The DOI matches its Crossref record; the references it cites are not checked yet.
Boyunduruksuz ve Segmentli Armatür tipi Eksenel Akılı Asenkron Motorun, Rotor Bar Sayısı, Malzemesi ve Çalışma Hızı Kapsamında Performans Karşılaştırması
Abstract
Bu çalışma literatürde oldukça sınırlı sayıda yer bulan Boyunduruksuz ve Segmentli Armatür tipi (YASA) Eksenel Akılı Asenkron Motor (EAASM) yapısını detaylıca ele almaktadır. Çalışmada, YASA tipi çift rotor mimarisine sahip EAASM, stator yapısı sabit tutularak; alüminyum ve bakır rotor bar malzemesi kullanılarak 5 farklı rotor bar sayısı için 3 farklı çalışma hızında Sonlu Eleman Yöntemleri (SEY) ile analiz edilmiştir. Çalışmanın temel amacı; rotor bar sayısı, rotor bar malzemesi ve çalışma hızı parametrelerinin motor performansı üzerindeki etkilerini sistematik olarak kıyaslamak ve bundan sonra yapılacak çalışmalara da kolaylık sağlamaktır. 6 kutup, 9 stator oluğuna sahip motor 29,31,35,37 ve 41 rotor bar sayısı için hem alüminyum hem de bakır rotor bar malzemesi kullanılarak sınanmıştır. 1000,2000 ve 3000 rpm çalışma hızlarının ele alındığı analizlerde tork, tork dalgalanması, verimlilik ve kayıplar kıyaslanmış olup çok kriterli optimizasyonun yorumlanabilmesi adına Normalize Performans İndeksi ile söz konusu çalışma için optimal motor yapısı belirlenmiştir. Analiz sonuçları rotor bar malzemesi olarak bakır kullanılması durumunda 41 bar yapısının 3 farklı çalışma hızında da en uygun seçim olduğunu, alüminyum kullanılması durumunda ise 1000 rpm için 29 bar yapısının, 2000 ve 3000 rpm hızlarında ise 41 bar konfigürasyonunun optimum rotor oluk sayısı olduğunu göstermektedir. Elde edilen veriler, YASA tipi EAASM tasarımı için yapılacak olan ileriki çalışmalar adına ihtiyaç odaklı parametre optimizasyonuna olanak sağlarken, bu kapsamda araştırmacılara kolaylık sağlayacağı öngörülmektedir.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
The citation lists haven’t been fetched yet
Research works printed but not linked: 48
- [1] De Almeida, A. T., Ferreira, F. J., & Baoming, G. (2013, April). Beyond induction motors—Technology trends to move up efficiency. In 49th IEEE/IAS Industrial & Commercial Power Systems Technical Conference (pp. 1-13). IEEE. · doi:10.1109/icps.2013.6547330
- [2] Kahourzade, S., Mahmoudi, A., Ravji, R., & Soong, W. L. (2019, September). Line-Start axial-flux PM motors: Introduction of a new machine topology. In 2019 IEEE energy conversion congress and exposition (ECCE) (pp. 7027-7034). IEEE. · doi:10.1109/ecce.2019.8912992
- [3] Amin, S., Khan, S., & Bukhari, S. S. H. (2019, January). A comprehensive review on axial flux machines and its applications. In 2019 2nd International Conference on Computing, Mathematics and Engineering Technologies (iCoMET) (pp. 1-7). IEEE. · doi:10.1109/icomet.2019.8673422
- [4] Mushid, F. C., & Dorrell, D. G. (2017, April). Review of axial flux induction motor for automotive applications. In 2017 IEEE Workshop on Electrical Machines Design, Control and Diagnosis (WEMDCD) (pp. 146-151). IEEE. · doi:10.1109/wemdcd.2017.7947738
- [5] Spooner, E., & Chalmers, B. J. (1988, September). Toroidally-wound, slotless, axial-flux, permanent-magnet, brushless-DC motors. In Proc. International Conference on Electrical Machines (Vol. 3, pp. 81-86).
