The DOI matches its Crossref record; 41 of the 41 references it cites were found in a registry or an index.
3D‐Printed, All‐in‐One Evaporator for High‐Efficiency Solar Steam Generation under 1 Sun Illumination
Abstract
Using solar energy to generate steam is a clean and sustainable approach to addressing the issue of water shortage. The current challenge for solar steam generation is to develop easy‐to‐manufacture and scalable methods which can convert solar irradiation into exploitable thermal energy with high efficiency. Although various material and structure designs have been reported, high efficiency in solar steam generation usually can be achieved only at concentrated solar illumination. For the first time, 3D printing to construct an all‐in‐one evaporator with a concave structure for high‐efficiency solar steam generation under 1 sun illumination is used. The solar‐steam‐generation device has a high porosity (97.3%) and efficient broadband solar absorption (>97%). The 3D‐printed porous evaporator with intrinsic low thermal conductivity enables heat localization and effectively alleviates thermal dissipation to the bulk water. As a result, the 3D‐printed evaporator has a high solar steam efficiency of 85.6% under 1 sun illumination (1 kW m−2), which is among the best compared with other reported evaporators. The all‐in‐one structure design using the advanced 3D printing fabrication technique offers a new approach to solar energy harvesting for high‐efficiency steam generation.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Solar steam generation by heat localization
Ghasemi, H., Ni, G., Marconnet, A. M., Loomis, J., Yerci, S., Miljkovic, N., & Chen, G. (2014) · Nature Communications · doi:10.1038/ncomms5449 · Cited by 2,333
3D self-assembly of aluminium nanoparticles for plasmon-enhanced solar desalination
Zhou, L., Tan, Y., Wang, J., Xu, W., Yuan, Y., Cai, W., Zhu, S., & Zhu, J. (2016) · Nature Photonics · doi:10.1038/nphoton.2016.75 · Cited by 2,148
Bone tissue engineering using 3D printing
Bose, S., Vahabzadeh, S., & Bandyopadhyay, A. (2013) · Materials Today · doi:10.1016/j.mattod.2013.11.017 · Cited by 1,866
Inkjet Printing for Materials and Devices
Calvert, P. (2001) · Chemistry of Materials · doi:10.1021/cm0101632 · Cited by 1,822
3D‐Printing of Lightweight Cellular Composites
Compton, B. G., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201401804 · Cited by 1,626
Embedded 3D Printing of Strain Sensors within Highly Stretchable Elastomers
Muth, J. T., Vogt, D. M., Truby, R. L., Mengüç, Y., Kolesky, D. B., Wood, R. J., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201400334 · Cited by 1,611
3D Printing of Interdigitated Li‐Ion Microbattery Architectures
Sun, K., Wei, T., Ahn, B. Y., Seo, J. Y., Dillon, S. J., & Lewis, J. A. (2013) · Advanced Materials · doi:10.1002/adma.201301036 · Cited by 1,341
Self-assembly of highly efficient, broadband plasmonic absorbers for solar steam generation
Zhou, L., Tan, Y., Ji, D., Zhu, B., Zhang, P., Xu, J., Gan, Q., Yu, Z., & Zhu, J. (2016) · Science Advances · doi:10.1126/sciadv.1501227 · Cited by 1,327
Beidaghi, M., & Gogotsi, Y. (2014) · Energy & Environmental Science · doi:10.1039/c3ee43526a · Cited by 1,293
Li, X., Xu, W., Tang, M., Zhou, L., Zhu, B., Zhu, S., & Zhu, J. (2016) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1613031113 · Cited by 1,246
Steam generation under one sun enabled by a floating structure with thermal concentration
Ni, G., Li, G., Boriskina, S. V., Li, H., Yang, W., Zhang, T., & Chen, G. (2016) · Nature Energy · doi:10.1038/nenergy.2016.126 · Cited by 1,181
Highly compressible 3D periodic graphene aerogel microlattices
Zhu, C., Han, T. Y.-J., Duoss, E. B., Golobic, A. M., Kuntz, J. D., Spadaccini, C. M., & Worsley, M. A. (2015) · Nature Communications · doi:10.1038/ncomms7962 · Cited by 1,148
