Student or educator? Sign up with your school email and get 6 months of Pro free.
Cited by 339

The DOI matches its Crossref record; 7 of the 7 references it cites were found in a registry or an index.

Modeling and Measuring the Effect of Refraction on the Depth Resolution of Confocal Raman Microscopy

Everall, Neil J.·2000·Applied Spectroscopy

Abstract

A simple ray-tracing analysis has been used to predict the effect of refraction at the sample/air interface, on the depth resolution of confocal Raman microscopy. This analysis applies to the “z-scanning”, or “optical sectioning”, approach to obtaining depth profiles, where the laser beam is incident normal to the sample surface, and spectra are recorded sequentially as the focus is moved deeper into the material. It is shown that when a “dry” metallurgical objective (the most common configuration for commercial Raman microscopes) is used, both the position and the depth of focus increase dramatically as the beam is focused deeper into the sample. It quickly becomes impossible to obtain “pure” spectra of thin layers that are buried more than a few micrometers below the air interface. Equations are presented which model the intensity response expected when focusing through a coating into a substrate. The model requires knowledge of the sample refractive index, the numerical aperture, and the laser beam intensity distribution at the limiting aperture, of the objective. Given these values, one can predict the substrate Raman intensity as a function of the nominal focal point within the sample. For a 36 μm coating on a thick substrate, we predict that even for a perfectly sharp interface (<<1 μm), substrate bands rise slowly (over an apparent distance of 10 μm or more), and are strong when the focus is apparently only ∼ 18 μm below the air/coating interface. This prediction was confirmed through experimental observation. The model was also used to analyze literature data that had been interpreted previously as showing interfacial diffusion in polymer laminates. The model correctly reproduced the main features of the observed data without invoking interfacial penetration—the optical aberrations alone accounted for almost all the observed broadening and the fact that the apparent thickness of the buried layer is also distorted. It was concluded that, with the use of this illumination geometry, it is very difficult to detect or quantify interfacial broadening unless it occurs on a very large scale indeed (tens of micrometers). It is concluded that ‘optical sectioning’ cannot be recommended for quantitative depth profiling at significant depths using metallurgical objectives. The optimum practical solution is to cut a cross section and map laterally across the sample, thereby utilizing and maintaining the excellent (lateral) resolution of the Raman microprobe. An alternative solution is to use an immersion objective to minimize refraction at the sample surface.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1366/0003702001950382

Cites

7 of 7 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 7 references

Cited by

See all 339

Metadata

Authors
Everall, N. J.
Venue
Applied Spectroscopy
Published
2000-06
Volume
54
Issue
6
Pages
773-782
ISSN
  • 0003-7028 (ISSN-L)
  • 1943-3530
OpenAlex
W2064362324
Cited by
339
References
7
FWCI
12.42
Type
journal article
Language
en
Open access
closed

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Modeling and Measuring the Effect of Refraction on the Depth Resolution of Confocal Raman Microscopy. https://app.cochat.ai/papers/10.1366/0003702001950382
The paper
Everall, N. J. (2000). Modeling and Measuring the Effect of Refraction on the Depth Resolution of Confocal Raman Microscopy. Applied Spectroscopy. https://doi.org/10.1366/0003702001950382

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.