- [6] Al-Badi, A., Gastli, A., Bourdoucen, H., & Jervase, J. (2000). Evolution of axial-field electrical machines. Sultan Qaboos University Journal for Science, 5(2), 227-245. · doi:10.24200/squjs.vol5iss0pp227-245
- [7] Cao, Z., Mahmoudi, A., Kahourzade, S., Soong, W. L., & Summers, J. R. (2020, December). A comparative study of axial-flux versus radial-flux induction machines. In 2020 IEEE International Conference on Power Electronics, Drives and Energy Systems (PEDES) (pp. 1-6). IEEE. · doi:10.1109/pedes49360.2020.9379868
- [8] Özsoy, M., Kaplan, O., & Akar, M. (2024). FEM-based analysis of rotor cage material and slot geometry on double air gap axial flux induction motors. Ain Shams Engineering Journal, 15(2), 102393. · doi:10.1016/j.asej.2023.102393
- [9] Dianati, B., Kahourzade, S., & Mahmoudi, A. (2020). Optimization of axial-flux induction motors for the application of electric vehicles considering driving cycles. IEEE Transactions on Energy Conversion, 35(3), 1522-1533. · doi:10.1109/tec.2020.2976625
- [10] Nobahari, A., Darabi, A., & Hassannia, A. (2017, February). Axial flux induction motor, design and evaluation of steady state modelling using equivalent circuit. In 2017 8th Power Electronics, Drive Systems & Technologies Conference (PEDSTC) (pp. 353-358). IEEE. · doi:10.1109/pedstc.2017.7910351
- [11] Cao, Z., Mahmoudi, A., Kahourzade, S., & Soong, W. L. (2021, September). An overview of axial-flux induction machine. In 2021 31st Australasian Universities Power Engineering Conference (AUPEC) (pp. 1-6). IEEE. · doi:10.1109/aupec52110.2021.9597784
- [13] Mirzaei, M., Mirsalim, M., & Abdollahi, S. E. (2007). Analytical modelling of axial air gap solid rotor induction machines using a quasi-three-dimensional method. IEEE Transactions on Magnetics, 43(7), 3237-3242. · doi:10.1109/tmag.2007.894215
- [14] Gieras, J. F., Wang, R. J., & Kamper, M. J. (2008). Axial flux permanent magnet brushless machines. Dordrecht: Springer Netherlands. · doi:10.1007/978-1-4020-8227-6
- [16] Woolmer, T. J., & McCulloch, M. D. (2007, May). Analysis of the Yokeless and segmented armature machine. In 2007 IEEE International Electric Machines & Drives Conference (Vol. 1, pp. 704-708). IEEE. · doi:10.1109/iemdc.2007.382753
- [17] Chang, J., Fan, Y., Zhu, B., Luo, L., Wu, J., Pan, Y., & Kang, P. (2020). Design of a new type Yokeless and segmented armature axial flux machine. International Journal of Applied Electromagnetics and Mechanics, 62(4), 823-834. · doi:10.3233/jae-190085
- [18] Taran, N., Klink, D., Heins, G., Rallabandi, V., Patterson, D., & Ionel, D. M. (2021). A comparative study of Yokeless and segmented armature versus single sided axial flux PM machine topologies for electric traction. IEEE Transactions on Industry Applications, 58(1), 325-335. · doi:10.1109/tia.2021.3131427
- [19] Daut, I., Anayet, K., Gomesh, N., Asri, M., & Irwan, Y. M. (2009, December). Comparison of Copper Rotor Bars with Aluminium Rotor Bars Using FEM Software--A Performance Evaluation. In 2009 Second International Conference on Computer and Electrical Engineering (Vol. 1, pp. 456-459). IEEE. · doi:10.1109/iccee.2009.261
- [20] Babypriya, B., & Gomathi, S. (2021). Numerical analysis on impact of choice of number of rotor slots on performance of three phase induction motor. Materials Today: Proceedings, 45, 2364-2370. · doi:10.1016/j.matpr.2020.10.706
- [21] Gyftakis, K. N., & Kappatou, J. (2013). The impact of the rotor slot number on the behaviour of the induction motor. Advances in Power Electronics, 2013(1), 837010. · doi:10.1155/2013/837010
- [22] Lordoglu, A., Gulbahce, M. O., & Kocabas, D. A. (2021). A comprehensive disturbing effect analysis of multi-sectional rotor slot geometry for induction machines in electrical vehicles. IEEE Access, 9, 49590-49600. · doi:10.1109/access.2021.3068821
- [23] Mushid, F. C., & Dorrell, D. G. (2017, April). Review of axial flux induction motor for automotive applications. In 2017 IEEE Workshop on Electrical Machines Design, Control and Diagnosis (WEMDCD) (pp. 146-151). IEEE · doi:10.1109/wemdcd.2017.7947738
- [24] Evans, P. D., Brown, D., & Eastham, J. F. (1987, August). A study of permanent magnet disc motor design. In BICEM Proceedings (pp. 729-732).
