Resorcinol–Formaldehyde-Derived Carbon Xerogels: Preparation, Functionalization, and Application Aspects
Open accessThe DOI matches its Crossref record; 161 of the 161 references it cites were found in a registry or an index.
Abstract
Carbon xerogels (CXs) are materials obtained via the pyrolysis of resins prepared via the sol–gel polycondensation of resorcinol and formaldehyde. These materials attract great attention as adsorbents, catalyst supports, and energy storage materials. One of the most interesting features of CXs is the possibility of fine-tuning their structures and textures by changing the synthesis conditions in the sol–gel stage. Thus, the first part of this review is devoted to the processes taking place in the polycondensation stage of organic precursors. The formation of hydroxymethyl derivatives of resorcinol and their polycondensation take place at this stage. Both of these processes are catalyzed by acids or bases. It is revealed that the sol–gel synthesis conditions, such as pH, the formaldehyde/resorcinol ratio, concentration, and the type of basic modifier, all affect the texture of the materials being prepared. The variation in these parameters allows one to obtain CXs with pore sizes ranging from 2–3 nm to 100–200 nm. The possibility of using other precursors for the preparation of organic aerogels is examined as well. For instance, if phenol is used instead of resorcinol, the capabilities of the sol–gel method become rather limited. At the same time, other phenolic compounds can be applied with great efficiency. The methods of gel drying and the pyrolysis conditions are also reviewed. Another important aspect analyzed within this review is the surface modification of CXs by introducing various functional groups and heteroatoms. It is shown that compounds containing nitrogen, sulfur, boron, or phosphorus can be introduced at the polycondensation stage to incorporate these elements into the gel structure. Thus, the highest surface amount of nitrogen (6–11 at%) was achieved in the case of the polycondensation of formaldehyde with melamine and hydroxyaniline. Finally, the methods of preparing metal-doped CXs are overviewed. Special attention is paid to the introduction of a metal precursor in the gelation step. The elements of the iron subgroup (Fe, Ni, Co) were found to catalyze carbon graphitization. Therefore, their introduction can be useful for enhancing the electrochemical properties of CXs. However, since the metal surface is often covered by carbon, such materials are poorly applicable to conventional catalytic processes. In summary, the applications of CXs and metal-doped CXs are briefly mentioned. Among the promising application areas, Li-ion batteries, supercapacitors, fuel cells, and adsorbents are of special interest.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures
![Figure 10 Ranges of SSA values for the metal-doped CXs reported by Sun et al. (Co/CX) [110], Abidin et al. (Co/CX) [111], Skowronski and Osinska (Ni/CX) [112], El-Jemni et al. (Ni/CX) [113], Job et al. (Ni/CX) [114], Barranco-Lopez et al. (Fe/CX) [115], and Ptaszkowska-Koniarz et al. (Cu/CX) [116].](https://figures.cochat.ai/paper-figures/d982306d454844e3b68bcf4e60174fb6/resorcinolformaldehyde-derived-carbon-xerogels-preparation-functionalization-and-figure-10.jpg)




![Figure 5 Effects of pH on the SSA values of CXs reported by Lin and Ritter [32], Rey-Raap et al. [34], and Zubizaretta et al. [35].](https://figures.cochat.ai/paper-figures/b222bc58d46e4488b7969792f062608c/resorcinolformaldehyde-derived-carbon-xerogels-preparation-functionalization-and-figure-5.jpg)

![Figure 7 Effects of the pyrolysis temperature on the SSA values reported by Moreno et al. [61] and Lin et al. [62].](https://figures.cochat.ai/paper-figures/68127a7018ac49d4b5b87c8e6a76b014/resorcinolformaldehyde-derived-carbon-xerogels-preparation-functionalization-and-figure-7.jpg)
![Figure 8 Relative surface area (SSA/SSA0) of the CXs: (a) activated by KOH; (b) activated by CO2. The SSA values were calculated from the data reported by Zubizaretta et al. [35], Chavhan et al. [40], and Lin et al. [62].](https://figures.cochat.ai/paper-figures/8978108a484e47e3b8a917b253a3a2dd/resorcinolformaldehyde-derived-carbon-xerogels-preparation-functionalization-and-figure-8.jpg)


Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Traditional carbon aerogels are synthesized via the sol-gel polymerization of phenol/resorcinol and formaldehyde, followed by solvent exchange, drying, and hightemperature pyrolysis 14,15 .”
