This work is motivated by a strong belief that research in this area will provide increased productivity, improved part quality, reduced costs, and relaxed machine design constraints. The basis for this belief is two-fold. First, machining process automation can be applied to both large batch production environments and small batch jobs. Second, process automation can autonomously tune machine parameters (feed, speed, depth of cut, etc.) on-line and off-line to substantially increase the machine tool’s performance in terms of part tolerances and surface finish, operation cycle time, etc. Process automation holds the promise of bridging the gap between product design and process planning, while reaching beyond the capability of a human operator. The success of manufacturing process automation hinges primarily on the effectiveness of the process monitoring and control systems. This paper discusses the evolution of machining process monitoring and control technologies and conducts an in-depth review of the state-of-the-art of these technologies over the past decade. The research in each area is highlighted with experimental and simulation examples. Open architecture software platforms that provide the means to implement process monitoring and control systems are also reviewed. The impact, industrial realization, and future trends of machining process monitoring and control technologies are also discussed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Analytical Prediction of Stability Lobes in Milling
Altıntaş, Y., & Budak, E. (1995) · CIRP Annals · doi:10.1016/s0007-8506(07)62342-7 · Cited by 1,955
Budak, E., & Altıntaş, Y. (1998) · Journal of Dynamic Systems Measurement and Control · doi:10.1115/1.2801318 · Cited by 366
Efficient Simulation Programs for Chatter in Milling
Smith, S., & Tlusty, J. (1993) · CIRP Annals · doi:10.1016/s0007-8506(07)62486-x · Cited by 266
Landers, R. G., Min, B.-K., & Koren, Y. (2001) · CIRP Annals · doi:10.1016/s0007-8506(07)62120-9 · Cited by 223
Self-citationAzouzi, R., & Guillot, M. (1997) · International Journal of Machine Tools and Manufacture · doi:10.1016/s0890-6955(97)00013-8 · Cited by 195
Tool Wear Detection Using Time Series Analysis of Acoustic Emission
Liang, S. Y., & Dornfeld, D. A. (1989) · Journal of Engineering for Industry · doi:10.1115/1.3188750 · Cited by 186
Self-citationChoudhury, S. K., & Bartarya, G. (2003) · International Journal of Machine Tools and Manufacture · doi:10.1016/s0890-6955(02)00166-9 · Cited by 133
Control of tolerances in turning by predictive control with neural networks
Warnecke, G., & Kluge, R. (1998) · Journal of Intelligent Manufacturing · doi:10.1023/a:1008918606594 · Cited by 26
A systems theory approach to modelling of cutting temperature with experimental identification
D’Errico, G. E. (1997) · International Journal of Machine Tools and Manufacture · doi:10.1016/s0890-6955(96)00053-3 · Cited by 14
Cited by
Wavelet analysis of sensor signals for tool condition monitoring: A review and some new results
Zhu, K., Wong, Y. S., & Hong, G. S. (2009) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2009.02.003 · Cited by 406
High-sensitivity acoustic sensors from nanofibre webs
Lang, C., Fang, J., Shao, H., Ding, X., & Lin, T. (2016) · Nature Communications · doi:10.1038/ncomms11108 · Cited by 395
Werschmoeller, D., Li, X., & Ehmann, K. (2012) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4007621 · Cited by 32
Metadata
- Authors
- Liang, S. Y., Hecker, R. L., & Landers, R. G.
- Venue
- Journal of Manufacturing Science and Engineering
- Publisher
- ASME International
- Published
- 2004-05-01
- Volume
- 126
- Issue
- 2
- Pages
- 297-310
- ISSN
- 1087-1357 (ISSN-L)
- 1528-8935
- OpenAlex
- W2031341655
- Cited by
- 338
- References
- 9
- FWCI
- 34.76
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Machining Process Monitoring and Control: The State-of-the-Art. https://app.cochat.ai/papers/10.1115/1.1707035
- The paper
- Liang, S. Y., Hecker, R. L., & Landers, R. G. (2004). Machining Process Monitoring and Control: The State-of-the-Art. Journal of Manufacturing Science and Engineering. https://doi.org/10.1115/1.1707035
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.