- [25] Spooner, E., & Chalmers, B. J. (1992, November). ‘TORUS’: A slotless, toroidal-stator, permanent-magnet generator. In IEE Proceedings B (Electric Power Applications) (Vol. 139, No. 6, pp. 497-506). IEE · doi:10.1049/ip-b.1992.0061
- [26] Finley, W. R., & Hodowanec, M. M. (2002). Selection of copper versus aluminium rotors for induction motors. IEEE Transactions on Industry Applications, 37(6), 1563-1573. · doi:10.1109/28.968162
- [27] Akçomak, M., & Partal, S. Z. Çift Kafesli Rotorda Alüminyum ve Bakırın Birlikte Kullanımının Asenkron Motor Verimine Etkisinin İncelenmesi. EMO Bilimsel Dergi, 12(2), 15-25.
- [28] Momin, A. (2024). Review of Electrical Steels with their Properties and Recent Trends for Improvement. Technology, 17(41), 4270-4286. · doi:10.17485/ijst/v17i41.1502
- [29] Gundogdu, T., Komurgoz, G., & Mantar, B. (2014, April). Implementation of fractional slot concentrated windings to induction machines. In 7th IET International Conference on Power Electronics, Machines and Drives (PEMD 2014) (pp. 1-6). IET. · doi:10.1049/cp.2014.0258
- [30] Cros, J., & Viarouge, P. (2002). Synthesis of high performance PM motors with concentrated windings. IEEE transactions on energy conversion, 17(2), 248-253. · DOI · Paper page
- [31] El-Refaie, A. M., & Jahns, T. M. (2004, October). Optimal flux weakening in surface PM machines using concentrated windings. In Conference Record of the 2004 IEEE Industry Applications Conference, 2004. 39th IAS Annual Meeting. (Vol. 2, pp. 1038-1047). IEEE. · doi:10.1109/ias.2004.1348541
- [32] Zhu, Z. Q., & Howe, D. (1997, May). Winding inductances of brushless machines with surface-mounted magnets. In 1997 IEEE International electric machines and drives conference record (pp. WB2-2). IEEE. · doi:10.1109/iemdc.1997.604305
- [33] Reddy, P. B., Jahns, T. M., & El-Refaie, A. M. (2008, October). Impact of winding layer number and slot/pole combination on AC armature losses of synchronous surface PM machines designed for wide constant-power speed range operation. In 2008 IEEE Industry Applications Society Annual Meeting (pp. 1-8). IEEE. · doi:10.1109/08ias.2008.57
- [34] Bitsi, K., Beniakar, M. E., Wallmark, O., & Bosga, S. G. (2020, August). Preliminary electromagnetic sizing of axial-flux induction machines. In 2020 International Conference on Electrical Machines (ICEM) (Vol. 1, pp. 284-290). IEEE. · doi:10.1109/icem49940.2020.9270719
- [35] Keskin Arabul, F., Senol, I., & Oner, Y. (2020). Performance analysis of axial-flux induction motor with skewed rotor. Energies, 13(19), 4991. · doi:10.3390/en13194991
- [36] Woolmer, T. J. T. (2009). The Yokeless and segmented armature machine developed for the LIFECar (Doctoral dissertation, University of Oxford).
- [37] Aslaner, H., & Akar, M. “Boyunduruksuz ve Segmentli Armatür tipi Eksenel Akılı Asenkron Motorun 2 Boyutlu ve 3 Boyutlu Sonlu Eleman Modelleme Sonuçlarının Karşılaştırılması,” in Proc. 6th International Conference on Recent Academic Studies (ICRAS), pp. 5–18, 2026.
