The DOI matches its Crossref record; 46 of the 46 references it cites were found in a registry or an index; none of the 28 sources its claims cite is checked for support yet.
Assessment of SWOT water surface elevations for flood monitoring of a narrow river ( < 50 m width)
Open accessPublished version of a preprint
Abstract
Floods are among the most frequent and damaging natural hazards worldwide, and reliable observations of water surface elevation (WSE) are essential for improving flood modelling and risk management. The Surface Water and Ocean Topography (SWOT) satellite, launched in 2022, offers new opportunities to monitor river hydrodynamics from space, but its performance in relatively narrow rivers (< 50 m width) remains poorly documented. This study evaluates the potential of SWOT WSEs for flood monitoring through a site-specific hydraulic application by comparing them with in situ observations as well as simulations from an existing large-scale hydraulic model (LISFLOOD-FP) on the Du Gouffre River (width ≈ 40 m), located in Quebec, Canada. The L2_HR_RiverSP (RiverSP) SWOT product Version D, derived from a priori database (SWORD-version 17b), was first compared with one-minute WSE measurements from a tidal gauge located downstream the Du Gouffre River in the St. Lawrence River. This comparison, based on in situ reference measurements, confirmed the overall quality of the SWOT data in this area, with a Root Mean Square Error (RMSE) of 0.25 m. Then, a major flood event (with a return period of about 60 years) which occurred on 1 May 2023, during the SWOT's calibration orbit, was used to conduct a daily analysis of the entire flood event. Eleven observation cycles, covering the period from 25 April to 7 May 2023, were analysed. Limited ground-based observations were available along the studied reach during the flood, highlighting the added value of SWOT observations in this data-scarce context. The 1D/2D hydraulic model LISFLOOD-FP was run for the discharges corresponding to eleven SWOT cycles. Comparisons between SWOT-derived WSEs and model-simulated WSEs yielded biases ranging from −0.30 to 0.43 m and RMSE values between 0.22 and 0.54 m, indicating generall consistent behavior between observed and simulated WSEs across the analyzed cycles. During the flood peak on 1 May, larger discrepancies were observed, reflecting uncertainties in upstream discharge estimates under extreme flow conditions. In this context, SWOT-derived WSEs provided complementary information that helped diagnose discharge underestimation during the peak event. These results are not intended as an independent validation of SWOT measurement accuracy but are specific to the river and flood event under study and demonstrate the practical usefulness of SWOT observations for hydraulic studies in narrow rivers. They highlight the potential contribution of SWOT data for flood monitoring and hydraulic modelling in similar data-scarce contexts, particularly under extreme hydrological conditions.
Overview
CoChat Summary
TL;DR
This site-specific case study compares SWOT Level-2 RiverSP (Version D, `wse_sm`) water surface elevations with in situ gauge data and LISFLOOD-FP simulations for the ~40 m wide Du Gouffre River (Quebec, Canada) during a ~60-year flood on 1 May 2023. SWOT WSEs agreed with the downstream tide gauge (RMSE 0.25 m) and with model simulations across eleven cycles (bias −0.30 to 0.43 m; RMSE 0.22–0.54 m), and helped diagnose an underestimated tributary inflow at the flood peak.
Key findings
- Against one-minute tide-gauge observations at Saint-Joseph-de-la-Rive (April 2023–August 2025, ice-free), the 68th-percentile absolute error was 0.24 m with an RMSE of 0.25 m and a median absolute error of 0.16 m, meeting the SWOT 1-sigma requirement of 0.25 m for water bodies of 250 m²–1 km².
- Across eleven SWOT cycles (25 April–7 May 2023), SWOT-vs-LISFLOOD-FP biases ranged from −0.30 to 0.43 m and RMSE from 0.22 to 0.54 m; pre-peak cycles (502, 503, 506, 507) had biases of 0.28–0.43 m and RMSE 0.47–0.53 m, while recession cycles (511–514) had biases ≤0.33 m and RMSE 0.29–0.40 m.
