The DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index; 18 of the 47 sources its claims cite were checked for support.
Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR
Open accessAbstract
The degradation of mulch materials in perennial cropping systems is governed by both polymer properties and environmental conditions. Their relative influence under field conditions remains unclear. To our knowledge, this study is one of the first to integrate mass loss measurements, polymer characterization, and soil microclimatic assessment under field conditions. A one-year field experiment was conducted under irrigated Mediterranean conditions to compare the degradation of Kraft® paper and polybutylene adipate terephthalate (PBAT)-based (Kritifil®) mulch with polypropylene (PP) geotextile fabric and polyethylene (PE) mulch in randomized blocks, with three replicates. Mass loss was quantified in situ using mesh bags, while soil moisture, temperature, and electrical conductivity (EC) were monitored monthly to characterize microclimatic and edaphic conditions underlying mulch treatments. Polymer changes were assessed by ATR-FTIR analysis of field-exposed mulch fragments. Kraft® paper degraded rapidly (≈72% mass loss), consistent with moisture-driven biological processes and susceptibility to hydrolysis. In contrast, PBAT-based mulch showed limited degradation (≈3.5%) despite favourable conditions, suggesting constraints in enzymatic activity. No mass loss was observed for PE- and PP-based mulch. ATR-FTIR analysis indicated minimal structural changes in PBAT, PP, and PE, reflecting their high stability. Overall, polymer composition and inherent (bio)degradability, rather than soil thermal time, were the main drivers of mulch (bio)degradation under Mediterranean conditions.
Overview
CoChat Summary
TL;DR
In a one-year Mediterranean field trial, Kraft® paper mulch degraded rapidly (72 ± 18.5% mass loss), while PBAT-based mulch showed only 3.5 ± 5.7% mass loss and PP/PE showed no true mass loss. Polymer composition and inherent (bio)degradability, rather than soil thermal time, were the main drivers of mulch degradation.
Key findings
- Kraft® paper had the highest mass loss at 72 ± 18.5% after one year; PBAT-based Kritifil® showed minimal mass loss at 3.5 ± 5.7%; PP and PE showed no true mass loss, with net mass changes of −1.7 ± 17.4% and −11.3 ± 6.6%, respectively, attributed to microbial colonization and/or soil particle adhesion.
- Soil moisture averaged 22.6%; mean annual soil temperature was highest under black PBAT biofilm (21.7 °C) and lowest under Kraft® paper (21.4 °C). Estimated cumulative thermal time followed PBAT 9245.43 > PE 9208.50 > PP 9131.83 > Kraft® paper 9106.83 °day.
- ATR-FTIR indicated limited structural change in PBAT, PP, and PE. Kraft® paper showed increased O–H intensity near 3400 cm−1; PBAT showed slight decreases in ester carbonyl/C–O bands with increased O–H, consistent with limited superficial hydrolysis; PP and PE retained main fingerprint bands but showed surface oxidation features (O–H 3200–3600 cm−1, carbonyl 1710–1740 cm−1).
- The authors concluded that polymer composition and accessibility to enzymatic activity largely determined degradation rates, whereas cumulative soil temperature and other microclimatic factors played only a minor role.
Methods
- Field experiment at the Innovation Pole of Fataca, Odemira, southern Portugal (37.5903° N, 8.7403° W), under irrigated Mediterranean conditions with blueberry cv. Centra Blue. Four mulch treatments—Kraft® paper biofilm, PP-based geotextile fabric, black PE film (40 µm), and black Kritifil® PBAT-based biofilm (14 µm)—were arranged in a randomized complete block design with three replicates, each with five plants.
- Mass loss was measured using nylon mesh bags (20 × 20 cm, ~1 mm openings) containing 30 pieces of mulch (1.5 × 1.5 cm each), placed beneath the corresponding mulch in October 2024 and recovered after 361 days. Soil moisture, temperature, and EC were monitored monthly at 0–20 cm from 1 September 2024 to 14 October 2025; cumulative thermal time was calculated with Tbase = 0 °C.
