Spray Analysis and Combustion Assessment of Diesel-LPG Fuel Blends in Compression Ignition Engine
Open accessThe DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index.
Abstract
A major challenge for internal combustion engines (ICEs), and diesel engines, in particular, is the reduction of exhaust emissions, essentially nitrogen oxides (NOx) and particulate matter (PM). In this regard, the potential of LPG-diesel blends was evaluated in this work. The LPG and diesel blends were externally prepared by exploiting their perfect miscibility at high pressures. Two diesel-LPG mixtures with 20% and 35% by mass LPG concentrations were tested. In terms of spatial and temporal evolution, the spray characterization was performed for the two blends and pure diesel fuel through high-speed imaging technique. The combustion behavior, engine performance and exhaust emissions of LPG-diesel blends were evaluated through a test campaign carried out on a single-cylinder diesel engine. Diesel/LPG sprays penetrate less than pure diesel. This behavior results from a lower momentum, surface tension and viscosity, of the blend jets in comparison to diesel which guarantee greater atomization. The addition of LPG to diesel tends to proportionally increase the spray cone angle, due to the stronger turbulent flow interaction caused by, the lower density and low flash-boiling point. Because of improved atomization and mixing during the injection phase, the blends have shown great potential in reducing PM emissions, without affecting engine performance (CO2 emissions). The addition of LPG resulted in a significant smoke reduction (about 95%) with similar NOx emissions and acceptable THC and CO emissions. Furthermore, the low cetane number (CN) and high low-heating value (LHV) ensuring leaner air-fuel mixture, and improvements in terms of efficiency, particularly for a blend with a higher concentration of LPG.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures










Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Several gas-diesel mixtures have been studied to evaluate this performance under different engine speeds [141-143], reporting promising results regarding lower particulate emissions.”
From Biogas Production from Organic Wastes: Integrating Concepts of Circular Economy (2021) · cites this paper as [143]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Effect of ethanol–unleaded gasoline blends on engine performance and exhaust emission
Al-Hasan, M. (2003) · Energy Conversion and Management · doi:10.1016/s0196-8904(02)00166-8 · Cited by 561 · cited 1×
“It is probably caused by the LPG evaporation, which reduces the temperature in the combustion chamber [33], as well as, with the reduction of the combustion duration, there is less time for heat transfer losses.”
BackgroundWang, X., Huang, Z., Kuti, O. A., Zhang, W., & Nishida, K. (2010) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2010.03.006 · Cited by 326 · cited 1×
“Furthermore, a higher injection pressure does not involve significant variations for both parameters considered for DLPG blends, while for diesel an affect up to 400 μs is evident [29].”
BackgroundPapagiannakis, R. G., & Hountalas, D. T. (2003) · Applied Thermal Engineering · doi:10.1016/s1359-4311(02)00187-4 · Cited by 296 · cited 1×
“However, LPG can provide more flexibility for practical automotive applications as it is easier to manage in terms of storage and it can be stored in a liquid state at a pressure relatively lower than that of natural gas [15].”
BackgroundCombustion characteristics and emissions of Fischer–Tropsch diesel fuels in IC engines
Gill, S. S., Tsolakis, A., Dearn, K. D., & Rodríguez-Fernández, J. (2011) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2010.09.001 · Cited by 277 · cited 1×
“(LPG)-diesel blends, thus exploiting the potential of such fuel, such as high efficiency and low emission values of nitrogen oxides (NOx) and particulate matter (PM) [5].”
BackgroundKim, K., Kim, D., Jung, Y., & Bae, C. (2013) · Fuel · doi:10.1016/j.fuel.2013.02.060 · Cited by 139 · cited 2×
“This behaviour results from a lower momentum of the jet, due to the lower density of the blends than diesel [26], and from lower surface tension and viscosity, which guarantee greater atomization [27].”
BackgroundPark, S. H., Kim, H. J., Suh, H. K., & Lee, C. S. (2009) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2009.07.002 · Cited by 120 · cited 2×
“entrainment and the decrease of the droplets’ momentum [25].”
BackgroundMacroscopic diesel fuel spray shadowgraphy using high speed digital imaging in a high pressure cell
Klein-Douwel, R. J. H., Frijters, P. J. M., Somers, B., de Boer, W. A., & Baert, R. S. G. (2006) · Fuel · doi:10.1016/j.fuel.2006.11.039 · Cited by 107 · cited 1×
“The spray evolution was characterized by high-speed shadowgraph imaging [21].”
