The DOI matches its Crossref record; 11 of the 11 references it cites were found in a registry or an index.
Effect of SLM Parameters on Transformation Temperatures of Shape Memory Nickel Titanium Parts
Abstract
Selective laser melting (SLM) is used to manufacture dense nickel titanium (NiTi) parts. The reversible martensitic transformation of the NiTi parts is investigated with various SLM parameters. The parameters are in the same energy density range, composed of high laser parameters (HP: high laser power adjusted to high scanning speed) and low laser parameters (LP: low laser power adjusted to low scanning speed). The results are linked to the mechanical behavior and shape memory response achieved from compression and dilatometry tests. It is shown that the products may exhibit distinct transformation temperatures depending on the used SLM parameters. The atomized powders and the HP SLM parts with dominant pseudoelastic properties contain austenite at room temperature (due to their lower transformation temperatures), in contrast to the large thermal memory of the LP parts originating from martensitic phases (corresponding to higher transformation temperatures). The post‐annealed samples undergo transformations in a comparable temperature range, implying no significant effect of SLM on composition of the originally used powder. The possible origin of the above findings is postulated and discussed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
An overview of nitinol medical applications
Duerig, T., Pelton, A., & Stöckel, D. (1999) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(99)00294-4 · Cited by 1,628
Selective laser melting of iron-based powder
Kruth, J. P., Froyen, L., Van Vaerenbergh, J., Mercelis, P., Rombouts, M., & Lauwers, B. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2003.11.051 · Cited by 1,550
Self-citationConsolidation phenomena in laser and powder-bed based layered manufacturing
Kruth, J.-P., Levy, G., Klocke, F., & Childs, T. H. C. (2007) · CIRP Annals · doi:10.1016/j.cirp.2007.10.004 · Cited by 1,444
Self-citationManufacturing and processing of NiTi implants: A review
Elahinia, M. H., Hashemi, M., Tabesh, M., & Bhaduri, S. B. (2012) · Progress in Materials Science · doi:10.1016/j.pmatsci.2011.11.001 · Cited by 1,067
Influence of Ni on martensitic phase transformations in NiTi shape memory alloys
Frenzel, J., George, E. P., Dlouhy, A., Somsen, C., Wagner, M. F.-X., & Eggeler, G. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.019 · Cited by 1,004
Non-medical applications of shape memory alloys
Van Humbeeck, J. (1999) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(99)00293-2 · Cited by 837
Self-citationFundamentals of Selective Laser Melting of alloyed steel powders
Rombouts, M., Kruth, J. P., Froyen, L., & Mercelis, P. (2006) · CIRP Annals · doi:10.1016/s0007-8506(07)60395-3 · Cited by 400
Self-citationThe mechanism of multistage martensitic transformations in aged Ni-rich NiTi shape memory alloys
Khalil‐Allafi, J., Ren, X., & Eggeler, G. (2002) · Acta Materialia · doi:10.1016/s1359-6454(01)00385-8 · Cited by 356
Tailoring Selective Laser Melting Process Parameters for NiTi Implants
Bormann, T., Schumacher, R., Müller, B., Mertmann, M., & de Wild, M. (2012) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-012-0318-9 · Cited by 212
The biocompatibility of dense and porous Nickel–Titanium produced by selective laser melting
Habijan, T., Haberland, C., Meier, H., Frenzel, J., Wittsiepe, J., Wuwer, C., Greulich, C., Schildhauer, T. A., & Köller, M. (2013) · Materials Science and Engineering: C · doi:10.1016/j.msec.2012.09.008 · Cited by 206
Cited by
Advances in 4D Printing: Materials and Applications
Kuang, X., Roach, D. J., Wu, J., Hamel, C. M., Ding, Z., Wang, T., Dunn, M. L., & Qi, H. J. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201805290 · Cited by 1,095
3D printing of smart materials: A review on recent progresses in 4D printing
Khoo, Z. X., Teoh, J. E. M., Liu, Y., Chua, C. K., Yang, S., An, J., Leong, K. F., & Yeong, W. Y. (2015) · Virtual and Physical Prototyping · doi:10.1080/17452759.2015.1097054 · Cited by 912
Fabrication of NiTi through additive manufacturing: A review
Elahinia, M., Shayesteh Moghaddam, N., Taheri Andani, M., Amerinatanzi, A., Bimber, B. A., & Hamilton, R. F. (2016) · Progress in Materials Science · doi:10.1016/j.pmatsci.2016.08.001 · Cited by 890
Developments in 4D-printing: a review on current smart materials, technologies, and applications
Zhang, Z., Demir, K. G., & Gu, G. X. (2019) · International Journal of Smart and Nano Materials · doi:10.1080/19475411.2019.1591541 · Cited by 392
Multi-scale defects in powder-based additively manufactured metals and alloys
Fu, J., Li, H., Song, X., & Fu, M. W. (2022) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2022.02.015 · Cited by 391
Metadata
- Authors
- Dadbakhsh, S., Speirs, M., Kruth, J., Schrooten, J., Luyten, J., & Van Humbeeck, J.
- Venue
- Advanced Engineering Materials
- Publisher
- Wiley
- Published
- 2014-03-25
- Volume
- 16
- Issue
- 9
- Pages
- 1140-1146
- ISSN
- 1438-1656 (ISSN-L)
- 1527-2648
- OpenAlex
- W2163436061
- Cited by
- 263
- References
- 11
- FWCI
- 4.32
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of SLM Parameters on Transformation Temperatures of Shape Memory Nickel Titanium Parts. https://app.cochat.ai/papers/10.1002/adem.201300558
- The paper
- Dadbakhsh, S., Speirs, M., Kruth, J., Schrooten, J., Luyten, J., & Van Humbeeck, J. (2014). Effect of SLM Parameters on Transformation Temperatures of Shape Memory Nickel Titanium Parts. Advanced Engineering Materials. https://doi.org/10.1002/adem.201300558
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.