- Recovered fragments were analyzed by ATR-FTIR (600–4000 cm−1, 64 scans, 4 cm−1 resolution) and compared with pristine polymers. Data were presented as means ± SD (n = 3); normality and homogeneity were tested with Shapiro–Wilk and Levene’s tests, followed by one-way ANOVA and Bonferroni post hoc comparisons (p < 0.05).
Limitations
- Stated: findings are specific to irrigated Mediterranean conditions and should be extrapolated cautiously; future work should include more frequent sampling, larger numbers of replicates, longer-term monitoring, and a wider range of environmental conditions.
- Stated: enzymes directly involved in PBAT biodegradation—esterase, cutinase, and lipase—were not measured, so the soil’s effective enzymatic capacity to degrade PBAT could not be directly inferred. Point-in-time temperature measurements may underestimate daily maxima, and only cumulative thermal time was estimated due to monthly sampling.
- Stated/evident: mass loss may be overestimated if film pieces escaped through mesh bag holes, though care was taken during washing with a 0.5 mm sieve. ATR-FTIR changes on PP and PE may also arise from biofilms, so they cannot be unequivocally attributed to polymer oxidation alone.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures






Verification
Claims the paper makes
14 Valid · 0 Not valid · 16 Not checked · 76 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The (bio)degradation rates of mulch films, whether conventional plastic or biodegradable, depend not only on their chemical composition but also on a range of external factors [6,9].”
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 1. Introduction
What the sources say
- Partly supportedcites [6] Bianchini, 2022, Soil refinement accelerates in-field degradation rates of soil-biodegradable mulch films, Ital. J. Agron. sourceExperimental — accuracy not yet measured
The Introduction states that mulch-film biodegradation rates depend on chemical composition and abiotic and biotic factors. The paper discusses this in the context of soil-biodegradable films; it does not establish the same claim for conventional plastic films, so that extension is unsupported. (LLM, conf=0.85)
- Not checked — no full text of the sourcecites [9] Graf, 2025, Biodegradable mulch films exhibit slower-than-expected degradation with negligible effects on soil microbial communities, J. Hazard. Mater. source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The slightly lower soil temperatures observed under Kraft® paper in the present study are likely attributable to its lighter colour and higher reflectance, which reduced heat absorption and led to the lowest annual thermal accumulation [5,16]”
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.1. Monitoring of Soil Properties
What the sources say
- Partly supportedcites [5] Tofanelli, M.D., and Wortman, S.E. (2020). Benchmarking the agronomic performance of biodegradable mulches against polyethylene mulch film: A meta-analysis. Agronomy, 10. sourceExperimental — accuracy not yet measured
Section 3.2 (Soil Temperature) reports that paper mulches reduced soil temperature relative to polyethylene and explains that light-colored mulches reflect more solar radiation. It does not establish that Kraft® paper’s lighter color or reflectance caused the citing study’s result; for brown, typically paper-based mulches, it says lower temperatures were more likely driven by paper’s poor thermal absorptivity and transmittance. (LLM, conf=0.83)
- Supportedcites [16] Kadera, 2017, Mulching type-induced soil moisture and temperature regimes and water use efficiency of soybean under rain-fed condition in central Japan, Int. Soil Water Conserv. Res. source
Section 3.2 reports the lowest soil temperatures under paper mulch and gives lighter colour and reflected light, rather than absorption by darker surfaces, as an explanation. The Kraft® paper temperatures are identified in the citing sentence as observations from the citing authors’ own study; this source supports the proposed mechanism. (LLM, conf=0.88)
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“These assignments confirm the typical PBAT polymer backbone structure [8,21,22].”