MethodSpray and evaporation characteristics of n-pentanol–diesel blends in a constant volume chamber
Ma, Y., Huang, S., Huang, R., Zhang, Y., & Xu, S. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2016.10.063 · Cited by 101 · cited 1×
“This behaviour results from a lower momentum of the jet, due to the lower density of the blends than diesel [26], and from lower surface tension and viscosity, which guarantee greater atomization [27].”
BackgroundBlasio, G. D., Belgiorno, G., & Beatrice, C. (2017) · Applied Energy · doi:10.1016/j.apenergy.2017.07.103 · Cited by 100 · cited 3×
“f li t t t a single-cylinder CI engine [19] derived from a multi-cylinder engine whose cylinder head has been suitably modified.”
MethodInfluentialQi, D., Bian, Y., Ma, Z. Y., Zhang, C. H., & Liu, S. Q. (2006) · Energy Conversion and Management · doi:10.1016/j.enconman.2006.06.013 · Cited by 83
Litzinger, T., Stoner, M. A., Hess, H. S., & Boehman, A. L. (2000) · International Journal of Engine Research · doi:10.1243/1468087001545263 · Cited by 78 · cited 3×
“bustion efficiency (see the HRR pilot combustion in Figure 6) because of overmixing conditions, it leads to over-lean regions [23,24].”
BackgroundLi, C., Yin, L., Shamun, S., Tunér, M., Johansson, B., Solsjö, R., & Bai, X. (2016) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2016-01-0767 · Cited by 69 · cited 1×
“In fact, because of a higher ignition delay (a lower heat of vaporization and cetane number), a greater fuel mass is trapped in the crevices volumes compared to diesel combustion, justifying this efficiency reduction [31,32].”
BackgroundMyung, C.-L., Lee, H. J., Choi, K.-K., Lee, Y. J., & Park, S. (2009) · International Journal of Automotive Technology · doi:10.1007/s12239-009-0062-9 · Cited by 68 · cited 1×
“Furthermore, it guarantees a cooling effect of the combustion chamber thanks to evaporation’s latent heat, which allows to increase the power and decrease the exhaust emissions [16].”
BackgroundBelgiorno, G., Boscolo, A., Dileo, G., Numidi, F., Pesce, F. C., Vassallo, A. L., Ianniello, R., Beatrice, C., & Blasio, G. D. (2020) · SAE International Journal of Advances and Current Practices in Mobility · doi:10.4271/2020-37-0003 · Cited by 64 · cited 1×
“As is known, up to 2015 the optimization of piston bowl [1], intake ports, EGR, turbocharger [2] and fuel injection system [3] was mainly directed to increase performance [4], reaching important milestones.”
MethodSelf-citationPirouzpanah, V., & Kashani, B. O. (1999) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/1999-01-0841 · Cited by 56 · cited 1×
“The use of natural gas mixed with diesel is a valid alternative to LPG [14].”
BackgroundBlasio, G. D., Beatrice, C., Belgiorno, G., Pesce, F. C., & Vassallo, A. L. (2017) · SAE International Journal of Engines · doi:10.4271/2017-24-0072 · Cited by 45 · cited 1×
“As is known, up to 2015 the optimization of piston bowl [1], intake ports, EGR, turbocharger [2] and fuel injection system [3] was mainly directed to increase performance [4], reaching important milestones.”
MethodBeatrice, C., Denbratt, I., Blasio, G. D., Luca, G. D., Ianniello, R., & Saccullo, M. (2020) · Applied Sciences · doi:10.3390/app10207182 · Cited by 41 · cited 3×
“ls , t e cali rati setti s ( level, ener i i ti i a n er of the pulses, s irl r ti ) r e i - l t i l t i i r indicating system, which process in real-time the net HRR [10].”
BackgroundMethodSelf-citationMacroscopic spray characteristics of wide distillation fuel (WDF)
Yu, W., Yang, W., Mohan, B., Tay, K. L., & Zhao, F. (2015) · Applied Energy · doi:10.1016/j.apenergy.2015.12.051 · Cited by 39 · cited 2×
“crease because of higher spray momentum and lower drag forces [28].”
BackgroundBlasio, G. D., Beatrice, C., Ianniello, R., Pesce, F. C., Vassallo, A. L., Belgiorno, G., & Avolio, G. (2019) · SAE International Journal of Advances and Current Practices in Mobility · doi:10.4271/2019-24-0111 · Cited by 39 · cited 1×
“As is known, up to 2015 the optimization of piston bowl [1], intake ports, EGR, turbocharger [2] and fuel injection system [3] was mainly directed to increase performance [4], reaching important milestones.”
