Hydrodynamic force and moment in pure rolling lubricated contacts. Part 2: Point contacts
The DOI matches its Crossref record; 8 of the 8 references it cites were found in a registry or an index.
Abstract
Hydrodynamic rolling force and moments in point contact have been studied in detail using isoviscousrigid (IVR) and elastohydrodynamic (EHL) models. Using fully flooded assumptions, curve-fitted relationships are given for calculating the IVR and EHL hydrodynamic rolling forces. Both are proportional (or almost proportional in the IVR case) to 2 a, the Hertzian contact length being perpendicular to the rolling direction, and are also functions of the dimensionless speed parameter. A single curve-fitted relationship has been derived to cover the full range of operating conditions with a smooth transition from IVR to EHL regime of lubrication. The results obtained are slightly higher than those previously published (the ratio being of the order of 1.5 for usual operating conditions). Point contact and line contact (with a contact length £ being equal to the point contact length 2 a) hydrodynamic rolling forces have also been compared. The point contact forces are about 26 per cent larger than those obtained using line contact relationship (published in part 1) because of a larger domain of integration in the lateral direction. By limiting the width of the integration domain to £ (roller length or ball diameter), the effect of 2 a/£ on the hydrodynamic rolling force has been studied, leading to the derivation of a truncation factor C. As the load increases, 2 a increases and the truncation factor decreases until reaching a limit when ellipse truncation starts because 2 a/£ is equal to or larger than one. Using the truncation factor and limiting the 2 a/£ ratio to one, it was found that point contact and line contact hydrodynamic forces are the same within a few per cent. A single point contact relationship can therefore be suggested, covering the IVR to EHL operating conditions with a smooth transition between these lubrication regimes, and also a smooth transition from point contact to line contact as the load increases and contact ellipse truncation occurs. Finally, calculations of power losses due to the Poiseuille flow in the rolling direction x and in the perpendicular direction z show that the power loss in the z direction is usually very small for wide elliptical contacts and that most of the power is dissipated in the inlet and outlet, with a 26 per cent contribution of the integration domain defined out the range − a < z < a. This result is in line with the truncation factor defined previously.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“According to an order-of-magnitude analysis in [63], the EHL rolling friction can be approximated using the pure-rolling EHL traction, which is due to pressure-induced viscous shear (Poiseuille flow) in the fluid film.”
From Enhancing practical modeling: A neural network approach for locally-resolved prediction of elastohydrodynamic line contacts (2024) · cites this paper as [63]
Citations
Cites
Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part III—Fully Flooded Results
Hamrock, B. J., & Dowson, D. (1977) · Journal of Lubrication Technology · doi:10.1115/1.3453074 · Cited by 1,183
Elasto-hydrodynamic lubrication : the fundamentals of roller and gear lubrication
Dowson, D., & Higginson, G. R. (1966) · Pergamon Press eBooks · Cited by 573
Multilevel Methods in Lubrication
Jacobson, B. (2001) · Tribology International · doi:10.1016/s0301-679x(01)00031-7 · Cited by 201
An Engineering Approach to Hertzian Contact Elasticity—Part I
Houpert, L. (2000) · Journal of Tribology · doi:10.1115/1.1308043 · Cited by 132
Self-citationThe Influence of Fluid Rheology on the Performance of Traction Drives
Tevaarwerk, J. L., & Johnson, K. L. (1979) · Journal of Lubrication Technology · doi:10.1115/1.3453346 · Cited by 104
Simplified Solution for Stresses and Deformations
Hamrock, B. J., & Brewe, D. E. (1983) · Journal of Lubrication Technology · doi:10.1115/1.3254558 · Cited by 84
Houpert, L. (1987) · Journal of Tribology · doi:10.1115/1.3261367 · Cited by 51
Self-citationAnalysis of Starvation Effects on Hydrodynamic Lubrication in Nonconforming Contacts
Brewe, D. E., & Hamrock, B. J. (1982) · Journal of Lubrication Technology · doi:10.1115/1.3253237 · Cited by 31
Research works printed but not linked: 2
- Dalmaz G. Le film mince visqueux dans les contacts hertziens en régimes hydrodynamique et élastohydrodynamique Docteur d'Etat Es Science thesis, no. I-DE-7907, INSA-Lyon, 1979.
