The DOI matches its Crossref record; 3 of the 3 references it cites were found in a registry or an index.
A parametric study of part distortions in fused deposition modelling using three-dimensional finite element analysis
Abstract
A finite element analysis (FEA) model was previously developed by the current authors to simulate the fused deposition modelling (FDM) process. The model considered coupled thermal and mechanical phenomena and incorporated an element activation function to mimic the additive nature of FDM. Due to repetitive heating and cooling in the FDM process, residual stresses accumulate in a part during deposition. In this study, an FEA model is used to evaluate the distortions of a part. A parametric study, with three factors and three levels, is performed to evaluate the effects of the deposition parameters on residual stresses and part distortions. Prototype models with larger sizes are fabricated, measured, and compared with the simulations. The simulation results are summarized as follows. First, the scan speed is the most significant factor affecting part distortions, followed by the layer thickness. Second, the road width alone is insignificant. However, the interaction between the road width and the layer thickness is significant as well. Third, there are other two-way and three-way interactions that are of secondary significance. In general, residual stresses in FDM parts increase with the layer thickness. Residual stresses also increase with the road width, but to a lesser extent, although largely affected by the layer thickness. The FDM part distortions from the experiment show a similar trend as concluded in the simulations, but without quantitative correlation.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
HAYHURST, A. N. (1997) · Food engineering series · doi:10.1007/978-1-4615-3864-6_3 · Cited by 999
Thermomechanical analysis of the laminated object manufacturing (LOM) process
Sonmez, F. O., & Hahn, H. T. (1998) · Rapid Prototyping Journal · doi:10.1108/13552549810197541 · Cited by 51
Chin, R., Beuth, J., & Amon, C. H. (2000) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.1380200 · Cited by 39
Cited by
Mohamed, O. A., Masood, S. H., & Bhowmik, J. L. (2015) · Advances in Manufacturing · doi:10.1007/s40436-014-0097-7 · Cited by 1,481
Additive manufacturing methods and modelling approaches: a critical review
Bikas, H., Stavropoulos, P., & Chryssolouris, G. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-015-7576-2 · Cited by 1,427
Parametric appraisal of mechanical property of fused deposition modelling processed parts
Sood, A. K., Ohdar, R. K., & Mahapatra, S. S. (2010) · Materials & Design · doi:10.1016/j.matdes.2009.06.016 · Cited by 1,318
Fused filament fabrication of fiber-reinforced polymers: A review
Brenken, B., Barocio, E., Favaloro, A., Kunc, V., & Pipes, R. B. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.01.002 · Cited by 737
A critical review on the fused deposition modeling of thermoplastic polymer composites
Penumakala, P. K., Santo, J., & Thomas, A. (2020) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2020.108336 · Cited by 704
Metadata
- Authors
- Zhang, Y., & Chou, K.
- Venue
- Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Publisher
- SAGE Publications
- Published
- 2008-08-01
- Volume
- 222
- Issue
- 8
- Pages
- 959-968
- ISSN
- 0954-4054 (ISSN-L)
- 2041-2975
- OpenAlex
- W1973464981
- Cited by
- 321
- References
- 3
- FWCI
- 13.14
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: A parametric study of part distortions in fused deposition modelling using three-dimensional finite element analysis. https://app.cochat.ai/papers/10.1243/09544054jem990
- The paper
- Zhang, Y., & Chou, K. (2008). A parametric study of part distortions in fused deposition modelling using three-dimensional finite element analysis. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. https://doi.org/10.1243/09544054jem990
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.