The DOI matches its Crossref record; 23 of the 23 references it cites were found in a registry or an index; 1 of the 5 sources its claims cite were checked for support.
Implementation of a 6U CubeSat Electrical Power System Digital Twin
Open accessAbstract
This paper presents the design of a digital twin for a 6U CubeSat electrical power system, including the solar arrays, solar array regulators, battery, power distribution unit, and load subsystems.
Overview
CoChat Summary
TL;DR
This paper develops and experimentally validates a real-time digital twin for a 6U CubeSat electrical power system, including solar arrays, solar array regulators, battery, power distribution unit, and loads. The digital twin closely matches the physical system in validation tests and is used for CHIL/PHIL testing and a full low Earth orbit orbital-cycle simulation.
Key findings
- The digital twin’s real-time outputs closely matched the physical EPS in validation tests; during an 18 W step load applied for 6 s, the SAR transitioned between MPPT and VEOC modes and experimental and DT waveforms were “almost identical.”
- The DT was implemented on a Typhoon HIL404 real-time simulator with a simulation step as low as 500 ns; the reported loop-back latency was 1650 ns, comprising 500 ns sampling delay, 500 ns state calculation, 500 ns output calculation, and 150 ns analog output latency.
- CHIL tests evaluated the control circuit across a solar-cell temperature range of −50 °C to +100 °C, and PHIL tests with a digital perturb-and-observe MPPT showed the SAS operating point oscillating around the MPP at approximately 15 V.
- A complete EPS DT simulated a full orbital cycle in LEO at 793 km altitude with nadir pointing, capturing MPPT mode, VEOC mode, battery charging/discharging, and eclipse behavior.
Methods
- The DT models four solar array sections, each an 8S1P string of CESI CTJ30 triple-junction cells characterized at AM0 1366.1 W/m² and 85 °C; the SAS uses a single-diode model with parameters extracted by the two-step linear least-squares method.
- The SAR is modeled as a synchronous buck DC/DC converter with peak-current inner control and outer voltage loops; the battery is a 2S2P pack of four 2600 mAh Samsung Li-Ion 18650 cells, modeled with parameters fitted from a discharge curve measured at 25 °C and 520 mA (0.1 C).
- Validation compared real-time DT outputs with experimental waveforms from the physical EPS; CHIL and PHIL tests integrated real hardware with simulated subsystems, and the complete DT used irradiance and temperature profiles computed with Radian System Software 2024 for a LEO orbital cycle.
Limitations
- The paper states that solar-cell degradation from space radiation and thermal cycling was not considered, and that battery temperature and state of health were assumed constant over the mission.
- The paper states that implementing the EPS CubeSat DT requires high computational power equipment and recommends averaged models for switching converters at present.
- Evident from the text: the buck converter model assumes no conduction or switching losses and no AC switching ripple, and the PDU lines are simplified as constant power loads with fixed efficiencies (99% unregulated, 95% for 5 V, 93% for 3.3 V); no quantitative error metrics for the DT-versus-physical comparison are reported.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
1 Valid · 2 Not valid · 4 Not checked · 31 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“A notable feature of this battery model is that its parameters can be easily deduced from experimental discharge curves.”
§ Implementation of a 6U CubeSat Electrical Power System Digital Twin > 2.3. Battery (BAT)
What the sources say
- Supportedcites [18] Tremblay, 2009, Experimental Validation of a Battery Dynamic Model for EV Applications, World Electr. Veh. J. source
Section 3, “Extracting the parameters,” explicitly describes parameter extraction as simple and says that three points on a steady-state discharge curve are sufficient to obtain the model parameters. The claim is a fair paraphrase of that feature. (LLM, conf=0.91)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The first graph (top) illustrates how the control circuit sets the SAS MPP voltage, which decreases as the temperature rises.”
§ Implementation of a 6U CubeSat Electrical Power System Digital Twin > 5. Conclusions
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Additionally, to demonstrate the advanced capabilities of this model, the digital twin is used to simulate the CubeSat electrical power system behavior in real time throughout a complete orbital cycle in low Earth orbit conditions.”