- Dowson D., Elastohydrodynamic lubrication, the fundamentals of roller and gear lubrication
Cited by
Numerical investigation of the air–oil two-phase flow inside an oil-jet lubricated ball bearing
Hu, J., Wu, W., Wu, M., & Yuan, S. (2013) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2013.09.013 · Cited by 112
The influence of the lubricant viscosity on the rolling friction torque
Bălan, M. R. D., Stamate, V. C., Houpert, L., & Olaru, D. N. (2013) · Tribology International · doi:10.1016/j.triboint.2013.11.017 · Cited by 59
Self-citationA Dynamic Analysis of Cage Instability in Ball Bearings
Nogi, T., Maniwa, K., & Matsuoka, N. (2017) · Journal of Tribology · doi:10.1115/1.4036451 · Cited by 58
Oh, K.-J., Cao, L., & Chung, S.-C. (2019) · Tribology International · doi:10.1016/j.triboint.2019.105841 · Cited by 52
A simulation analysis for lubricating characteristics of an oil-jet lubricated ball bearing
Liu, J., Ni, H., Xu, Z., & Pan, G. (2021) · Simulation Modelling Practice and Theory · doi:10.1016/j.simpat.2021.102371 · Cited by 50
Cage Friction in High-Speed Spindle Bearings
Brecher, C., Hassis, A., & Rossaint, J. (2013) · Tribology Transactions · doi:10.1080/10402004.2013.843738 · Cited by 47
Friction in starved hydrodynamically lubricated line contacts
Biboulet, N., Colin, F., & Lubrecht, A. A. (2012) · Tribology International · doi:10.1016/j.triboint.2012.09.007 · Cited by 35
Self-citationNogi, T. (2015) · Journal of Tribology · doi:10.1115/1.4030203 · Cited by 29
Olaru, D. N., Bălan, M. R. D., Tufescu, A., Cârlescu, V., & Prisăcaru, G. (2016) · Tribology International · doi:10.1016/j.triboint.2016.11.042 · Cited by 27
Rolling Friction Torque in Ball-Race Contacts Operating in Mixed Lubrication Conditions
Bălan, M., Houpert, L., Tufescu, A., & Olaru, D. N. (2015) · Lubricants · doi:10.3390/lubricants3020222 · Cited by 25
“Miscellaneous relationships for calculating FR have been suggested by Houpert [4] and, recently, by Biboulet and Houpert [5] who suggested relationships corresponding to fully flooded conditions, the meniscus distance xe being located at −d/2 when conducting isoviscous rigid calculations or being a large multiple of b…”
BackgroundMethodResultSelf-citationRolling-Element Bearing Heat Transfer—Part I: Analytic Model
Hannon, W. M. (2015) · Journal of Tribology · doi:10.1115/1.4029732 · Cited by 23
Darul, L., Touret, T., Changenet, C., & Ville, F. (2023) · Tribology Transactions · doi:10.1080/10402004.2023.2235400 · Cited by 21
Starved Elastohydrodynamic Lubrication With Reflow in Elliptical Contacts
Nogi, T., Shiomi, H., & Matsuoka, N. (2017) · Journal of Tribology · doi:10.1115/1.4037135 · Cited by 21
Kelley, J., Schneider, V., Poll, G., & Marian, M. (2024) · Tribology International · doi:10.1016/j.triboint.2024.109988 · Cited by 20
Investigation of the Frictional Behavior in a Roller Linear Motion Guide under Mixed EHL
Cheng, D.-J., Xu, F., Xu, S.-H., & Kim, S.-J. (2020) · Tribology Transactions · doi:10.1080/10402004.2020.1726541 · Cited by 20
Improved friction model for the roller LM guide considering mechanics analysis
Cheng, D.-J., Park, T.-J., & Kim, S.-J. (2018) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-018-0529-6 · Cited by 19
de Veauce, F. D. C., Darul, L., Marchesse, Y., Touret, T., Changenet, C., Ville, F., Amar, L. H. H., & Fossier, C. (2023) · Tribology Transactions · doi:10.1080/10402004.2023.2235395 · Cited by 16