From Boosting hydrogen production with raspberry-derived carbon aerogels with in situ grown carbon nanotubes (2026) · cites this paper as [14]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Hench, L. L., & West, J. K. (1990) · Chemical Reviews · doi:10.1021/cr00099a003 · Cited by 4,450
KOH activation of carbon-based materials for energy storage
Wang, J., & Kaskel, S. (2012) · Journal of Materials Chemistry · doi:10.1039/c2jm34066f · Cited by 2,726
Recent Progress in the Synthesis of Porous Carbon Materials
Lee, J., Kim, J., & Hyeon, T. (2006) · Advanced Materials · doi:10.1002/adma.200501576 · Cited by 2,127
Organic aerogels from the polycondensation of resorcinol with formaldehyde
Pekala, R. W. (1989) · Journal of Materials Science · doi:10.1007/bf01139044 · Cited by 1,811
Hulicova‐Jurcakova, D., Seredych, M., Lu, G. Q., & Bandosz, T. J. (2009) · Advanced Functional Materials · doi:10.1002/adfm.200801236 · Cited by 1,672
Synthesis of mesoporous silica nanoparticles
Wu, S.-H., Mou, C.-Y., & Lin, H.-P. (2013) · Chemical Society Reviews · doi:10.1039/c3cs35405a · Cited by 1,571
Yang, X., Wan, Y., Zheng, Y., He, F., Yu, Z., Huang, J., Wang, H., Ok, Y. S., Jiang, Y., & Gao, B. (2019) · Chemical Engineering Journal · doi:10.1016/j.cej.2019.02.119 · Cited by 1,527
Preparation and Properties of Resorcinol–Formaldehyde Organic and Carbon Gels
Al‐Muhtaseb, S. A., & Ritter, J. A. (2003) · Advanced Materials · doi:10.1002/adma.200390020 · Cited by 1,023
New Strategies for Novel MOF-Derived Carbon Materials Based on Nanoarchitectures
Wang, C., Kim, J., Tang, J., Kim, M., Lim, H., Malgras, V., You, J., Xu, Q., Li, J., & Yamauchi, Y. (2020) · Chem · doi:10.1016/j.chempr.2019.09.005 · Cited by 784
Nitrogen-containing porous carbons: synthesis and application
Shen, W., & Fan, W. (2013) · J. Mater. Chem. A · doi:10.1039/c2ta00028h · Cited by 698
Research works printed but not linked: 1
- Taher Hcine, G. (2017). Porosity, IntechOpen. Chapter 3.
