The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Elevated‐Temperature 3D Printing of Hybrid Solid‐State Electrolyte for Li‐Ion Batteries
Abstract
While 3D printing of rechargeable batteries has received immense interest in advancing the next generation of 3D energy storage devices, challenges with the 3D printing of electrolytes still remain. Additional processing steps such as solvent evaporation were required for earlier studies of electrolyte fabrication, which hindered the simultaneous production of electrode and electrolyte in an all‐3D‐printed battery. Here, a novel method is demonstrated to fabricate hybrid solid‐state electrolytes using an elevated‐temperature direct ink writing technique without any additional processing steps. The hybrid solid‐state electrolyte consists of solid poly(vinylidene fluoride‐hexafluoropropylene) matrices and a Li+‐conducting ionic‐liquid electrolyte. The ink is modified by adding nanosized ceramic fillers to achieve the desired rheological properties. The ionic conductivity of the inks is 0.78 × 10 −3 S cm−1. Interestingly, a continuous, thin, and dense layer is discovered to form between the porous electrolyte layer and the electrode, which effectively reduces the interfacial resistance of the solid‐state battery. Compared to the traditional methods of solid‐state battery assembly, the directly printed electrolyte helps to achieve higher capacities and a better rate performance. The direct fabrication of electrolyte from printable inks at an elevated temperature will shed new light on the design of all‐3D‐printed batteries for next‐generation electronic devices.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Lithium Batteries: Status, Prospects and Future
Scrosati, B., & Garche, J. (2010) · Journal of Power Sources · doi:10.1016/j.jpowsour.2009.11.048 · Cited by 5,153
Evaluation of 3D Printing and Its Potential Impact on Biotechnology and the Chemical Sciences
Gross, B. C., Erkal, J. L., Lockwood, S. Y., Chen, C., & Spence, D. M. (2014) · Analytical Chemistry · doi:10.1021/ac403397r · Cited by 1,746
Cited by
Direct Ink Writing: A 3D Printing Technology for Diverse Materials
Saadi, M. A. S. R., Maguire, A., Pottackal, N. T., Thakur, M. S. H., Ikram, M. M., Hart, A. J., Ajayan, P. M., & Rahman, M. M. (2022) · Advanced Materials · doi:10.1002/adma.202108855 · Cited by 1,335
Extrusion 3D Printing of Polymeric Materials with Advanced Properties
Jiang, Z., Diggle, B., Tan, M. L., Viktorova, J., Bennett, C. W., & Connal, L. A. (2020) · Advanced Science · doi:10.1002/advs.202001379 · Cited by 408
Recent progress on solid-state hybrid electrolytes for solid-state lithium batteries
Liang, J., Luo, J., Sun, Q., Yang, X., Li, R., & Sun, X. (2019) · Energy Storage Materials · doi:10.1016/j.ensm.2019.06.021 · Cited by 365
Fan, X., Zhong, C., Liu, J., Ding, J., Deng, Y., Han, X., Zhang, L., Hu, W., Wilkinson, D. P., & Zhang, J. (2022) · Chemical Reviews · doi:10.1021/acs.chemrev.2c00196 · Cited by 347
3D Printed High‐Performance Lithium Metal Microbatteries Enabled by Nanocellulose
Cao, D., Xing, Y., Tantratian, K., Wang, X., Ma, Y., Mukhopadhyay, A., Cheng, Z., Zhang, Q., Jiao, Y., Chen, L., et al. (2019) · Advanced Materials · doi:10.1002/adma.201807313 · Cited by 337
Metadata
- Authors
- Cheng, M., Jiang, Y., Yao, W., Yuan, Y., Deivanayagam, R., Foroozan, T., Huang, Z., Song, B., Rojaee, R., Shokuhfar, T., Pan, Y., Lu, J., & Shahbazian‐Yassar, R.
- Venue
- Advanced Materials
- Publisher
- Wiley
- Published
- 2018-08-21
- Volume
- 30
- Issue
- 39
- Pages
- e1800615-e1800615
- ISSN
- 0935-9648 (ISSN-L)
- 1521-4095
- OpenAlex
- W2888385459
- Cited by
- 214
- References
- 2
- FWCI
- 8.00
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Elevated‐Temperature 3D Printing of Hybrid Solid‐State Electrolyte for Li‐Ion Batteries. https://app.cochat.ai/papers/10.1002/adma.201800615
- The paper
- Cheng, M., Jiang, Y., Yao, W., Yuan, Y., Deivanayagam, R., Foroozan, T., Huang, Z., Song, B., Rojaee, R., Shokuhfar, T., Pan, Y., Lu, J., & Shahbazian‐Yassar, R. (2018). Elevated‐Temperature 3D Printing of Hybrid Solid‐State Electrolyte for Li‐Ion Batteries. Advanced Materials. https://doi.org/10.1002/adma.201800615
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.