Simulation sudden oil supply in starved high-speed angular contact ball bearing
Tian, J., Zhang, C., Wang, Z., Liang, H., & Guo, D. (2022) · Tribology International · doi:10.1016/j.triboint.2022.107784 · Cited by 15
A general kinematic model for lubricated ball bearings based on the minimum energy hypothesis
Alberdi, P., Arana, A., Oyanguren, A., Larrañaga, J., & Ulacia, I. (2024) · Tribology International · doi:10.1016/j.triboint.2024.109698 · Cited by 15
The Influence of Cage Pocket Lubrication on the Simulation of Deep Groove Ball Bearing Cage Motion
Russell, T. E., Sadeghi, F., Kang, Y. S., & Mazzitelli, I. F. (2023) · Journal of Tribology · doi:10.1115/1.4063624 · Cited by 15
Hydrodynamic Load Calculation in Rolling Element Bearings
Houpert, L. (2016) · Tribology Transactions · doi:10.1080/10402004.2015.1090043 · Cited by 12
“This load generates a tangential hydrodynamic rolling force that has been studied in the IVR and EHD regimes by Biboulet and Houpert (10), leading to a final weighted hydrodynamic rolling force bounded by two assymptotic values (the IVR and EHDones).”
BackgroundSelf-citationForster, N. H., Svendsen, V. R., Givan, G. D., Thompson, K. L., Dao, N.-H., & Nicholson, B. D. (2011) · Tribology Transactions · doi:10.1080/10402004.2010.542276 · Cited by 12
Darul, L., Touret, T., Changenet, C., & Ville, F. (2024) · Lubricants · doi:10.3390/lubricants12010014 · Cited by 11
Lubricated piston ring cylinder liner contact : Influence of the liner microgeometry
Bouassida, H. (2014) · theses.fr (ABES) · doi:10.70675/f6646d5fzd163z432ez9c67z1a13ca439ce6 · Cited by 11
Influence of the Geometry on the Rolling Friction Torque in Lubricated Ball-Race Contacts
Bălan, M. R. D., Stamate, V. C., Houpert, L., Tufescu, A., & Olaru, D. N. (2014) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.658.271 · Cited by 10
“We consider that by decreasing the ball diameter, the oil inlet meniscus distance in the ball-race contacts increases as simulated by Biboulet running very flooded IVR and EHL cases.”
BackgroundResultSelf-citationFriction torque in thrust ball bearings grease lubricated
Ianus, G., Dumitrascu, A., Cârlescu, V., & Olaru, D. N. (2016) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/147/1/012026 · Cited by 9
“The parameter M is included by Biboulet & Houpert to take into consideration the transition from IVR to EHD lubrication regimes and it is calculated with the following equation [4]:”
BackgroundMethodResultInfluentialCai, G., Hou, Y., Wang, X., Sun, S., Zhang, Y., & Wang, N. (2024) · Tribology International · doi:10.1016/j.triboint.2024.110071 · Cited by 8
Analysis of edge rolling based on continuous symmetric parabola curves
Li, X., Wang, H., Liu, Y., Zhang, D., & Zhao, D. (2016) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-016-0587-6 · Cited by 8
Wu, P.-Y., He, C., Chen, G., & Ren, C. (2024) · Measurement · doi:10.1016/j.measurement.2024.116533 · Cited by 6
Lubrication characteristics of ball–cylinder pair in eccentric ball piston pumps
Zhao, H., Wei, C. Y., Jing, C., & Lin, S. (2015) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650115610356 · Cited by 6
Tribological Models for Advanced Ball Bearing Simulation
Houpert, L., Clarke, J., & Penny, C. (2023) · Tribology Transactions · doi:10.1080/10402004.2023.2213470 · Cited by 5
“[21].”