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.3. Evidence of Deterioration Based on ATR-FTIR Spectral Changes
What the sources say
- Not checked — no full text of the sourcecites [8] Coutris, 2025, In situ degradation of biodegradable plastic mulch in Nordic agricultural soils, Chemosphere source
- Not checked — no full text of the sourcecites [21] Oliveira, 2017, Effect of reprocessing cycles on the degradation of PP/PBAT-thermoplastic starch blends, Carbohydr. Polym. source
- Supportedcites [22] Tsou, 2022, The preparation and performance of poly(butylene adipate) terephthalate/corn stalk composites, Curr. Res. Green. Sustain. Chem. source
Section 3.4 (Fourier transform infrared analysis; page not supplied) assigns FTIR bands in PBAT to methylene, carbonyl, C–O–C, benzene-ring, and phenylene groups. Those assignments support the citing sentence’s description of a typical PBAT backbone structure. (LLM, conf=0.91)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“These features are consistent with early-stage abiotic weathering (surface oxidation), rather than true biodegradation [24,25,26].”
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.3. Evidence of Deterioration Based on ATR-FTIR Spectral Changes
What the sources say
- Not checked — no full text of the sourcecites [24] Achimsky, 1997, Kinetic study of the thermal oxidation of polypropylene, Polym. Degrad. Stab. source
- Not checked — no full text of the sourcecites [25] Padermshoke, 2022, Characterization of photo-oxidative degradation process of polyolefins containing oxo-biodegradable additives, Polymer source
- Partly supportedcites [26] Anshari, 2025, Raman and ATR-FTIR unmask crystallinity changes and carboxylate group and vinyl group accumulation in natural weathering polypropylene microplastic, Sci. Rep. sourceExperimental — accuracy not yet measured
The Discussion (page unavailable) describes photooxidation as a major abiotic pathway for PP weathering and says abiotic degradation is generally the initial step before biotic degradation. The Results report stronger weathering effects on outside surfaces. But the paper does not establish that the observed features are early-stage or rule out biodegradation; its Conclusion instead calls the degradation of its samples considerably high. (LLM, conf=0.86)
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Taken together, the mass-change results and ATR-FTIR analyses highlighted contrasting behaviours among cellulose, PBAT-, PP-, and PE-based materials under the tested field conditions [26,29,30,31].”
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.3. Evidence of Deterioration Based on ATR-FTIR Spectral Changes
What the sources say
- Partly supportedcites [26] Anshari, 2025, Raman and ATR-FTIR unmask crystallinity changes and carboxylate group and vinyl group accumulation in natural weathering polypropylene microplastic, Sci. Rep. sourceExperimental — accuracy not yet measured
The Results section ('ATR-FTIR spectra of NWPP samples'; page not provided) reports spectral changes in naturally weathered polypropylene, supporting the PP-related ATR-FTIR portion. The paper does not report mass-change results or compare cellulose, PBAT, PP, and PE under the citing study’s tested field conditions. (LLM, conf=0.87)
- Partly supportedcites [29] Di Pippo, F., Bocci, V., Amalfitano, S., Crognale, S., Levantesi, C., Pietrelli, L., Di Lisio, V., Martinelli, A., and Rossetti, S. (2023). Microbial colonization patterns and biodegradation of petrochemical and biodegradable plastics in lake waters: Insights from a field experiment. Front. Microbiol., 14. sourceExperimental — accuracy not yet measured
The Results (Polymer surface analysis; page unavailable) report contrasting ATR-FTIR findings for the PBAT-containing MaterBi material and low-density polyethylene after lake-water immersion. The Experimental design and field work section lists the tested materials as LDPE, PET, PLA, and MaterBi; it does not include cellulose or polypropylene. The retrieved passages also do not report mass-change results, so this source supports only part of the cited sentence. (LLM, conf=0.87)
- Not checked — no full text of the sourcecites [30] Koseki, 2025, Polypropylene reinforced with hollow glass microspheres: Effect of thermal aging and reprocessing, Polímeros Ciência Tecnol. source
- Partly supportedcites [31] Sonohata, H., Manago, G., Seike, S., Kitawaki, H., and Tanabe, T. (2025). Evaluation of plastic waste degradation using terahertz spectroscopy for material recycling. Recycling, 10. sourceExperimental — accuracy not yet measured
Sections 3.1 and 5.1 report FTIR analysis of PE and PP, supporting that part of the cited sentence. But Sections 3.2–3.3 describe artificial thermal and UV degradation, not field conditions, and Section 4.1 specifies transmission FTIR rather than ATR-FTIR. The paper does not report mass-change results or examine cellulose or PBAT. (LLM, conf=0.88)
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
39 more claims · 2 with their cited sources checked
Create a free account to see all 106 claims and to verify the 1 reference still open.