Cited by
Parvin, N., Merum, D., Kang, M., Joo, S. W., Jung, J. H., & Mandal, T. K. (2025) · Journal of Materials Chemistry A · doi:10.1039/d5ta02887f · Cited by 147
An Overview of Recycling Phenolic Resin
Zhu, B. C., Jiang, X., Li, S., & Zhu, M. (2024) · Polymers · doi:10.3390/polym16091255 · Cited by 44
Recent advances in electrode materials for high-performance supercapacitor applications
Raghav, J., Raghav, S., Chavda, V., Diksha, K., Sakshi, K., Singh, S., Pandey, V. S., Jain, P., & Kumar, D. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.120016 · Cited by 40
Islam, M. S., Kundu, S., Samsunnahar, M., Khandaker, T., Ibrahim, A. B. M., Anik, M. A.-A. M., Hasan, M. K., & Hossain, M. S. (2025) · Materials Advances · doi:10.1039/d5ma00786k · Cited by 27
Wang, X., Gao, Q., Zhou, Y., & Wang, Z. (2025) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2025.178668 · Cited by 22
Dry Gels: Concept, Current Trends, and New Avenues in Drug Delivery and Biomedical Application
Boruah, M., & Sarma, A. (2025) · Advanced Healthcare Materials · doi:10.1002/adhm.202500863 · Cited by 18
Recent Progress on Non‑Biomass Carbon‑Based Anodes for Sodium‑Ion Batteries
Ansar, M., Li, C., Hassan, M., Liu, Q., He, W., Hussain, W., LI, L., Chen, R., & Wu, F. (2026) · Advanced Energy Materials · doi:10.1002/aenm.70769 · Cited by 10
Synthesis of Ni-Doped Graphene Aerogels for Electrochemical Applications
Gónzález-Barriuso, M., Sánchez-Suárez, M., González-Lavín, J., Arenillas, A., & Rey‐Raap, N. (2024) · Gels · doi:10.3390/gels10030180 · Cited by 10
N/P co-doped cellulose carbon aerogel with enhanced supercapacitance
Wang, X., Gao, Q., Zhou, Y., & Wang, Z. (2025) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2025.130458 · Cited by 6
Ramírez-Valencia, L. D., Bailón‐García, E., -Rodríguez, A. I. M., Carrasco-Marín, F., & Pérez‐Cadenas, A. F. (2025) · Journal of Power Sources · doi:10.1016/j.jpowsour.2025.237189 · Cited by 6
Gaikwad, M. A., Pappu, S., Pathak, A. D., Sharma, C., & Kumta, P. N. (2026) · Journal of Power Sources · doi:10.1016/j.jpowsour.2026.239254 · Cited by 6
François, M., Lin, K., Hussain, J., Mdlovu, N. V., Chen, C.-J., & Sie, P.-J. (2026) · Journal of the Taiwan Institute of Chemical Engineers · doi:10.1016/j.jtice.2026.106812 · Cited by 5
Hydrogenation of 1,3-Butadiene over Nickel-Containing Carbon Xerogels
Veselov, G. B., Shubin, Y. V., & Vedyagin, A. A. (2024) · Kinetics and Catalysis · doi:10.1134/s0023158424601773 · Cited by 5
Self-citationAmaro‐Gahete, J., Ortiz-Ramos, U., Benítez, A., Torres, W. R., Bailón‐García, E., Carrasco-Marín, F., & Tesio, Á. Y. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.117884 · Cited by 5
Eltaher, K., AbdElhafez, S. E., Ali, R. M., El-Faham, A., El‐Bardan, A. A., & Hamad, H. A. F. (2026) · Scientific Reports · doi:10.1038/s41598-026-35236-8 · Cited by 4
Veselov, G. B., Afonnikova, S. D., Mishakov, I. V., & Vedyagin, A. A. (2025) · Composites Communications · doi:10.1016/j.coco.2025.102290 · Cited by 4
Self-citationSalem, O. M., & Mohamed, F. (2025) · International Journal of Environmental Science and Technology · doi:10.1007/s13762-025-06932-1 · Cited by 3
pH-Controlled Synthesis of Carbon Xerogels for Coin-Type Organic Supercapacitor Electrodes
Jung, J. C., & Jung, W. (2023) · Korean Journal of Materials Research · doi:10.3740/mrsk.2023.33.10.430 · Cited by 3