Self-citationPower Losses of Oil-Bath-Lubricated Ball Bearings—A Focus on Churning Losses
de Veauce, F. D. C., Marchesse, Y., Touret, T., Changenet, C., Ville, F., Amar, L., & Fossier, C. (2024) · Lubricants · doi:10.3390/lubricants12110362 · Cited by 5
Influence of lubricant on the friction in an angular contact ball bearing under low load conditions
Popescu, A., & Olaru, D. N. (2020) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/724/1/012040 · Cited by 5
“The transition model for the hydrodynamic rolling force described by Biboulet and Houpert [3] is characterized by the following general equation: FRTrans = FRIVR−FREHL 1+ M”
BackgroundMethodInfluentialModeling of damping in elastohydrodynamic lubricated contacts : Application to gear dynamics
Ankouni, M. (2016) · theses.fr (ABES) · doi:10.70675/f4c9eec2za109z4fafz98fbzb2ad1f5b0c9c · Cited by 4
“Other work studied starved lubrication [29-31], along with friction forces in lubricated contacts [32-33].”
BackgroundFriction Torque in Miniature Ball Bearings
Cojocaru, D., Ianus, G., Cârlescu, V., Chiriac, B., & Olaru, D. N. (2025) · Lubricants · doi:10.3390/lubricants13010012 · Cited by 4
Power loss in grease lubricated ball bearings
Ianus, G., Cojocaru, D., Oprişan, M. C., Paleu, V., & Olaru, D. N. (2020) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/724/1/012009 · Cited by 4
Effects of Carriage Flexibility on Friction Force in Linear Ball Guides
Tong, V.-C., Khim, G., & Hong, S.-W. (2021) · Journal of Tribology · doi:10.1115/1.4052331 · Cited by 4
Combined analytical and empirical modelling of power losses in rolling element bearings
Brossier, P. (2020) · theses.fr (ABES) · doi:10.70675/4b2442e6zf561z4310z9e18zc67c4fd8843f · Cited by 3
Influence of ball bearing contact angle on interface kinematics, load, and sliding power losses
Alberdi, P., Arana, A., Oyanguren, A., Larrañaga, J., & Ulacia, I. (2026) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2026.106396 · Cited by 3
Wu, P., Wang, T., Zhang, C., Gu, L., Li, W., Huang, J., Yue, Z., He, S., & Wang, L. (2026) · Tribology International · doi:10.1016/j.triboint.2026.111826 · Cited by 2
Effects of contact surface shapes on isothermal rolling traction of skewed disks
Ohta, H., Wada, Y., & Takano, Y. (2025) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/13506501251324691 · Cited by 1
“Extensive research has been conducted on rolling traction, and expressions for isothermal rolling traction 2 – 17 have been developed for the lubrication regimes, 18,19 which are used by multiplication with a thermal correction factor 20 – 25 to estimate the actual rolling traction.”
InfluentialÉtude des sources de pertes et des transferts thermiques au sein de paliers à éléments roulants
de Veauce, F. D. C. (2024) · theses.fr (ABES) · doi:10.70675/88dde877ze04dz42dfz9c97ze2276cfab474 · Cited by 1
Etude du comportement thermomécanique des roulements à billes faiblement chargés
Darul, L. (2024) · theses.fr (ABES) · doi:10.70675/113f9f1bz3079z4ed7zb977z43f3698eba7e · Cited by 1
Egawa, K., & Sakaguchi, T. (2026) · Journal of Tribology · doi:10.1115/1.4072104 · Cited by 1
Friction Torque in Low Loaded Thrust Ball Bearings
Bălan, M. R. D., Tufescu, A., Benchea, M. I., & Olaru, D. N. (2015) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.809-810.676 · Cited by 1
“The experimental results obtained evidenced a good correlation with the theoretical models for rolling friction resistance in lubricated ball–race contacts developed in [5].”