- Probably not a substantial claim. 23
- It may state two separate claims as one. 49
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.3. Evidence of Deterioration Based on ATR-FTIR Spectral Changes
“Together, the spectral modifications indicate limited depolymerisation through hydrolytic processes under soil moisture conditions, without evidence of extensive bulk polymer degradation [8].”
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.3. Evidence of Deterioration Based on ATR-FTIR Spectral Changes
“in PBAT, the O–H band primarily indicated limited water absorption, with no clear evidence of chemical or enzymatic degradation”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.3. Evidence of Deterioration Based on ATR-FTIR Spectral Changes
“the relatively low concentration of low additive (2.64 ± 0.52 kg kg−1) [19]”
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.2. In Situ Degradation of Conventional Plastic and Biodegradable Mulch Materials: Mass Loss
“the relatively low di(2-ethylhexyl) phthalate (DEHP) concentration in the PBAT (2.64 ± 0.52 mg kg−1; Table 2)”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.1. Monitoring of Soil Properties
“The mean annual soil temperature was the highest under the black PBAT biofilm (21.7 °C), whereas the lowest temperature was recorded beneath Kraft® paper (21.4 °C)”
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.1. Monitoring of Soil Properties
“Black mulches (PBAT and PE) promoted greater soil warming, resulting in higher mean annual temperature (21.6–21.7 °C, respectively)”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 2. Results and Discussion > 2.3. Evidence of Deterioration Based on ATR-FTIR Spectral Changes
“the relatively high DEHP concentration measured in the geotextile fabric (32.3 ± 7.6 mg kg−1; Table 1)”
§ Linking Polymer Transformation and Soil Microclimate to Mulch (Bio)Degradation: A Field-Based Approach Using Mesh Bags and FTIR > 3. Materials and Methods > 3.1. Study Design
“In the present study, the DEHP concentration in mulch materials (Table 2) was extracted from the mulches by liquid extraction with organic solvents (n-hexane and dichloromethane) and determined by gas chromatography analysis.”
Citations
Cites
Jung, M. R., Horgen, F. D., Orski, S. V., Rodriguez C., V., Beers, K. L., Balazs, G. H., Jones, T. T., Work, T. M., Brignac, K. C., Royer, S.-J., et al. (2018) · Marine Pollution Bulletin · doi:10.1016/j.marpolbul.2017.12.061 · Cited by 1,466 · cited 1×
“Jung et al. [23] also observed similar spectra for PP-based materials.”
In Situ degradation of biodegradable plastic mulch films in compost and agricultural soils
Sintim, H. Y., Bary, A. I., Hayes, D. G., Wadsworth, L. C., Anunciado, M. B., English, M. E., Bandopadhyay, S., Schaeffer, S. M., DeBruyn, J. M., Miles, C. A., et al. (2020) · Science of The Total Environment · doi:10.1016/j.scitotenv.2020.138668 · Cited by 377 · cited 8×
“In previous studies, Sintim et al. [1] used mesh bags with 250 µ m openings to minimize material loss while still allowing for microbial degradation, while Graf et al. [9] tested nylon mesh bags with 100 µ m and 5 mm openings to evaluate microbial decomposition, and meso-to macrofauna-mediated…”
InfluentialImpacts of biodegradable plastic mulches on soil health
Sintim, H. Y., Bandopadhyay, S., English, M. E., Bary, A. I., DeBruyn, J. M., Schaeffer, S. M., Miles, C. A., Reganold, J. P., & Flury, M. (2019) · Agriculture, Ecosystems & Environment · doi:10.1016/j.agee.2018.12.002 · Cited by 249 · cited 2×
“The mean annual soil temperature was the highest under the black PBAT biofilm (21.7 ◦ C), whereas the lowest temperature was recorded beneath Kraft ® paper (21.4 ◦ C) (Figure 1(B-1)), in agreement with [3,12].”