MethodSelf-citationDijkstra, R., Blasio, G. D., Boot, M. D., Beatrice, C., & Bertoli, C. (2011) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2011-24-0053 · Cited by 33 · cited 3×
“bustion efficiency (see the HRR pilot combustion in Figure 6) because of overmixing conditions, it leads to over-lean regions [23,24].”
BackgroundMa, Z., Huang, Z., Li, C., Wang, X., & Miao, H. (2007) · Energy & Fuels · doi:10.1021/ef060574a · Cited by 27 · cited 1×
“Therefore, the use of mixed blends, with miscible fuels characterized by different thermodynamic properties, is of practical and fundamental importance [12,13].”
BackgroundThe effects of fuel–air mixing and injector dribble on diesel unburned hydrocarbon emissions
Koci, C. P., Fitzgerald, R. P., Ikonomou, V., & Sun, K. (2019) · International Journal of Engine Research · doi:10.1177/1468087418821827 · Cited by 26 · cited 1×
“This leads to a greater fuel mass trapped in the crevices volumes, as discussed previously, and an excessive mixing, creating very lean-regions, thus not guaranteeing complete combustion due to low temperatures and increasing in unburnt emissions [36].”
BackgroundComparative investigation of diesel and mixed liquefied petroleum gas/diesel injection engines
Cao, J., Bian, Y., Qi, D., Cheng, Q., & Wu, T. S. (2004) · Proceedings of the Institution of Mechanical Engineers Part D Journal of Automobile Engineering · doi:10.1243/095440704774061219 · Cited by 24 · cited 1×
“[9] conducted engine and spray tests using the blends with different LPG percentages.”
MethodOn the Theoretical Prediction of Fuel Droplet Size Distribution in Nonreactive Diesel Sprays
Cao, J. (2001) · Journal of Fluids Engineering · doi:10.1115/1.1445140 · Cited by 19 · cited 1×
“These phenomena cause a considerable decrease in both the average number of droplets and a different redistribution [11].”
BackgroundCombustion and emission characteristics of a diesel engine fuelled with diesel–propane blends
Ma, Z., Huang, Z., Li, C., Wang, X., & Miao, H. (2007) · Fuel · doi:10.1016/j.fuel.2007.09.011 · Cited by 19 · cited 1×
“Therefore, the use of mixed blends, with miscible fuels characterized by different thermodynamic properties, is of practical and fundamental importance [12,13].”
BackgroundKey Fuel Injection System Features for Efficiency Improvement in Future Diesel Passenger Cars
Beatrice, C., Blasio, G. D., Pesce, F. C., Vassallo, A. L., Avolio, G., & Ianniello, R. (2019) · SAE International Journal of Advances and Current Practices in Mobility · doi:10.4271/2019-01-0547 · Cited by 19 · cited 1×
“As already highlighted above, a shorter CA90-10 (combustion duration) and a better fuel distribution justify these improvements [34,35].”
BackgroundSelf-citationDiwakar, R., & Domenech, V. (2017) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2017-01-0566 · Cited by 13 · cited 1×
“As already highlighted above, a shorter CA90-10 (combustion duration) and a better fuel distribution justify these improvements [34,35].”
BackgroundThe New BMW Six-cylinder Top Engine with Innovative Turbocharging Concept
Steinparzer, F., Nefischer, P., Hiemesch, D., & Rechberger, E. (2016) · MTZ worldwide · doi:10.1007/s38313-016-0104-4 · Cited by 13 · cited 1×
“As is known, up to 2015 the optimization of piston bowl [1], intake ports, EGR, turbocharger [2] and fuel injection system [3] was mainly directed to increase performance [4], reaching important milestones.”
MethodDong-hui, Q., Longbao, Z., & Shenghua, L. (2005) · Proceedings of the Institution of Mechanical Engineers Part D Journal of Automobile Engineering · doi:10.1243/095440705x5920 · Cited by 11 · cited 1×
“[8] using an LPG / diesel blend observed longer ignition delays, resulting in better air-fuel mixing and reduced soot emissions, but a worsening efficiency and HC emissions.”
MethodImage processing of vaporizing GDI sprays: a new curvature-based approach
Lazzaro, M., & Ianniello, R. (2017) · Measurement Science and Technology · doi:10.1088/1361-6501/aa9301 · Cited by 11 · cited 2×
“To objectively evaluate the spray evolution for liquid/vapour phases, a customized algorithm developed in MATLAB® [22] was employed, capable of defining the spray’s macroscopic parameters, i.”