- At the 1 May flood peak (cycle 508), the unadjusted simulation showed a bias of 1.30 m and RMSE of −1.21 m; raising the Des Mares tributary inflow to 240 m³ s⁻¹ improved agreement to a bias of −0.30 m and RMSE of 0.54 m, indicating the model had underestimated tributary discharge.
- Cycle 509 (recession) showed a bias of −0.10 m and RMSE of 0.22 m; cycle 510 was discarded because all nodes had `xovr_cal_q` = 2. The maximum RMSE of 0.54 m represents ~27% of the ~2 m flood-stage amplitude, and the maximum bias of 0.42 m ~22%.
Methods
- Case study on the Du Gouffre River (watershed ~991 km², active channel width ~40 m, floodplain 300–400 m), which experienced a flood with a 60-year return period for maximum 3-hour discharge (150 years for daily average); flow rose from 75 to 500 m³ s⁻¹ within 12 h, following ~170 mm of snowmelt water and 95–142 mm of rain (30 April–2 May).
- SWOT L2_HR_RiverSP Version D node-level `wse_sm` values were filtered using `node_q` (≤2) and `xovr_cal_q` (0 or 1), converted from ITRF2014/WGS84/EGM2008 to NAD83 (CSRS) epoch 1997.0 / CGVD28 via NRCan TRX and GPS-H, and compared node-by-node with an existing LISFLOOD-FP 1D/2D model (Manning's n = 0.03 channel; floodplain n from land use).
- Discharges were derived from a post-flood rating curve at station 051305 (Saint-Urbain, 11.6 km upstream) using BaRatinAGE and transposed by drainage-area ratio (632 km² at Saint-Urbain vs 889 km² at Baie-Saint-Paul); downstream boundary from tide station 03057. Statistics computed per overpass were RMSE and bias; sensitivity tests varied Manning's n (0.027–0.029) and the downstream boundary.
Limitations
- The authors state that, apart from one downstream tidal gauge and one upstream hydrometric station, no spatially distributed in situ WSE measurements were available during the flood, and they frame the work as a site-specific case study rather than a rigorous assessment of SWOT measurement accuracy.
- Because SWOT WSEs were used to adjust the Des Mares tributary inflow for cycle 508, the authors explicitly state that the improved agreement for that cycle is not an independent validation of SWOT accuracy.
- The paper notes that SWOT Science Requirements are defined for reach-scale products whereas this assessment uses node-level WSEs, so comparison with mission requirements is "not appropriate"; it also reports that a manual outlier filter (removing nodes with >1 m SWOT–model difference) strongly changed error metrics for some cycles (e.g., cycle 509 RMSE from 6.51 to 0.22 m), and calls for future work linking quality flags to automatic outlier detection.
- Evident in the text: the reported 68th-percentile absolute error against the tide gauge differs between sections (0.24 m in Results vs 0.05 m in Discussion and Conclusion), and the pre-adjustment cycle 508 RMSE is reported as a negative value (−1.21 m), both of which appear to be internal inconsistencies.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 1 Not valid · 23 Not checked · 70 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Moreover, parameter adjustments that slightly improved agreement during the flood peak systematically led to a deterioration of model-SWOT consistency for the other cycles.”
§ 2 Methods > 2.3 Hydraulic Modelling: LISFLOOD-FP
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“indicating that the 68th percentile (corresponding to the 1-sigma metric defined in the SWOT requirements) is 0.24 m, with an RMSE of 0.25 m.”
- Also stated in: § Abstract · plain
“with a Root Mean Square Error (RMSE) of 0.25 m.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § Abstract · plain
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“For cycle 508, a comparison between SWOT-derived WSEs and LISFLOOD-FP simulations prior to any adjustment of the Des Mares tributary inflow shows a bias of 1.30 m and an RMSE of −1.21 m.”
plainstates an associationSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“with a median of 0.16 m”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The transposed discharge at the Saint-Urbain station (357 m3 s−1) was lower than the maximum value of 505 m3 s−1 recorded only a few hours before the SWOT overpass (Fig. 2).”