InfluentialAssessment of agricultural plastics and their sustainability: A call for action
(2021) · FAO eBooks · doi:10.4060/cb7856en · Cited by 193
Li, X., Wang, Q., Jiang, N., Lv, H., Liang, C., Yang, H., Yao, X., & Wang, J. (2023) · Environmental Research · doi:10.1016/j.envres.2022.115196 · Cited by 183 · cited 1×
“Due to phthalate ability to migrate into soil and crops, they may contribute to environmental contamination and potential human exposure associated with endocrine and reproductive health effects [36].”
Salomez, M., George, M., Fabre, P., Touchaleaume, F., Cesar, G., Lajarrige, A., & Gastaldi, E. (2019) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2019.06.025 · Cited by 140 · cited 2×
“%) of initial weight and calculated according to (1) [1,6]: {[initial weight (mg/bag) − final weight (mg/bag)]/initial weight (mg/bag)} × 100 (1) Salomez et al. [32] considered the mass loss method the most relevant and accurate to assess the degradation of mulch material.”
In-field degradation of soil-biodegradable plastic mulch films in a Mediterranean climate
Griffin-LaHue, D., Ghimire, S., Yu, Y., Scheenstra, E. J., Miles, C. A., & Flury, M. (2022) · Science of The Total Environment · doi:10.1016/j.scitotenv.2021.150238 · Cited by 135
CHANGES IN LEAF LITTER WHEN PLACED ON THE SURFACE OF SOILS WITH CONTRASTING HUMUS TYPES
Bocock, K. L., GILBERT, O., CAPSTICK, C. K., et al. (1960) · Journal of Soil Science · doi:10.1111/j.1365-2389.1960.tb02196.x · Cited by 134 · cited 1×
“The nylon mesh bag technique [1,15,39] was applied on the surface of raised beds at the Fataca farm.”
Kader, M. A., Senge, M., Mojid, M. A., & Nakamura, K. (2017) · International Soil and Water Conservation Research · doi:10.1016/j.iswcr.2017.08.001 · Cited by 116 · cited 1×
“The slightly lower soil temperatures observed under Kraft ® paper in the present study are likely attributable to its lighter colour and higher reflectance, which reduced heat absorption and led to the lowest annual thermal accumulation [5,16], and may help to prevent root-zone stress in summer.”
Tofanelli, M. B. D., & Wortman, S. E. (2020) · Agronomy · doi:10.3390/agronomy10101618 · Cited by 101 · cited 4×
“The slightly lower soil temperatures observed under Kraft ® paper in the present study are likely attributable to its lighter colour and higher reflectance, which reduced heat absorption and led to the lowest annual thermal accumulation [5,16], and may help to prevent root-zone stress in summer.”
InfluentialEffect of reprocessing cycles on the degradation of PP/PBAT-thermoplastic starch blends
Oliveira, T. A., Oliveira, R. R., Barbosa, R., Azevedo, J. B., & Alves, T. S. (2017) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2017.03.054 · Cited by 92 · cited 1×
“These assignments confirm the typical PBAT polymer backbone structure [8,21,22].”
Wang, Z., Li, M., Flury, M., Schaeffer, S. M., Chang, Y., Tao, Z., Jia, Z., Li, S., Ding, F., & Wang, J. (2021) · The Science of The Total Environment · doi:10.1016/j.scitotenv.2021.147460 · Cited by 88 · cited 3×
“Based on monthly temperature measurements, the estimated cumulative thermal time ( ◦ day, T base = 0 ◦ C) [8,14,15] day, respectively).”