ResultEgawa, K., & Sakaguchi, T. (2026) · Journal of Tribology · doi:10.1115/1.4072105 · Cited by 1
Film thickness in miniature ball bearing grease lubricated
Cojocaru, D., Ianus, G., & Cârlescu, V. (2022) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/1262/1/012005 · Cited by 1
Influence of the Cage on the Friction Torque in Miniature Angular Contact Ball Bearings
Dumitrascu, A., Cojocaru, D., Cârlescu, V., Zaharia, A., & Olaru, D. N. (2026) · Lubricants · doi:10.3390/lubricants14040145 · Cited by 1
“…resistance developed in the outer and inner races of the ball, FR o and FR i , respectively, is determined by Biboulet and Houpert’s equations [18]: where E* is the reduced Young modulus of the ball and races, U o , i and W o , i are the classical dimensionless speed and load parameters,…”
Ohta, H., & Takano, Y. (2026) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/13506501251411002
“Additionally, isothermal rolling traction expressions for multiple lubrication regimes in oil lubrication have been proposed by Biboulet and Houpert 12,13 for the IVR and EHL regimes, and by Ohta et al. 14,15 for the IVR, PVR, and EHL regimes.”
Friction models for grease lubricated ball-race contacts
Ianus, G., Cojocaru, D., Oprişan, M. C., Cârlescu, V., & Olaru, D. N. (2020) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/997/1/012012
“(26) where M is Biboulet and Houpert parameter given by equation (10).”
BackgroundMethodInfluentialZhou, R., Yang, D., Li, X., & Li, S. (2026) · Mechanisms and machine science · doi:10.1007/978-3-032-01363-7_45
Experimental Friction Torque in Miniature Ball Bearings Grease Lubricated
Cojocaru, D., Chiriac, B., Cârlescu, V., & Zaharia, A. (2026) · Buletinul Institutului Politehnic din Iaşi. Secţia Construcţii de maşini/Buletinul Institutului Politehnic din Iaşi, Secţia Construcţii de maşini · doi:10.2478/bipcm-2026-0001
“At the same time, the presence of the oil in the balls-race contacts leads to the development of important hydrodynamic resistance forces (Houpert, 1999, 2002; Biboulet and Houpert, 2010).”
Metadata
- Authors
- Biboulet, N., & Houpert, L.
- Affiliations
- TIMKEN Europe, Colmar, France
- Venue
- Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology
- Publisher
- SAGE Publications
- Published
- 2010-05-14
- Volume
- 224
- Issue
- 8
- Pages
- 777-787
- ISSN
- 1350-6501 (ISSN-L)
- 2041-305X
- OpenAlex
- W4247538131
- Cited by
- 51
- References
- 8
- Citations by year
- 2026: 6 · 2025: 2 · 2024: 8 · 2023: 4 · 2022: 2 · 2021: 2 · 2020: 5 · 2019: 2 · 2018: 1 · 2017: 2 · 2016: 4 · 2015: 6 · 2014: 2 · 2013: 3 · 2012: 1
- FWCI
- 3.04
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- journals.sagepub.com/page/policies/text-and-data-mining-license (tdm)
- Locations
- Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology (publishedVersion)
- HAL (submittedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Physical Sciences › Engineering › Mechanical Engineering › Gear and Bearing Dynamics Analysis
- Physical Sciences › Engineering › Mechanics of Materials › Adhesion, Friction, and Surface Interactions
- Keywords
- hydrodynamic moments, point contacts, line contact, elastohydrodynamic lubrication
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.