§ Implementation of a 6U CubeSat Electrical Power System Digital Twin > Abstract
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Experimental tests confirm its feasibility, showing that the digital twin's real-time outputs closely match those of the physical system.”
§ Implementation of a 6U CubeSat Electrical Power System Digital Twin > Abstract
boostedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“It can be observed how the operating point adapts as the MPP point changes.”
§ Implementation of a 6U CubeSat Electrical Power System Digital Twin > 5. Conclusions
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
11 more claims
Create a free account to see all 38 claims and every source verdict.
- Probably not a substantial claim. 12
- It may state two separate claims as one. 15
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Implementation of a 6U CubeSat Electrical Power System Digital Twin > 2.2. Solar Array Regulators (SARs)
“Linear Technology LT3845 serves as the controller for each converter.”
§ Implementation of a 6U CubeSat Electrical Power System Digital Twin > 2.2. Solar Array Regulators (SARs)
“LT3485 performs peak-current control internally and integrates an anti-slope compensation circuit to mitigate current limit reduction associated with slope compensation at high duty cycles.”
Citations
Cites
Optimization of Perturb and Observe Maximum Power Point Tracking Method
Femia, N., Petrone, G., Spagnuolo, G., & Vitelli, M. (2005) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2005.850975 · Cited by 3,002 · cited 2×
“Speci fi cally, the digital perturb and observe (P&O) method [21], known for its cost-e ff ective implementation, was used in this test. a temperature variation using a CHIL simulation.”
MethodExperimental Validation of a Battery Dynamic Model for EV Applications
Tremblay, O., & Dessaint, L.-A. (2009) · World Electric Vehicle Journal · doi:10.3390/wevj3020289 · Cited by 1,223 · cited 1×
“A notable feature of this The steady-state general battery model described in [18] was utilized; this model comprises a nonlinear voltage source (E) with a series resistance (Rbat). ba tt ery model is that its parameters can be easily deduced from experimental discharge curves.”
MethodDigital Twins: A Survey on Enabling Technologies, Challenges, Trends and Future Prospects
Mihai, S., Yaqoob, M., Hung, D. V., Davis, W., Towakel, P., Raza, M., Karamanoglu, M., Barn, B., Shetve, D., Prasad, R. V., et al. (2022) · IEEE Communications Surveys & Tutorials · doi:10.1109/comst.2022.3208773 · Cited by 1,049
Two-Step Linear Least-Squares Method for Photovoltaic Single-Diode Model Parameters Extraction
Toledo, F. J., Blanes, J. M., & Galiano, V. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2793216 · Cited by 175 · cited 2×
“Figure 2 illustrates curves using the two-step linear least-squares (TSLLS) method, as presented 15].”
MethodSelf-citationEdrington, C. S., Steurer, M. M., Langston, J., et al. (2015) · Proceedings of the IEEE · doi:10.1109/jproc.2015.2460676 · Cited by 156 · cited 1×
“On the other hand, PHIL tests only use the DT to simulate the control subsystem of the SAR (MPPT and outer voltage loops) in real time and interact with the rest of the hardware [20].”
MethodAdvanced CubeSat Antennas for Deep Space and Earth Science Missions: A review
Chahat, N., Decrossas, E., Gonzalez-Ovejero, D., Yurduseven, O., Radway, M. J., Hodges, R. E., Estabrook, P., Baker, J. D., Bell, D. J., Cwik, T. A., et al. (2019) · IEEE Antennas and Propagation Magazine · doi:10.1109/map.2019.2932608 · Cited by 113
Chen, Z., Liang, D., Jia, S., Yang, L., & Yang, S. (2023) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2023.3255249 · Cited by 72 · cited 1×
“A DT is a virtual representation of a physical system, enabling engineers to simulate different scenarios in real time, monitor its performance, and optimize its operation throughout its lifecycle [7,8].”
