The effect of tool edge preparation on tool life and workpiece surface integrity
The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Abstract
Titanium alloys are classified as ‘hard to machine’ due to their intrinsic properties of low thermal conductivity, low modulus of elasticity, high strength at elevated temperatures and high chemical affinity with all available cutting tool materials. The α-β alloy Ti-6Al-4V is the most common alloy and is used extensively in the aerospace industry for structural components and as compressor blades, discs, casings, etc., in the cooler parts of gas turbine engines. It is critical to industries such as the aerospace industry that the effects of operating parameters on surface integrity are known and understood before new tool geometries and strategies are accepted. There is extensive literature available detailing all aspects of the machinability of titanium alloys, which is briefly reviewed; however, little of this referes specifically to surface integrity. This paper focuses on the effects of cutting tool preparation, cutting speed and feed rate on tool wear/life with special emphasis on workpiece surface integrity.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Evaluation of carbide grades and a new cutting geometry for machining titanium alloys
Komanduri, R., & Reed, W. R. (1983) · Wear · doi:10.1016/0043-1648(83)90011-x · Cited by 86
Cited by
High performance cutting of advanced aerospace alloys and composite materials
M'Saoubi, R., Axinte, D., Soo, S. L., Nobel, C., Attia, H., Kappmeyer, G., Engin, S., & Sim, W.-M. (2015) · CIRP Annals · doi:10.1016/j.cirp.2015.05.002 · Cited by 567
New observations on tool life, cutting forces and chip morphology in cryogenic machining Ti-6Al-4V
Bermingham, M. J., Kirsch, J., Sun, S., Palanisamy, S., & Dargusch, M. S. (2011) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2011.02.009 · Cited by 364
A comprehensive experimental study on surface integrity by end milling Ti–6Al–4V
Sun, J., & Guo, Y. B. (2009) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2008.09.022 · Cited by 317
Wear mechanisms analysis for turning Ti-6Al-4V—towards the development of suitable tool coatings
Jaffery, S. H. I., & Mativenga, P. T. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3427-y · Cited by 111
Sun, D., Lemoine, P., Keys, D., Doyle, P., Malinov, S., Zhao, Q., Qin, X., & Jin, Y. (2018) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-9850-3 · Cited by 80
Metadata
- Authors
- Hughes, J. I., Sharman, A. R. C., & Ridgway, K.
- Venue
- Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Publisher
- SAGE Publications
- Published
- 2004-09-01
- Volume
- 218
- Issue
- 9
- Pages
- 1113-1123
- ISSN
- 0954-4054 (ISSN-L)
- 2041-2975
- OpenAlex
- W2018218290
- Cited by
- 53
- References
- 1
- FWCI
- 0.89
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The effect of tool edge preparation on tool life and workpiece surface integrity. https://app.cochat.ai/papers/10.1243/0954405041897086
- The paper
- Hughes, J. I., Sharman, A. R. C., & Ridgway, K. (2004). The effect of tool edge preparation on tool life and workpiece surface integrity. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. https://doi.org/10.1243/0954405041897086
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.