Anshari, R., Tsuboi, M., Sato, H., Tashiro, K., & Ozaki, Y. (2025) · Scientific Reports · doi:10.1038/s41598-025-85837-y · Cited by 78 · cited 2×
“Taken together, the mass-change re-sults and ATR-FTIR analyses highlighted contrasting behaviours among cellulose, PBAT-, PP-, and PE-based materials under the tested field conditions [26,29–31].”
Plastic mulch use in perennial fruit cropping systems – A review
Zhang, H., Miles, C. A., Gerdeman, B. S., Griffin-LaHue, D., & DeVetter, L. W. (2021) · Scientia Horticulturae · doi:10.1016/j.scienta.2021.109975 · Cited by 77 · cited 4×
“The mean annual soil temperature was the highest under the black PBAT biofilm (21.7 ◦ C), whereas the lowest temperature was recorded beneath Kraft ® paper (21.4 ◦ C) (Figure 1(B-1)), in agreement with [3,12].”
Influentialda Silva, D. J., & Wiebeck, H. (2022) · Journal of Polymers and the Environment · doi:10.1007/s10924-022-02396-3 · Cited by 58
The preparation and performance of poly(butylene adipate) terephthalate/corn stalk composites
Tsou, C.-H., Chen, Z.-J., Yuan, S., Ma, Z.-L., Wu, C.-S., Yang, T., Jia, C.-F., & Reyes De Guzman, M. (2022) · Current Research in Green and Sustainable Chemistry · doi:10.1016/j.crgsc.2022.100329 · Cited by 55 · cited 1×
“These assignments confirm the typical PBAT polymer backbone structure [8,21,22].”
Kinetic study of the thermal oxidation of polypropylene
Achimsky, L., Audouin, L., & Verdu, J. (1997) · Polymer Degradation and Stability · doi:10.1016/s0141-3910(96)00167-x · Cited by 47 · cited 1×
“These features are consistent with early-stage abiotic weathering (surface oxidation), rather than true biodegradation [24–26].”
Padermshoke, A., Kajiwara, T., An, Y., Takigawa, M., Van Nguyen, T., Masunaga, H., Kobayashi, Y., Ito, H., Sasaki, S., & Takahara, A. (2022) · Polymer · doi:10.1016/j.polymer.2022.125455 · Cited by 40
Evaluation of the mulch films biodegradation in soil: A methodological review
Francioni, M., Kishimoto-Mo, A. W., Tsuboi, S., & Hoshino, Y. T. (2022) · Italian Journal of Agronomy · doi:10.4081/ija.2021.1936 · Cited by 37 · cited 7×
“The initial phase, biodeterioration , involves physical/abiotic weathering and enzymatic activity, during which microbial colonization and biofilm formation induce early surface alterations, particularly under warm and moist conditions [2,6,8,10].”
InfluentialDi Pippo, F., Bocci, V., Amalfitano, S., Crognale, S., Levantesi, C., Pietrelli, L., Di Lisio, V., Martinelli, A., & Rossetti, S. (2023) · Frontiers in Microbiology · doi:10.3389/fmicb.2023.1290441 · Cited by 28 · cited 1×
“Taken together, the mass-change re-sults and ATR-FTIR analyses highlighted contrasting behaviours among cellulose, PBAT-, PP-, and PE-based materials under the tested field conditions [26,29–31].”
Analytical tools to assess polymer biodegradation: A critical review and recommendations
Colachis, M., Lilly, J. L., Trigg, E., & Kucharzyk, K. H. (2024) · Science of The Total Environment · doi:10.1016/j.scitotenv.2024.176920 · Cited by 21 · cited 1×
“Spectroscopic techniques, in turn, offer valuable complementary information by enabling the detection of chemical and structural changes in the polymers [10,11], thereby improving the assessment of the degradation status of the original materials.”