High‐Performance Photothermal Conversion of Narrow‐Bandgap Ti2O3 Nanoparticles
Wang, J., Li, Y., Deng, L., Wei, N., Weng, Y., Dong, S., Qi, D., Qiu, J., Chen, X., & Wu, T. (2017) · Advanced Materials · doi:10.1002/adma.201603730 · Cited by 1,056
Self-citationTailoring Graphene Oxide‐Based Aerogels for Efficient Solar Steam Generation under One Sun
Hu, X., Xu, W., Zhou, L., Tan, Y., Wang, Y., Zhu, S., & Zhu, J. (2017) · Advanced Materials · doi:10.1002/adma.201604031 · Cited by 978
Multifunctional Porous Graphene for High‐Efficiency Steam Generation by Heat Localization
Ito, Y., Tanabe, Y., Han, J., Fujita, T., Tanigaki, K., & Chen, M. (2015) · Advanced Materials · doi:10.1002/adma.201501832 · Cited by 935
All‐Organic Vapor Sensor Using Inkjet‐Printed Reduced Graphene Oxide
Dua, V., Surwade, S. P., Ammu, S., Agnihotra, S. R., Jain, S., Roberts, K. E., Park, S., Ruoff, R. S., & Manohar, S. K. (2010) · Angewandte Chemie International Edition · doi:10.1002/anie.200905089 · Cited by 932
3D Printing of Highly Stretchable and Tough Hydrogels into Complex, Cellularized Structures
Hong, S., Sycks, D., Chan, H. F., Lin, S., Lopez, G. P., Guilak, F., Leong, K. W., & Zhao, X. (2015) · Advanced Materials · doi:10.1002/adma.201501099 · Cited by 873
A Bioinspired, Reusable, Paper‐Based System for High‐Performance Large‐Scale Evaporation
Liu, Y., Yu, S., Feng, R., Bernard, A., Liu, Y., Zhang, Y., Duan, H., Shang, W., Tao, P., Song, C., et al. (2015) · Advanced Materials · doi:10.1002/adma.201500135 · Cited by 814
Graphene Oxide‐Based Electrode Inks for 3D‐Printed Lithium‐Ion Batteries
Fu, K., Wang, Y., Yan, C., Yao, Y., Chen, Y., Dai, J., Lacey, S., Wang, Y., Wan, J., Li, T., et al. (2016) · Advanced Materials · doi:10.1002/adma.201505391 · Cited by 758
Self-citationSupercapacitors Based on Three-Dimensional Hierarchical Graphene Aerogels with Periodic Macropores
Zhu, C., Liu, T., Qian, F., Han, T. Y.-J., Duoss, E. B., Kuntz, J. D., Spadaccini, C. M., Worsley, M. A., & Li, Y. (2016) · Nano Letters · doi:10.1021/acs.nanolett.5b04965 · Cited by 720
Self-citationJakus, A. E., Secor, E. B., Rutz, A. L., Jordan, S. W., Hersam, M. C., & Shah, R. N. (2015) · ACS Nano · doi:10.1021/acsnano.5b01179 · Cited by 710
Bio-ink properties and printability for extrusion printing living cells
Chung, J. H. Y., Naficy, S., Yue, Z., Kapsa, R., Quigley, A., Moulton, S. E., & Wallace, G. G. (2013) · Biomaterials Science · doi:10.1039/c3bm00012e · Cited by 610
Farahani, R. D., Dubé, M., & Therriault, D. (2016) · Advanced Materials · doi:10.1002/adma.201506215 · Cited by 604
Bilayered Biofoam for Highly Efficient Solar Steam Generation
Jiang, Q., Tian, L., Liu, K., Tadepalli, S., Raliya, R., Biswas, P., Naik, R. R., & Singamaneni, S. (2016) · Advanced Materials · doi:10.1002/adma.201601819 · Cited by 542
3D Printing of Graphene Aerogels
Zhang, Q., Zhang, F., Medarametla, S. P., Li, H., Zhou, C., & Lin, D. (2016) · Small · doi:10.1002/smll.201503524 · Cited by 532
Novel Nanostructured Paper with Ultrahigh Transparency and Ultrahigh Haze for Solar Cells
Fang, Z., Zhu, H., Yuan, Y., Ha, D., Zhu, S., Preston, C., Chen, Q., Li, Y., Han, X., Lee, S., et al. (2014) · Nano Letters · doi:10.1021/nl404101p · Cited by 489
Self-citationCompact solar autoclave based on steam generation using broadband light-harvesting nanoparticles
Neumann, O., Feronti, C., Neumann, A. D., Dong, A., Schell, K., Lu, B., Kim, E., Quinn, M., Thompson, S., Grady, N., et al. (2013) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1310131110 · Cited by 471
Liu, Y., Chen, J., Guo, D., Cao, M., & Jiang, L. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b03435 · Cited by 372
Graphene oxide dispersions: tuning rheology to enable fabrication
Naficy, S., Jalili, R., Aboutalebi, S. H., Gorkin III, R. A., Konstantinov, K., Innis, P. C., Spinks, G. M., Poulin, P., & Wallace, G. G. (2014) · Mater. Horiz. · doi:10.1039/c3mh00144j · Cited by 368
