The DOI matches its Crossref record; 21 of the 21 references it cites were found in a registry or an index.
From Powders to Dense Metal Parts: Characterization of a Commercial AlSiMg Alloy Processed through Direct Metal Laser Sintering
Open accessAbstract
In this paper, a characterization of an AlSiMg alloy processed by direct metal laser sintering (DMLS) is presented, from the analysis of the starting powders, in terms of size, morphology and chemical composition, through to the evaluation of mechanical and microstructural properties of specimens built along different orientations parallel and perpendicular to the powder deposition plane. With respect to a similar aluminum alloy as-fabricated, a higher yield strength of about 40% due to the very fine microstructure, closely related to the mechanisms involved in this additive process is observed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
Properties and Selection: Nonferrous Alloys and Special-Purpose Materials
(1990) · ASM International eBooks · doi:10.31399/asm.hb.v02.9781627081627 · Cited by 2,624
Consolidation phenomena in laser and powder-bed based layered manufacturing
Kruth, J.-P., Levy, G., Klocke, F., & Childs, T. H. C. (2007) · CIRP Annals · doi:10.1016/j.cirp.2007.10.004 · Cited by 1,444
Binding mechanisms in selective laser sintering and selective laser melting
Kruth, J., Mercelis, P., Van Vaerenbergh, J., Froyen, L., & Rombouts, M. (2005) · Rapid Prototyping Journal · doi:10.1108/13552540510573365 · Cited by 1,383
Brandl, E., Heckenberger, U., Holzinger, V., & Buchbinder, D. (2012) · Materials & Design · doi:10.1016/j.matdes.2011.07.067 · Cited by 1,151
Rapid manufacturing of metal components by laser forming
Santos, E. C., Shiomi, M., Osakada, K., & Laoui, T. (2006) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.09.005 · Cited by 740
Rapid Manufacturing: An Industrial Revolution for the Digital Age
(2005) · Wiley eBooks · doi:10.1002/0470033991 · Cited by 679
High Power Selective Laser Melting (HP SLM) of Aluminum Parts
Buchbinder, D., Schleifenbaum, H., Heidrich, S., Meiners, W., & Bültmann, J. (2011) · Physics Procedia · doi:10.1016/j.phpro.2011.03.035 · Cited by 666
Economics of additive manufacturing for end-usable metal parts
Atzeni, E., & Salmi, A. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3878-1 · Cited by 630
Self-citationDirect laser sintering of metal powders: Mechanism, kinetics and microstructural features
Simchi, A. (2006) · Materials Science and Engineering: A · doi:10.1016/j.msea.2006.04.117 · Cited by 590
Cited by
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Metal Additive Manufacturing: A Review of Mechanical Properties
Lewandowski, J. J., & Seifi, M. (2016) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070115-032024 · Cited by 1,722
Li, W., Li, S., Liu, J., Zhang, A., Zhou, Y., Wei, Q., Yan, C., & Shi, Y. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2016.03.088 · Cited by 850
Additively manufactured carbon fiber-reinforced composites: State of the art and perspective
van de Werken, N., Tekinalp, H., Khanbolouki, P., Ozcan, S., Williams, A., & Tehrani, M. (2020) · Additive Manufacturing · doi:10.1016/j.addma.2019.100962 · Cited by 566
Trevisan, F., Calignano, F., Lorusso, M., Pakkanen, J., Aversa, A., Ambrosio, E., Lombardi, M., Fino, P., & Manfredi, D. (2017) · Materials · doi:10.3390/ma10010076 · Cited by 502
Self-citation
Metadata
- Authors
- Manfredi, D., Calignano, F., Krishnan, M., Canali, R., Ambrosio, E., & Atzeni, E.
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2013-03-06
- Volume
- 6
- Issue
- 3
- Pages
- 856-869
- ISSN
- 1996-1944 (ISSN-L)
- OpenAlex
- W2140404087
- Cited by
- 307
- References
- 21
- FWCI
- 31.88
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: From Powders to Dense Metal Parts: Characterization of a Commercial AlSiMg Alloy Processed through Direct Metal Laser Sintering. https://app.cochat.ai/papers/10.3390/ma6030856
- The paper
- Manfredi, D., Calignano, F., Krishnan, M., Canali, R., Ambrosio, E., & Atzeni, E. (2013). From Powders to Dense Metal Parts: Characterization of a Commercial AlSiMg Alloy Processed through Direct Metal Laser Sintering. Materials. https://doi.org/10.3390/ma6030856
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.