§ 2 Methods > 2.3 Hydraulic Modelling: LISFLOOD-FP
plainSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
43 more claims
Create a free account to see all 94 claims and to verify the 14 references still open.
- It may state two separate claims as one. 33
- The quote only partly states this claim. 1
- Probably not a substantial claim. 19
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ 3 Results
“Figure 3a shows the probability that the absolute WSE error is less than or equal to a given value (Likelihood of occurrence), indicating that the 68th percentile (corresponding to the 1-sigma metric defined in the SWOT requirements) is 0.24 m, with an RMSE of 0.25 m.”
§ 4 Discussion and Conclusion
“First, the comparison between SWOT-derived WSEs and one-minute observations at the downstream tidal gauge shows good agreement, with a 68th percentile absolute error of 0.05 m and an RMSE of 0.24 m (Fig. 3), consistent with the SWOT mission accuracy requirements.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 4 Discussion and Conclusion
“the maximum bias of 0.42 m corresponds to approximately 22 %”
§ 3 Results
“bias values ranging from −0.30 to 0.43 m”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3 Results
“For cycle 508, a comparison between SWOT-derived WSEs and LISFLOOD-FP simulations prior to any adjustment of the Des Mares tributary inflow shows a bias of 1.30 m and an RMSE of −1.21 m.”
§ 2 Methods > 2.4 SWOT data analysis
“Root Mean Square Error (RMSE), used to assess consistency between the values produced by the LISFLOOD-FP hydraulic model and those measured by the SWOT satellite”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 4 Discussion and Conclusion
“The pre- and post-flood cycles (503–507, and 511–514), as well as cycle 509 in the recession phase, show good agreement between the WSEs observed by SWOT and those simulated by the LISFLOOD-FP model.”
§ 2 Methods > 2.4 SWOT data analysis
“Cycles 504–505 lack valid data and Cycle 510 was excluded after filtering.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 4 Discussion and Conclusion
“Regarding dark_frac, almost all nodes have values equal to 0, with only three points above zero (≤ 0.3 m).”
§ 4 Discussion and Conclusion
“the second, dark_frac (Fig. 6B), corresponds to the fraction of “dark water” pixels used in the retrieval, expressed as a unitless ratio between 0 and 1.”
1 more finding
Create a free account to see every finding of this check.
Citations
Cites
A simple raster-based model for flood inundation simulation
Bates, P. D., & De Roo, A. P. J. (2000) · Journal of Hydrology · doi:10.1016/s0022-1694(00)00278-x · Cited by 1,460
Flood inundation modelling: A review of methods, recent advances and uncertainty analysis
Teng, J., Jakeman, A. J., Vaze, J., Croke, B. F. W., Dutta, D., & Kim, S. (2017) · Environmental Modelling & Software · doi:10.1016/j.envsoft.2017.01.006 · Cited by 1,456
Bates, P. D., Horritt, M. S., & Fewtrell, T. J. (2010) · Journal of Hydrology · doi:10.1016/j.jhydrol.2010.03.027 · Cited by 1,273
Detecting, Extracting, and Monitoring Surface Water From Space Using Optical Sensors: A Review
Huang, C., Chen, Y., Zhang, S., & Wu, J. (2018) · Reviews of Geophysics · doi:10.1029/2018rg000598 · Cited by 794
Pappenberger, F., Beven, K., Horritt, M., & Blazkova, S. (2005) · Journal of Hydrology · doi:10.1016/j.jhydrol.2004.06.036 · Cited by 516
Fu, L., Pavelsky, T. M., Crétaux, J., Morrow, R. A., Farrar, J. T., Vaze, P. V., Sengenes, P., Vinogradova‐Shiffer, N., Sylvestre‐Baron, A., Picot, N., et al. (2024) · Geophysical Research Letters · doi:10.1029/2023gl107652 · Cited by 491
