The DOI matches its Crossref record; 54 of the 54 references it cites were found in a registry or an index.
Additive Manufacturing of High-Entropy Alloys: A Review
Open accessAbstract
Owing to the reduced defects, low cost, and high efficiency, the additive manufacturing (AM) technique has attracted increasingly attention and has been applied in high-entropy alloys (HEAs) in recent years. It was found that AM-processed HEAs possess an optimized microstructure and improved mechanical properties. However, no report has been proposed to review the application of the AM method in preparing bulk HEAs. Hence, it is necessary to introduce AM-processed HEAs in terms of applications, microstructures, mechanical properties, and challenges to provide readers with fundamental understanding. Specifically, we reviewed (1) the application of AM methods in the fabrication of HEAs and (2) the post-heat treatment effect on the microstructural evolution and mechanical properties. Compared with the casting counterparts, AM-HEAs were found to have a superior yield strength and ductility as a consequence of the fine microstructure formed during the rapid solidification in the fabrication process. The post-treatment, such as high isostatic pressing (HIP), can further enhance their properties by removing the existing fabrication defects and residual stress in the AM-HEAs. Furthermore, the mechanical properties can be tuned by either reducing the pre-heating temperature to hinder the phase partitioning or modifying the composition of the HEA to stabilize the solid-solution phase or ductile intermetallic phase in AM materials. Moreover, the processing parameters, fabrication orientation, and scanning method can be optimized to further improve the mechanical performance of the as-built-HEAs.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Yeh, J. ‐., Chen, S. ‐., Lin, S. ‐., Gan, J. ‐., Chin, T. ‐., Shun, T. ‐., Tsau, C. ‐., & Chang, S. ‐. (2004) · Advanced Engineering Materials · doi:10.1002/adem.200300567 · Cited by 15,281
Self-citationMicrostructural development in equiatomic multicomponent alloys
Cantor, B., Chang, I. T. H., Knight, P., & Vincent, A. J. B. (2004) · Materials Science and Engineering: A · doi:10.1016/j.msea.2003.10.257 · Cited by 10,130
Microstructures and properties of high-entropy alloys
Zhang, Y., Zuo, T. T., Tang, Z., Gao, M. C., Dahmen, K. A., Liaw, P. K., & Lu, Z. P. (2014) · Progress in Materials Science · doi:10.1016/j.pmatsci.2013.10.001 · Cited by 7,128
Self-citationAdditive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Mechanical properties of Nb25Mo25Ta25W25 and V20Nb20Mo20Ta20W20 refractory high entropy alloys
Senkov, O. N., Wilks, G. B., Scott, J. M., & Miracle, D. B. (2011) · Intermetallics · doi:10.1016/j.intermet.2011.01.004 · Cited by 3,239
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
Refractory high-entropy alloys
Senkov, O. N., Wilks, G. B., Miracle, D. B., Chuang, C. P., & Liaw, P. K. (2010) · Intermetallics · doi:10.1016/j.intermet.2010.05.014 · Cited by 2,950
Self-citationAdditively manufactured hierarchical stainless steels with high strength and ductility
Wang, Y. M., Voisin, T., McKeown, J. T., Ye, J., Calta, N. P., Li, Z., Zeng, Z., Zhang, Y., Chen, W., Roehling, T. T., et al. (2018) · Nature Materials · doi:10.1038/nmat5021 · Cited by 2,613
Wu, Z., Bei, H., Pharr, G. M., & George, E. P. (2014) · Acta Materialia · doi:10.1016/j.actamat.2014.08.026 · Cited by 2,134
Microstructure and room temperature properties of a high-entropy TaNbHfZrTi alloy
Senkov, O. N., Scott, J. M., Senkova, S. V., Miracle, D. B., & Woodward, C. F. (2011) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2011.02.171 · Cited by 1,856
Cited by
Recent Advances on High‐Entropy Alloys for 3D Printing
Han, C., Fang, Q., Shi, Y., Tor, S. B., Chua, C. K., & Zhou, K. (2020) · Advanced Materials · doi:10.1002/adma.201903855 · Cited by 486
Additive manufacturing of high entropy alloys: A practical review
Ostovari Moghaddam, A., Shaburova, N. A., Samodurova, M. N., Abdollahzadeh, A., & Trofimov, E. A. (2021) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2020.11.029 · Cited by 474
A review on laser cladding of high-entropy alloys, their recent trends and potential applications
Arif, Z. U., Khalid, M. Y., ur Rehman, E., Ullah, S., Atif, M., & Tariq, A. (2021) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.06.041 · Cited by 334
Sing, S. L., Huang, S., Goh, G. D., Goh, G. L., Tey, C. F., Tan, J. H. K., & Yeong, W. Y. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100795 · Cited by 328
Metadata
- Authors
- Chen, S., Tong, Y., & Liaw, P. K.
- Venue
- Entropy
- Publisher
- MDPI AG
- Published
- 2018-12-06
- Volume
- 20
- Issue
- 12
- Pages
- 937
- ISSN
- 1099-4300 (ISSN-L)
- OpenAlex
- W2905405189
- Cited by
- 257
- References
- 54
- FWCI
- 10.55
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Additive Manufacturing of High-Entropy Alloys: A Review. https://app.cochat.ai/papers/10.3390/e20120937
- The paper
- Chen, S., Tong, Y., & Liaw, P. K. (2018). Additive Manufacturing of High-Entropy Alloys: A Review. Entropy. https://doi.org/10.3390/e20120937
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.