- [39] Yan, B., Li, X., Sun, Y., & Tan, Y. (2023). End Effect Equivalence in the 2-D Finite Element Analysis of a Line-Start Permanent Magnet Synchronous Motor with Hybrid Solid Rotor. Energies, 16(19), 6766 · doi:10.3390/en16196766
- [40] Lipo, T. A. (1988). Recent progress in the development in solid-state AC motor drives. IEEE Transactions on Power Electronics, 3(2), 105-117. · doi:10.1109/63.4340
- [41] Bose, B. K. (2005). Adjustable speed ac drives—A technology status review. Proceedings of the IEEE, 70(2), 116-135. · doi:10.1109/proc.1982.12259
- [43] Kirtley, J. L., Cowie, J. G., Brush, E. F., Peters, D. T., & Kimmich, R. (2007, June). Improving induction motor efficiency with die-cast copper rotor cages. In 2007 IEEE Power Engineering Society General Meeting (pp. 1-6). IEEE. · doi:10.1109/pes.2007.385767
- [44] Zhao, A., Chen, H., Boßer, C., & Leksell, M. (2024). FEM and CFD thermal modelling of an axial-flux induction machine with experimental validation. Case Studies in Thermal Engineering, 53, 103879. · doi:10.1016/j.csite.2023.103879
- [46] Bertotti, G. (1988). General properties of power losses in soft ferromagnetic materials. IEEE Transactions on magnetics, 24(1), 621-630. · DOI · Paper page
- [47] Duan, Y., Zhao, J., Xiong, Y., Wang, H., & Tian, J. (2025). Study on Eddy Current Loss Characteristics and Multi-Objective Optimization of High-Speed Solid Rotor Induction Motors. Electronics, 14(20), 4085. · doi:10.3390/electronics14204085
- [48] Özsoy, M., Kaplan, O., & Akar, M. (2023). Implementation of Different 2D Finite Element Modelling Approaches in Axial Flux Induction Motors. Electric Power Components and Systems, 51(19), 2385-2396. · doi:10.1080/15325008.2023.2240806
- [49] Wang, Q., Wang, J., & Geng, W. (2024, November). Equivalent two-dimensional finite element analysis of axial flux induction motor with double stator and single rotor. In 2024 27th International Conference on Electrical Machines and Systems (ICEMS) (pp. 2556-2562). IEEE. · doi:10.23919/icems60997.2024.10921195
- [50] Gerçekcioğlu, H. S., & Akar, M. (2021). Efficiency and performance comparison between synchronous reluctance and induction motor in axial flux concept. Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji, 9(2), 297-316. · doi:10.29109/gujsc.910521
- [51] Montero, M. A. T., Garces, A. E. H., Ladino, J. A. T., & Collao, R. R. W. (2017). Simulation and analysis of an axial flux induction machine. IEEE Latin America Transactions, 15(7), 1263-1269. · doi:10.1109/tla.2017.7959345
- [52] Gundogdu, T. (2018). Advanced non-overlapping winding induction machines for electrical vehicle applications (Doctoral dissertation, University of Sheffield).
- [53] Huang, P., Li, H., & Yang, C. (2021, February). A Yokeless axial flux induction motor for electric vehicles based on grain-oriented silicon steel. In Journal of Physics: Conference Series (Vol. 1815, No. 1, p. 012042). IOP Publishing. · doi:10.1088/1742-6596/1815/1/012042
Metadata
- Authors
- Aslaner, H., & Akar, M.
- Venue
- Erzincan Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Published
- 2026-08-31
- Volume
- 19
- Issue
- 2
- Pages
- 158-181
- ISSN
- 1307-9085
- Cited by
- 0
- Language
- en
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Boyunduruksuz ve Segmentli Armatür tipi Eksenel Akılı Asenkron Motorun, Rotor Bar Sayısı, Malzemesi ve Çalışma Hızı Kapsamında Performans Karşılaştırması. https://app.cochat.ai/papers/10.18185/erzifbed.1914062
- The paper
- Aslaner, H., & Akar, M. (2026). Boyunduruksuz ve Segmentli Armatür tipi Eksenel Akılı Asenkron Motorun, Rotor Bar Sayısı, Malzemesi ve Çalışma Hızı Kapsamında Performans Karşılaştırması. Erzincan Üniversitesi Fen Bilimleri Enstitüsü Dergisi. https://doi.org/10.18185/erzifbed.1914062
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.