MethodSelf-citationCharacterization of Combustion and Emissions of a Propane-Diesel Blend in a Research Diesel Engine
Cardone, M., Mancaruso, E., Marialto, R., Sequino, L., & Vaglieco, B. M. (2016) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2016-01-0810 · Cited by 10 · cited 1×
“Based on the preliminary analysis on the use of LPG/Diesel blends [17,18], the present work focuses on studying the fuel-engine interaction to evaluate the effects of blends on engine outputs, with particular attention to the combustion process and pollutant emissions.”
BackgroundSelf-citationCombustion and Emission Characteristics of a Diesel Engine Fuelled with Diesel-LPG Blends
Marialto, R., Sequino, L., Blasio, G. D., Cardone, M., Beatrice, C., Ianniello, R., & Fontana, G. (2019) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2019-24-0038 · Cited by 8 · cited 7×
“Likewise, by increasing the LPG mass percentage, the LHV (Low-Heating Value) and the heat of vaporization of the blend increase [18].”
BackgroundMethodSelf-citationLee, S. W., Cho, Y. S., Choi, W., Lee, J. H., & Park, Y. J. (2012) · International Journal of Automotive Technology · doi:10.1007/s12239-012-0118-0 · Cited by 7 · cited 3×
“The addition of LPG to diesel tends to proportionally increase the spray cone angle, due to the stronger turbulent flow interaction caused by a lower density and LPG vaporizing shortly after injection because of its low flash-boiling point [6].”
BackgroundInfluentialInvestigation of Premixed and Diffusion Flames in PPC and CI Combustion Modes
An, Y., Ali, M. J. M., Vallinayagam, R., Vedharaj, S., Pérez, F. E. H., Sim, J., Chang, J., Im, H. G., & Johansson, B. (2018) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2018-01-0899 · Cited by 2 · cited 1×
“The combustion then moves from a diffusive mode, typical for diesel fuel, to a more premixed one, as evidenced by a reduced combustion duration [30].”
Background
Research works printed but not linked: 1
- Heywood, J.B. (1988). Internal Combustion Engine Fundamentals, McGraw-Hill.
Cited by
Biogas Production from Organic Wastes: Integrating Concepts of Circular Economy
Ellacuriaga, M., García-Cascallana, J., & Gómez, X. (2021) · Fuels · doi:10.3390/fuels2020009 · Cited by 126
Lubricity of Ethanol–Diesel Fuel Blends—Study with the Four-Ball Machine Method
Kuszewski, H., Jaworski, A., & Mądziel, M. (2021) · Materials · doi:10.3390/ma14102492 · Cited by 18
Consequence Analysis of LPG-Related Hazards: Ensuring Safe Transitions to Cleaner Energy
Ardila-Suárez, C., Lacoursière, J. P., Soucy, G., & de Vasconcelos, B. R. (2025) · Fuels · doi:10.3390/fuels6020045 · Cited by 16
Elkelawy, M., Mohamad, H. A. E., elhamid, E. A., & El-Gamal, M. (2022) · Journal of Engineering Research - Egypt/Journal of Engineering Research · doi:10.21608/erjeng.2022.168050.1108 · Cited by 14
Metadata
- Authors
- Cardone, M., Marialto, R., Ianniello, R., Lazzaro, M., & Di Blasio, G.
- Affiliations
- University of Naples Federico II (IT)
- National Research Council (IT)
- CNR–STEMS, Viale Marconi, 4, 80125 Naples, Italy
- Corresponding author
- Marialto, Renato
- Venue
- Fuels
- Publisher
- MDPI AG
- Published
- 2020-12-31
- Volume
- 2
- Issue
- 1
- Pages
- 1-15
- ISSN
- 2673-3994 (ISSN-L)
- OpenAlex
- W3118173698
- Cited by
- 15
- References
- 34
- Citations by year
- 2026: 2 · 2025: 3 · 2023: 4 · 2022: 4 · 2021: 2
- FWCI
- 1.19
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Fuels (publishedVersion, cc-by)
- Topics
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Advanced Combustion Engine Technologies
- Physical Sciences › Engineering › Automotive Engineering › Engine and Fuel Emissions
- Physical Sciences › Energy › Fuel Technology › Biodiesel Production and Applications
- Keywords
- spray characterization, atomization, spray angle, combustion characteristics, vehicle emissions, particulate matter reduction, NOx emissions, high-speed imaging, compression ignition engine, cetane number, lower heating value, engine efficiency
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.