Developments in hydrometric network design: A review
Mishra, A., & Coulibaly, P. (2009) · Reviews of Geophysics · doi:10.1029/2007rg000243 · Cited by 402
Predicting floodplain inundation: raster‐based modelling versus the finite‐element approach
Horritt, M. S., & Bates, P. D. (2001) · Hydrological Processes · doi:10.1002/hyp.188 · Cited by 340
Altenau, E. H., Pavelsky, T. M., Durand, M. T., Yang, X., Frasson, R. P. D. M., & Bendezu, L. (2021) · Water Resources Research · doi:10.1029/2021wr030054 · Cited by 317
Khakbaz, B., Imam, B., Hsu, K., & Sorooshian, S. (2009) · Journal of Hydrology · doi:10.1016/j.jhydrol.2009.02.021 · Cited by 193
Cited by
Evaluating SWOT Satellite Data With Gage Information in the United States and Canada
Harlan, M. E., Bjerklie, D. M., Eggleston, J. R., Feng, D., Riggs, R., Bennitt, F. B., Cazals, C., Dudley, R. W., Durand, M., Friedmann, E., et al. (2026) · Water Resources Research · doi:10.1029/2025wr041915 · Cited by 1
Evaluating the SWOT Mission for 3D-Flood Mapping Using Quality FlagsPreprint
Wang, Z., Neal, J., Zhang, C., & Atkinson, P. M. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6215470
Evaluating the SWOT Mission for 3D-Flood Mapping Using Quality FlagsPreprint
Wang, Z., Neal, J., Zhang, C., & Atkinson, P. M. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6439522
SWOT, Empiricism, and River Modeling
Gleason, C. J., Bates, P., Durand, M., Feng, D., Getirana, A., Lin, P., Oubanas, H., Pavelsky, T. M., Shen, C., Smith, L. C., et al. (2026) · Geophysical Research Letters · doi:10.1029/2026gl124323
Metadata
- Authors
- Mzoughi, A., Trudel, M., Biron, P. M., Choné, G., & Siles, G. L.
- Affiliations
- Université de Sherbrooke (CA)
- Concordia University (CA)
- Université Laval (CA)
- Corresponding author
- Mzoughi, Amal
- Venue
- Hydrology and Earth System Sciences
- Publisher
- Copernicus GmbH
- Published
- 2026-07-01
- Volume
- 30
- Issue
- 12
- Pages
- 4141-4155
- ISSN
- 1027-5606 (ISSN-L)
- 1607-7938
- OpenAlex
- W7167537509
- Cited by
- 8
- References
- 46
- Citations by year
- 2026: 8
- FWCI
- 11.27
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Hydrology and earth system sciences (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Funders
- Canadian Space Agency (24AO3SHE16)
- Topics
- Physical Sciences › Environmental Science › Global and Planetary Change › Flood Risk Assessment and Management
- Physical Sciences › Environmental Science › Water Science and Technology › Hydrology and Watershed Management Studies
- Physical Sciences › Environmental Science › Environmental Engineering › Soil Moisture and Remote Sensing
- Keywords
- SWOT mission, water level, flood monitoring, LISFLOOD-FP, hydraulic modeling, satellite altimetry validation, flood discharge estimation, data-scarce conditions, St. Lawrence River, flood risk management, tide gauge
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-11-19, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-11-19 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Assessment of SWOT water surface elevations for flood monitoring of a narrow river ( < 50 m width). https://app.cochat.ai/papers/10.5194/hess-30-4141-2026
- The paper
- Mzoughi, A., Trudel, M., Biron, P. M., Choné, G., & Siles, G. L. (2026). Assessment of SWOT water surface elevations for flood monitoring of a narrow river ( < 50 m width). Hydrology and Earth System Sciences. https://doi.org/10.5194/hess-30-4141-2026
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.