Structural modification of CNT-C xerogel through synthesis parameters
Tabrizi, N. S., & Yavari, M. (2024) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2024.113260 · Cited by 3
Adsorption of Reactive Blue 13 from Dyeing Wastewater onto Mesoporous Carbon Xerogels
Lu, H., Zhu, J., Li, D., Liu, J., Yao, R., & Yao, M. (2024) · Polish Journal of Environmental Studies · doi:10.15244/pjoes/183565 · Cited by 2
Khamkure, S., Gamero-Melo, P., Reyes-Rosas, A., Zermeño-González, A., Cruz, J. L. Á., Albiter, E., Chávez, G., & Terrones, V. B. (2025) · Gels · doi:10.3390/gels11050323 · Cited by 2
Gao, X., Sun, K., Peng, H., & Ma, G. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2025.120285 · Cited by 2
Choi, H., Parale, V. G., kim, T., Kim, J., Bhosale, S. B., Kim, S.-H., Phadtare, V. D., Kim, Y., Lee, W., Mali, M. G., et al. (2026) · Energy · doi:10.1016/j.energy.2026.140404 · Cited by 2
Chettiannan, B., Muniappan, E., Maninathan, I., Rajendran, R., Qian, Z., Li, J. Q., & Sangaraju, S. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.123393 · Cited by 2
Nano- and micro-fabricated materials and technologies for propulsion systems of small satellites
Levchenko, I., ̃Riccardi, C., Roman, H. E., Pedrini, D., Baranov, O., Cvelbar, U., Xu, S., Keidar, M., & Alexander, K. (2026) · Acta Astronautica · doi:10.1016/j.actaastro.2026.07.002 · Cited by 2
Rubalcaba-Medina, A., Rodríguez-Macias, F. J., Sanchez-Mendoza, Y. A., Jiménez-Salinas, S., Rafei, M., Gracia-Espino, E., & Vega-Cantu, Y. I. (2026) · Energy Advances · doi:10.1039/d5ya00133a · Cited by 1
Veselov, G. B., Shubin, Y. V., Plyusnin, P. E., & Vedyagin, A. A. (2025) · Journal of Sol-Gel Science and Technology · doi:10.1007/s10971-025-06719-3 · Cited by 1
Self-citationSynthesis and Characterization of Carbon Aerogel by Freeze-Drying Method
Li, J. Y., Bao, T., Li, Y. Y., Bolag, A., Tian, X. Q., & Tegus, O. (2025) · Materials science forum · doi:10.4028/p-gej4mh · Cited by 1
Delgado-Martín, G., Domínguez, M. I., T, L. M. M., & Centeno, M. Á. (2025) · Diamond and Related Materials · doi:10.1016/j.diamond.2025.113125 · Cited by 1
Médina, O. E., López, D., Amell, A. A., & Santamaría, A. (2026) · Applied Materials Today · doi:10.1016/j.apmt.2026.103122 · Cited by 1
Najeh, I., Ahmed, W., Hjiri, M., & Mir, L. E. (2026) · Physica B Condensed Matter · doi:10.1016/j.physb.2026.418377 · Cited by 1
Medhavi, A., Singh, V. K., Sharma, U. K., & Singh, S. P. (2025) · Energy Storage · doi:10.1002/est2.70141
Veselov, G. B., Shubin, Y. V., & Vedyagin, A. A. (2025) · Journal of Non-Crystalline Solids · doi:10.1016/j.jnoncrysol.2025.123487
Self-citationMokhtar, A. M., Mahmoud, R., Allah, A. E., Mahgoub, S. M., & Mohamed, F. M. (2025) · Journal of Porous Materials · doi:10.1007/s10934-025-01823-9
Xiao, Y., Dong, S., Zhang, S., Hu, J., & Luo, Y. (2025) · Journal of Porous Materials · doi:10.1007/s10934-025-01835-5
Immobilized Nostoc sp. on biopolymers for enhanced CO₂ photoconversion
Zapata, K., Viveros, F. E., Galeano-Caro, D., Médina, O. E., Pérez‐Cadenas, A. F., Carrasco-Marín, F., Rojano, B. A., Franco, C. A., & Cortés, F. B. (2025) · Molecular Catalysis · doi:10.1016/j.mcat.2025.115571
Wáng, Y. X. J., Yang, M., Liu, Y., Chen, L., Wang, X., Li, Y., Qiu, S., Shi, H., Ma, X., Yi, Y., et al. (2026) · Materials Today Chemistry · doi:10.1016/j.mtchem.2026.103508
Kurian, M., Amin, S., Pandikassala, A., Manoj, M., Vijayan, J., Krishnamurty, S., & Kurungot, S. (2026) · Batteries & Supercaps · doi:10.1002/batt.70336
