The DOI matches its Crossref record; 18 of the 18 references it cites were found in a registry or an index.
Topology Optimization, Additive Layer Manufacturing, and Experimental Testing of an Air-Cooled Heat Sink
Abstract
Topology optimization of an air-cooled heat sink considering heat conduction plus side-surface convection is presented. The optimization formulation is explained along with multiple design examples. A postprocessing procedure is described to synthesize manifold or “water-tight” solid model computer-aided design (CAD) geometry from three-dimensional (3D) point-cloud data extracted from the optimization result. Using this process, a heat sink is optimized for confined jet impingement air cooling. A prototype structure is fabricated out of AlSi12 using additive layer manufacturing (ALM). The heat transfer and fluid flow performance of the optimized heat sink are experimentally evaluated, and the results are compared with benchmark plate and pin-fin heat sink geometries that are conventionally machined out of aluminum and copper. In two separate test cases, the experimental results indicate that the optimized ALM heat sink design has a higher coefficient of performance (COP) relative to the benchmark heat sink designs.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Generating optimal topologies in structural design using a homogenization method
Bendsøe, M. P., & Kikuchi, N. (1988) · Computer Methods in Applied Mechanics and Engineering · doi:10.1016/0045-7825(88)90086-2 · Cited by 7,467
The method of moving asymptotes—a new method for structural optimization
Svanberg, K. (1987) · International Journal for Numerical Methods in Engineering · doi:10.1002/nme.1620240207 · Cited by 5,573
(2011) · Introduction to Thermal and Fluid Engineering · doi:10.1201/b12301-22 · Cited by 4,217
Bendsøe, M. P., & Sigmund, O. (2004) · Springer eBooks · doi:10.1007/978-3-662-05086-6 · Cited by 1,727
Fundamentals of Microsystems Packaging
Tummala, R. (2001) · Cited by 817
Topology Optimization for Additive Manufacturing
Brackett, D., Ashcroft, I., & Hague, R. (2011) · doi:10.26153/tsw/15300 · Cited by 347
Development of heat sink device by using topology optimization
Koga, A. A., Lopes, E. C. C., Villa Nova, H. F., Lima, C. R. D., & Silva, E. C. N. (2013) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2013.05.007 · Cited by 320
Heaviside projection based topology optimization by a PDE-filtered scalar function
Kawamoto, A., MATSUMORI, T., Yamasaki, S., Nomura, T., Kondoh, T., & Nishiwaki, S. (2010) · Structural and Multidisciplinary Optimization · doi:10.1007/s00158-010-0562-2 · Cited by 308
Topological design of heat dissipating structure with forced convective heat transfer
Yoon, G. H. (2010) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-010-0328-1 · Cited by 272
Gaynor, A. T., Meisel, N. A., Williams, C. B., & Guest, J. K. (2014) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4028439 · Cited by 271
Cited by
Material-structure-performance integrated laser-metal additive manufacturing
Gu, D., Shi, X., Poprawe, R., Bourell, D. L., Setchi, R., & Zhu, J. (2021) · Science · doi:10.1126/science.abg1487 · Cited by 1,703
Current and future trends in topology optimization for additive manufacturing
Liu, J., Gaynor, A. T., Chen, S., Kang, Z., Suresh, K., Takezawa, A., Li, L., Kato, J., Tang, J., Wang, C. C. L., et al. (2018) · Structural and Multidisciplinary Optimization · doi:10.1007/s00158-018-1994-3 · Cited by 870
A review about the engineering design of optimal heat transfer systems using topology optimization
Dbouk, T. (2017) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.10.134 · Cited by 469
State-of-the-art in heat exchanger additive manufacturing
Kaur, I., & Singh, P. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.121600 · Cited by 319
Support structure constrained topology optimization for additive manufacturing
Mirzendehdel, A. M., & Suresh, K. (2016) · Computer-Aided Design · doi:10.1016/j.cad.2016.08.006 · Cited by 318
Metadata
- Authors
- Dede, E. M., Joshi, S. N., & Zhou, F.
- Venue
- Journal of Mechanical Design
- Publisher
- ASME International
- Published
- 2015-10-12
- Volume
- 137
- Issue
- 11
- ISSN
- 0161-8458 (ISSN-L)
- 1050-0472
- 1528-9001
- OpenAlex
- W1863376475
- Cited by
- 312
- References
- 18
- FWCI
- 35.77
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Topology Optimization, Additive Layer Manufacturing, and Experimental Testing of an Air-Cooled Heat Sink. https://app.cochat.ai/papers/10.1115/1.4030989
- The paper
- Dede, E. M., Joshi, S. N., & Zhou, F. (2015). Topology Optimization, Additive Layer Manufacturing, and Experimental Testing of an Air-Cooled Heat Sink. Journal of Mechanical Design. https://doi.org/10.1115/1.4030989
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.