The DOI matches its Crossref record.
Effect of Mechanical Grinding on the Lithium Intercalation Process in Graphites and Soft Carbons
Open accessAbstract
The effects of mechanical grinding on morphology and electrochemical performance of graphite and soft carbon powders with respect to lithium insertion were studied. The morphology of the milled graphitic powders was found to depend strongly upon the nature of the interactions ( e.g. , impact or shear) generated by the two kinds of mixer mills used. For the same milling time, crystallite size was smallest and the density of defects highest for graphitic powders that were ball‐milled using impact interactions. The specific surface area of the milled samples does not increase indefinitely with increased milling time, but there is a critical milling time ( m c ) beyond which the specific surface area goes through a maximum (graphite) or levels off for cokes. By controlling milling conditions, graphite and soft carbon powders with well‐defined morphology, d‐spacings, surface area, and crystallite size can be made. The reversible (reversible amount of inserted Li) vs. irreversible capacity (irreversible lithium loss between the first discharge and charge) was measured for various C/Li cells using various tailor‐made graphite and soft carbon powders. A direct correlation between the irreversible capacity of the milled samples and their specific surface area was observed, consistent with catalytically induced reduction of the electrolyte. For milling times greater than m c , the irreversible capacity remains constant or even decreases while the reversible capacity still increases. With mechanical grinding, both graphite and coke samples having irreversible capacity of 328 mAh/g for a reversible capacity of 708 mAh/g were obtained.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
A review of the electrochemical performance of alloy anodes for lithium-ion batteries
Zhang, W.-J. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2010.07.020 · Cited by 2,140
Hallmarks of mechanochemistry: from nanoparticles to technology
Baláž, P., Achimovičová, M., Baláž, M., Billik, P., Cherkezova-Zheleva, Z., Criado, J. M., Delogu, F., Dutková, E., Gaffet, E., Gotor, F. J., et al. (2013) · Chemical Society Reviews · doi:10.1039/c3cs35468g · Cited by 1,295
Aurbach, D., Markovsky, B., Weissman, I., Levi, E., & Ein-Eli, Y. (1999) · Electrochimica Acta · doi:10.1016/s0013-4686(99)00194-2 · Cited by 969
In search of an optimized electrolyte for Na-ion batteries
Ponrouch, A., Marchante, E., Courty, M., Tarascon, J.-M., & Palacín, M. R. (2012) · Energy & Environmental Science · doi:10.1039/c2ee22258b · Cited by 968
Self-citationCarbon materials for lithium-ion rechargeable batteries
Flandrois, S., & Simon, B. (1999) · Carbon · doi:10.1016/s0008-6223(98)00290-5 · Cited by 742
Metadata
- Authors
- Disma, F., Aymard, L., Dupont, L., & Tarascon, J. ‐.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1996-12-01
- Volume
- 143
- Issue
- 12
- Pages
- 3959-3972
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2038935192
- Cited by
- 176
- References
- 0
- FWCI
- 11.16
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of Mechanical Grinding on the Lithium Intercalation Process in Graphites and Soft Carbons. https://app.cochat.ai/papers/10.1149/1.1837322
- The paper
- Disma, F., Aymard, L., Dupont, L., & Tarascon, J. ‐. (1996). Effect of Mechanical Grinding on the Lithium Intercalation Process in Graphites and Soft Carbons. Journal of The Electrochemical Society. https://doi.org/10.1149/1.1837322
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.