Wang, L., Jia, X., Li, Y., Yang, F., Zhang, L., Liu, L., Ren, X., & Yang, H. (2014) · Journal of Materials Chemistry A · doi:10.1039/c4ta02815e · Cited by 347
Self-citationQuantifying the potential of ultra-permeable membranes for water desalination
Cohen-Tanugi, D., McGovern, R. K., Dave, S. H., Lienhard, J. H., & Grossman, J. C. (2014) · Energy Environ. Sci. · doi:10.1039/c3ee43221a · Cited by 341
An overview of the suitability of hydrogel-forming polymers for extrusion-based 3D-printing
Kirchmajer, D. M., Gorkin III, R., & in het Panhuis, M. (2015) · Journal of Materials Chemistry B · doi:10.1039/c5tb00393h · Cited by 337
Zhou, L., Zhuang, S., He, C., Tan, Y., Wang, Z., & Zhu, J. (2017) · Nano Energy · doi:10.1016/j.nanoen.2016.12.031 · Cited by 307
Printing in Three Dimensions with Graphene
García‐Tuñon, E., Barg, S., Franco, J., Bell, R., Eslava, S., D'Elia, E., Maher, R. C., Guitian, F., & Saiz, E. (2015) · Advanced Materials · doi:10.1002/adma.201405046 · Cited by 303
3D Printing of Reduced Graphene Oxide Nanowires
Kim, J. H., Chang, W. S., Kim, D., Yang, J. R., Han, J. T., Lee, G., Kim, J. T., & Seol, S. K. (2015) · Advanced Materials · doi:10.1002/adma.201404380 · Cited by 258
Reduced Graphene Oxide Films with Ultrahigh Conductivity as Li-Ion Battery Current Collectors
Chen, Y., Fu, K., Zhu, S., Luo, W., Wang, Y., Li, Y., Hitz, E., Yao, Y., Dai, J., Wan, J., et al. (2016) · Nano Letters · doi:10.1021/acs.nanolett.6b00743 · Cited by 251
Self-citationPlasmonic Biofoam: A Versatile Optically Active Material
Tian, L., Luan, J., Liu, K.-K., Jiang, Q., Tadepalli, S., Gupta, M. K., Naik, R. R., & Singamaneni, S. (2016) · Nano Letters · doi:10.1021/acs.nanolett.5b04320 · Cited by 186
Fiber reinforcement during 3D printing
Christ, S., Schnabel, M., Vorndran, E., Groll, J., & Gbureck, U. (2015) · Materials Letters · doi:10.1016/j.matlet.2014.10.065 · Cited by 183
Flexible artificially-networked structure for ambient/high pressure solar steam generation
Sajadi, S. M., Farokhnia, N., Irajizad, P., Hasnain, M. A., & Ghasemi, H. (2016) · Journal of Materials Chemistry A · doi:10.1039/c6ta01205a · Cited by 149
A low-energy forward osmosis process to produce drinking water
Liu, Z., Bai, H., Lee, J., & Sun, D. D. (2011) · Energy & Environmental Science · doi:10.1039/c1ee01186c · Cited by 139
Magnetically ultraresponsive nanoscavengers for next-generation water purification systems
Zhang, M., Xie, X. H., Tang, M., et al. (2013) · Nature Communications · doi:10.1038/ncomms2892 · Cited by 92
Cited by
Solar-driven interfacial evaporation
Tao, P., Ni, G., Song, C., Shang, W., Wu, J., Zhu, J., Chen, G., & Deng, T. (2018) · Nature Energy · doi:10.1038/s41560-018-0260-7 · Cited by 2,380
Gao, M., Zhu, L., Peh, C. K., & Ho, G. W. (2019) · Energy & Environmental Science · doi:10.1039/c8ee01146j · Cited by 1,991
Photothermal Nanomaterials: A Powerful Light-to-Heat Converter
Cui, X., Ruan, Q., Zhuo, X., Xia, X., Hu, J., Fu, R., Li, Y., Wang, J., & Xu, H. (2023) · Chemical Reviews · doi:10.1021/acs.chemrev.3c00159 · Cited by 1,944
Self-citationMaterials for solar-powered water evaporation
Zhao, F., Guo, Y., Zhou, X., Shi, W., & Yu, G. (2020) · Nature Reviews Materials · doi:10.1038/s41578-020-0182-4 · Cited by 1,541
Challenges and Opportunities for Solar Evaporation
Chen, C., Kuang, Y., & Hu, L. (2019) · Joule · doi:10.1016/j.joule.2018.12.023 · Cited by 1,518
Self-citation
Metadata
- Authors
- Li, Y., Gao, T., Yang, Z., Chen, C., Luo, W., Song, J., Hitz, E., Jia, C., Zhou, Y., Liu, B., Yang, B., & Hu, L.
- Venue
- Advanced Materials
- Publisher
- Wiley
- Published
- 2017-05-04
- Volume
- 29
- Issue
- 26
- ISSN
- 0935-9648 (ISSN-L)
- 1521-4095
- OpenAlex
- W2611941517
- Cited by
- 720
- References
- 41
- FWCI
- 22.27
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.