BackgroundDigital Twin Models: Functions, Challenges, and Industry Applications
Rayhana, R., Bai, L., Xiao, G. G., Liao, M., & Liu, Z. (2024) · IEEE Journal of Radio Frequency Identification · doi:10.1109/jrfid.2024.3387996 · Cited by 72
Application Status and Prospect of Digital Twin for On-Orbit Spacecraft
Yang, W., Zheng, Y., & Li, S. (2021) · IEEE Access · doi:10.1109/access.2021.3100683 · Cited by 58 · cited 2×
“However, until recently, DTs were virtually nonexistent in the microsatellite industry, but it has started to attract interest in recent years [10–13].”
BackgroundMethodDesign and Control for High-Reliability Power Electronics: State-of-the-Art and Future Trends
Marquez, A., Buticchi, G., Chub, A., & Dalessandro, L. (2023) · IEEE Journal of Emerging and Selected Topics in Industrial Electronics · doi:10.1109/jestie.2023.3287513 · Cited by 52 · cited 1×
“On the other hand, the concept of digital twin (DT) has gained traction in various industries, including aerospace, as a means of bridging the gap between physical systems and digital simulations [4–6].”
Background
Cited by
State-of-the-Art DC-DC Converters for Satellite Applications: A Comprehensive Review
Ravindran, R., & Massoud, A. M. (2025) · Aerospace · doi:10.3390/aerospace12020097 · Cited by 34
Elnosh, A., Calais, M., & Parlevliet, D. A. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.116326 · Cited by 28
Sbarra, R. G., Pasquali, M., Coppotelli, G., Gaudenzi, P., di Ienno, D., Ciancarelli, C., & Picci, N. (2025) · Energies · doi:10.3390/en18215858 · Cited by 13
“Digital Twins have also been designed for the CubeSats electrical power system [10].”
Geng, W., Yu, F., Jiao, Y. Q., et al. (2025) · IEEE Sensors Journal · doi:10.1109/jsen.2025.3577330 · Cited by 4
“The current research mainly focuses on obtaining the maximum energy input for surface-mounted solar cells without using solar sensors, including how to adjust the attitude and determine the most suitable installation position [17], [18], [19], [20], [21], [22].”
Elmayah, A., Ibrahim, M., Sarhan, A. A., et al. (2025) · doi:10.1109/iceeng64546.2025.11031290 · Cited by 1
“A recent research [7] focuses on the CubeSat EPS and its modelling, including the power distribution unit and electrical loads.”
Metadata
- Authors
- Casado, P., Torres, C., Blanes, J. M., Garrigós, A., & Marroquí, D.
- Affiliations
- Universitat de Miguel Hernández d'Elx (ES)
- Space Power & Electronic System Research Group, University Miguel Hernández of Elche, 03202 Elche, Spain
- Corresponding author
- Casado, Pablo
- Venue
- Aerospace
- Publisher
- MDPI AG
- Published
- 2024-08-21
- Volume
- 11
- Issue
- 8
- Pages
- 688
- ISSN
- 2226-4310 (ISSN-L)
- OpenAlex
- W4401890061
- Cited by
- 13
- References
- 23
- Citations by year
- 2026: 5 · 2025: 8
- FWCI
- 2.25
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Aerospace (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Funders
- European Union NextGenerationEU (ASFAE/2022/21)
- Topics
- Physical Sciences › Engineering › Aerospace Engineering › Spacecraft Design and Technology
- Physical Sciences › Engineering › Control and Systems Engineering › Real-time simulation and control systems
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Space Technology and Applications
- Keywords
- digital twin, CubeSat, power systems, solar arrays, batteries, power distribution unit, hardware-in-the-loop testing, real-time simulation, telemetry data, fault diagnosis
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Implementation of a 6U CubeSat Electrical Power System Digital Twin. https://app.cochat.ai/papers/10.3390/aerospace11080688
- The paper
- Casado, P., Torres, C., Blanes, J. M., Garrigós, A., & Marroquí, D. (2024). Implementation of a 6U CubeSat Electrical Power System Digital Twin. Aerospace. https://doi.org/10.3390/aerospace11080688
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.