In search of a simple way to functionalize carbon nanofibers with nitrogen
Maksimova, T. A., Kuts, M. G., Ananina, A. A., Nartova, A. V., Shlyapin, D. A., Shelepova, E. V., Bauman, Y. I., Mishakov, I. V., & Vedyagin, A. A. (2026) · Surfaces and Interfaces · doi:10.1016/j.surfin.2026.109690
Self-citationBoldrin, F. H. C., da Silva, B. H. B., Mascarenhas, C. G., Lico, C. A. F. M. D. P., Andrade, M. A. P., Pereira, P., Yu, L., Lanza, M. R. D. V., & Rodrigues, L. Á. (2026) · Materials Science in Semiconductor Processing · doi:10.1016/j.mssp.2026.110979
Balbin-Córdoba, L. D., Vanegas-Ramirez, J., Marín, L., Rodríguez, L. A., Magén, C., Tabares, J. A., Manotas-Albor, M., Visbal, R., & Mora, M. (2026) · Nanomaterials · doi:10.3390/nano16171068
BELGUESMI, A., Souilah, A., Gharsallah, A., García‐Bernabé, A., Fattoum, A., Arous, M., & Elaloui, E. (2026) · Journal of Sol-Gel Science and Technology · doi:10.1007/s10971-026-07234-9
Nguyen, L. H., Nguyen, N. D. Y., Nguyen, N. N. Q., Nguyen, P. T. N., Le, T. T. T., Do, K. T., Truong, T. Q., Chu, V. V. L., Nguyen, D. P. T., Do, S. T. A., et al. (2026) · Diamond and Related Materials · doi:10.1016/j.diamond.2026.114252
Asim, M., Samancı, M., Hussain, A., Janjua, N. K., & Yurtcan, A. B. (2026) · Journal of Solid State Chemistry · doi:10.1016/j.jssc.2026.126371
Pan, X.-X., Zhao, Y., Supiyeva, Z., & Abbas, Q. (2026) · Frontiers in Chemistry · doi:10.3389/fchem.2026.1951078
Cherian, S. K., Tewatia, S., Sarada, B. V., & Sharma, C. S. (2026) · Journal of Power Sources · doi:10.1016/j.jpowsour.2026.241689
Sun, H., Li, J., Gao, Y., Liu, T., Wang, H., Xu, W., & Zhang, H. (2026) · Langmuir · doi:10.1021/acs.langmuir.6c04300
Martínez-Díaz, E., Arenillas, A., & Rey‐Raap, N. (2026) · IntechOpen eBooks · doi:10.5772/intechopen.1017700
An investigation into sustainable carbon aerogels derived from lignin and polyvinyl alcohol
Leela, V., Babu, J., Joseph, M., Joseph, J., Kachirayil, A. J., Thomas, B., Mukundan, M. K., & Raveendran, R. (2026) · Sadhana · doi:10.1007/s12046-026-03425-w
Metadata
- Authors
- Veselov, G., & Vedyagin, A.
- Affiliations
- Boreskov Institute of Catalysis (RU)
- Corresponding author
- Vedyagin, Aleksey
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2023-10-05
- Volume
- 16
- Issue
- 19
- Pages
- 6566
- ISSN
- 1996-1944 (ISSN-L)
- PMC
- PMC10573919
- OpenAlex
- W4387405841
- Cited by
- 48
- References
- 160
- Citations by year
- 2026: 22 · 2025: 20 · 2024: 5 · 2023: 1
- FWCI
- 1.44
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Materials (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Funders
- Ministry of Science and Higher Education of the Russian Federation (AAAA-A21-121011390054-1)
- Topics
- Physical Sciences › Materials Science › Materials Chemistry › Aerogels and thermal insulation
- Physical Sciences › Materials Science › Materials Chemistry › Mesoporous Materials and Catalysis
- Physical Sciences › Chemistry › Physical and Theoretical Chemistry › Adsorption, diffusion, and thermodynamic properties of materials
- Keywords
- carbon xerogels, resorcinol-formaldehyde, sol-gel polycondensation, gel drying, pyrolysis, surface functionalization, heteroatom doping, nitrogen doping, iron catalysts, carbon graphitization, lithium-ion batteries, supercapacitors
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.