The Effect of Cutting Tool Material and Edge Geometry on Tool Life and Workpiece Surface Integrity
The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Abstract
Titanium alloys are used extensively in the aerospace industry and are generally classified as ‘hard to machine’. The combination of high strength at elevated temperatures, low thermal conductivity, low modulus of elasticity, and high chemical affinity with all available cutting tool materials means that there are inherent difficulties when machining. The extensive literature detailing all aspects of the machinability of titanium alloys is briefly reviewed; however, little of this refers specifically to surface integrity, which is critical to industries such as aerospace. This paper focuses on the effects that insert geometry had on tool life and workpiece surface integrity when cutting speed, feed rate, and depth of cut were varied. Specifically the effects of edge radius, side cutting edge angle, and edge land are considered. The findings show that whatever combination of tool geometry and operating parameters were used, the surface integrity is remarkably similar, even at relatively high cutting speeds and feed rates.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Evaluation of carbide grades and a new cutting geometry for machining titanium alloys
Komanduri, R., & Reed, W. R. (1983) · Wear · doi:10.1016/0043-1648(83)90011-x · Cited by 86
Cited by
High performance cutting of advanced aerospace alloys and composite materials
M'Saoubi, R., Axinte, D., Soo, S. L., Nobel, C., Attia, H., Kappmeyer, G., Engin, S., & Sim, W.-M. (2015) · CIRP Annals · doi:10.1016/j.cirp.2015.05.002 · Cited by 567
Characteristics of cutting forces and chip formation in machining of titanium alloys
Sun, S., Brandt, M., & Dargusch, M. S. (2009) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2009.02.008 · Cited by 485
Liang, X., Liu, Z., & Wang, B. (2019) · Measurement · doi:10.1016/j.measurement.2018.09.045 · Cited by 280
Influence of Tool Materials on Machinability of Titanium- and Nickel-Based Alloys: A Review
Pervaiz, S., Rashid, A., Deiab, I., & Nicolescu, M. (2014) · Materials and Manufacturing Processes · doi:10.1080/10426914.2014.880460 · Cited by 276
Assessment of the machinability of Ti-6Al-4V alloy using the wear map approach
Jaffery, S. I., & Mativenga, P. T. (2009) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-008-1393-9 · Cited by 119
Metadata
- Authors
- Hughes, J. I., Sharman, A. R. C., & Ridgway, K.
- Venue
- Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Publisher
- SAGE Publications
- Published
- 2006-02-01
- Volume
- 220
- Issue
- 2
- Pages
- 93-107
- ISSN
- 0954-4054 (ISSN-L)
- 2041-2975
- OpenAlex
- W1995233915
- Cited by
- 123
- References
- 1
- FWCI
- 10.34
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The Effect of Cutting Tool Material and Edge Geometry on Tool Life and Workpiece Surface Integrity. https://app.cochat.ai/papers/10.1243/095440506x78192
- The paper
- Hughes, J. I., Sharman, A. R. C., & Ridgway, K. (2006). The Effect of Cutting Tool Material and Edge Geometry on Tool Life and Workpiece Surface Integrity. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. https://doi.org/10.1243/095440506x78192
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.