An integral model to calculate the growing degree-days and heat units, a spreadsheet application
Elnesr, M. N., & Alazba, A. A. (2016) · Computers and Electronics in Agriculture · doi:10.1016/j.compag.2016.03.024 · Cited by 20 · cited 1×
“Growing degree-days ( ◦ day), also referred to as thermal time or heat units, were calculated by summing, over time, the difference between observed temperatures and the base temperature [14,15,38].”
Soil refinement accelerates in-field degradation rates of soil-biodegradable mulch films
Bianchini, M., Trozzo, L., D’Ottavio, P., Giustozzi, M., Toderi, M., Ledda, L., & Francioni, M. (2022) · Italian Journal of Agronomy · doi:10.4081/ija.2022.2044 · Cited by 20 · cited 9×
“The initial phase, biodeterioration , involves physical/abiotic weathering and enzymatic activity, during which microbial colonization and biofilm formation induce early surface alterations, particularly under warm and moist conditions [2,6,8,10].”
InfluentialSenescent leaf decomposition in a Mediterranean pear orchard
Neto, C., Carranca, C., & Clemente, J. (2009) · European Journal of Agronomy · doi:10.1016/j.eja.2008.07.004 · Cited by 18 · cited 2×
“…avoid both underestimation (by leaving too many soil particles adsorbed) or overestimation of mass loss (by destroying or losing the material) [2,9,10,40], and washed pieces were counted, air-dried to constant weight, and weighed with an precision balance, as also reported by Bianchini et al. [6].”
InfluentialSelf-citationPedra, F., Inácio, M. L., Fareleira, P., Oliveira, P. B., Pereira, P., & Carranca, C. (2024) · Pollutants · doi:10.3390/pollutants4010002 · Cited by 15 · cited 1×
“= V. virgatum Aiton) by the Horticulture and Food Research Institute of New Zealand Limited (HortResearch) [33], were manually transplanted from a nursery to the field (Figure 4).”
Self-citationEvaluating additive release from conventional and biodegradable mulch films
Scopetani, C., Bellabarba, A., Selvolini, G., Martellini, T., Viti, C., & Cincinelli, A. (2025) · Science of The Total Environment · doi:10.1016/j.scitotenv.2025.179294 · Cited by 15 · cited 4×
“…reduced accessibility of the polymer matrix to water and microorganisms, and the requirement for specific soil microbial enzyme esterases for efficient depolymerisation, rather than to polymer thickness (14 µ m) or the relatively low concentration of low additive (2.64 ± 0.52 kg kg − 1 ) [19].”
InfluentialGraf, M., Choiselat, E., Reay, M. K., Bargiela, R., Dimitriou, A., Liu, Q., Elias, R. M., Golyshin, P. N., Griffiths, R., Chadwick, D. R., et al. (2025) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2025.139871 · Cited by 15
In situ degradation of biodegradable plastic mulch in Nordic agricultural soils
Coutris, C., Rivier, P.-A., Torp, T., Klaus, J., & Joner, E. J. (2025) · Chemosphere · doi:10.1016/j.chemosphere.2025.144516 · Cited by 12 · cited 7×
“In addition, Coutris et al. [8] reported mass losses for PBAT-based mulch materials in mesh bags varying from 8% to 48% after 12 months, respectively, in a cold Norwegian climate, with little difference in mass loss at both the 10 and 30 cm soil depths.”
InfluentialSenevirathne, G. I., Gimhani, T. D. M., Reay, M. K., Perera, C., Ariyaratna, M., Karunarathna, A. K., Chadwick, D. R., Jones, D. L., Emrah, C., Lloyd, C. E. M., et al. (2025) · Environmental Advances · doi:10.1016/j.envadv.2025.100628 · Cited by 8 · cited 6×
“The initial phase, biodeterioration , involves physical/abiotic weathering and enzymatic activity, during which microbial colonization and biofilm formation induce early surface alterations, particularly under warm and moist conditions [2,6,8,10].”
InfluentialAppiah, K. S., Onwona‐Agyeman, S., Omari, R. A., Horiuchi, N., Sarkodee-Addo, E., Sabi, E. B., & Fujii, Y. (2023) · Agronomy · doi:10.3390/agronomy13020351 · Cited by 7 · cited 1×
“Field-based studies evaluating the degradation and biodegradation rates of mulch materials have gained increasing importance in recent years, following the FAO’s [17] call for the urgent replacement of conventional plastics with biodegradable alternatives [6,7,18].”
Bacterial isolation and evaluation for degradation of unpretreated LDPE from waste dump soils
Thakur, S., Mathur, S., Saraf, M., Patel, S., Jadav, R., & Menon, S. (2025) · Journal of Pure and Applied Microbiology · doi:10.22207/jpam.19.2.45 · Cited by 5 · cited 2×
“Nevertheless, these changes may also be associated with microbial colonization at the polymer surface, making it difficult to distinguish between true polymer oxidation and biofilm-related signals on PP and PE surfaces [27].”
Evaluation of Plastic Waste Degradation Using Terahertz Spectroscopy for Material Recycling
Sonohata, H., Manago, G., Seike, S., Kitawaki, H., & Tanabe, T. (2025) · Recycling · doi:10.3390/recycling10040134 · Cited by 3
Polypropylene reinforced with hollow glass microspheres: Effect of thermal aging and reprocessing
Koseki, H. C. M., Bergozza, M., Braz, C. J. D. F., Alves, T. S., & Barbosa, R. (2025) · Polímeros · doi:10.1590/0104-1428.20240047 · Cited by 1
Machado, R. M. A., Bryla, D. R., & Correia, M. (2023) · Acta Horticulturae · doi:10.17660/actahortic.2023.1357.55
Research works printed but not linked: 2
- Campbell, G.S., and Norman, J.M. (1979). An Introduction to Environmental Biophysics, Springer.
- Kamel, 2018, Preparation and infrared study of cellulose based amphiphilic materials, Cellul. Chem. Technol., 52, 193
Cited by
Pereira, P., Ramos, A. C., Machado, R. M. A., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.7244096
Self-citation
Metadata
- Authors
- Carranca, C., Pedra, F., Brunetto, G., & Barata, J.
- Affiliations
- Instituto Nacional de Investigação Agrária e Veterinária (PT)
- Universidade Federal de Santa Maria (BR)
- Centro de Estudos do Ambiente e do Mar (PT)
- Corresponding author
- Carranca, Corina
- Venue
- Molecules
- Publisher
- MDPI AG
- Published
- 2026-05-20
- Volume
- 31
- Issue
- 10
- Pages
- 1758
- ISSN
- 1420-3049 (ISSN-L)
- PMC
- PMC13209953
- OpenAlex
- W7161799024
- Cited by
- 2
- References
- 32
- Citations by year
- 2026: 2
- FWCI
- 3.39
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Molecules (publishedVersion, cc-by)
- PubMed (publishedVersion)
- PubMed Central (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Green-it—Bioresources for Sustainability (UID/04551/2025, UID/PRR/04551/2025)
- LS4FUTURE Associated Laboratory (LA/P/0087/2020)
- CESAM—Centro de Estudos do Ambiente e do Mar (UID/50017/2025, LA/P/0094/2020)
- Topics
- Life Sciences › Agricultural and Biological Sciences › Agronomy and Crop Science › Polymer-Based Agricultural Enhancements
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Environmental Science › Pollution › Microplastics and Plastic Pollution
- Keywords
- biodegradable mulch, soil microclimate, polymer transformation, kraft paper, poly(butylene adipate-co-terephthalate), polypropylene geotextile, polyethylene mulch, mass loss, soil moisture, hydrolysis, enzymatic degradation, Mediterranean climate, perennial cropping systems
- MeSH terms
- Biodegradation, Environmental, Microclimate, Paper, Polyesters, Polymers, Polypropylenes, Soil, Temperature, Spectroscopy, Fourier Transform Infrared, Polyethylene
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-30, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-09-30 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.