The DOI matches its Crossref record; 20 of the 20 references it cites were found in a registry or an index.
3D Plate‐Lattices: An Emerging Class of Low‐Density Metamaterial Exhibiting Optimal Isotropic Stiffness
Open accessAbstract
In lightweight engineering, there is a constant quest for low‐density materials featuring high mass‐specific stiffness and strength. Additively‐manufactured metamaterials are particularly promising candidates as the controlled introduction of porosity allows for tailoring their density while activating strengthening size‐effects at the nano‐ and microstructural level. Here, plate‐lattices are conceived by placing plates along the closest‐packed planes of crystal structures. Based on theoretical analysis, a general design map is developed for elastically isotropic plate‐lattices of cubic symmetry. In addition to validating the design map, detailed computational analysis reveals that there even exist plate‐lattice compositions that provide nearly isotropic yield strength together with elastic isotropy. The most striking feature of plate‐lattices is that their stiffness and yield strength are within a few percent of the theoretical limits for isotropic porous solids. This implies that the stiffness of isotropic plate‐lattices is up to three times higher than that of the stiffest truss‐lattices of equal mass. This stiffness advantage is also confirmed by experiments on truss‐ and plate‐lattice specimens fabricated through direct laser writing. Due to their porous internal structure, the potential impact of the new metamaterials reported here goes beyond lightweight engineering, including applications for heat‐exchange, thermal insulation, acoustics, and biomedical engineering.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A variational approach to the theory of the elastic behaviour of multiphase materials
Hashin, Z., & Shtrikman, S. (1963) · Journal of the Mechanics and Physics of Solids · doi:10.1016/0022-5096(63)90060-7 · Cited by 5,882
Cellular Solids: Structure and Properties
Gibson, L. J., & Ashby, M. F. (1997) · Cambridge University Press eBooks · doi:10.1017/cbo9781139878326 · Cited by 5,512
Bioinspired structural materials
Wegst, U. G. K., Bai, H., Saiz, E., Tomsia, A. P., & Ritchie, R. O. (2015) · Nature Materials · doi:10.1038/nmat4089 · Cited by 4,721
Ultralight, ultrastiff mechanical metamaterials
Zheng, X., Lee, H., Weisgraber, T. H., Shusteff, M., DeOtte, J., Duoss, E. B., Kuntz, J. D., Biener, M. M., Ge, Q., Jackson, J. A., et al. (2014) · Science · doi:10.1126/science.1252291 · Cited by 2,308
Effective properties of the octet-truss lattice material
Deshpande, V. S., Fleck, N. A., & Ashby, M. F. (2001) · Journal of the Mechanics and Physics of Solids · doi:10.1016/s0022-5096(01)00010-2 · Cited by 1,741
Foam topology: bending versus stretching dominated architectures
Deshpande, V. S., Ashby, M. F., & Fleck, N. A. (2001) · Acta Materialia · doi:10.1016/s1359-6454(00)00379-7 · Cited by 1,623
Strong, lightweight, and recoverable three-dimensional ceramic nanolattices
Meza, L. R., Das, S., & Greer, J. R. (2014) · Science · doi:10.1126/science.1255908 · Cited by 1,498
Strong, tough and stiff bioinspired ceramics from brittle constituents
Bouville, F., Maire, E., Meille, S., Van de Moortèle, B., Stevenson, A. J., & Deville, S. (2014) · Nature Materials · doi:10.1038/nmat3915 · Cited by 959
Mechanical metamaterials at the theoretical limit of isotropic elastic stiffness
Berger, J. B., Wadley, H. N. G., & McMeeking, R. M. (2017) · Nature · doi:10.1038/nature21075 · Cited by 914
Tancogne-Dejean, T., Spierings, A. B., & Mohr, D. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.05.054 · Cited by 806
Self-citation
Cited by
SLM lattice structures: Properties, performance, applications and challenges
Maconachie, T., Leary, M., Lozanovski, B., Zhang, X., Qian, M., Faruque, O., & Brandt, M. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108137 · Cited by 1,497
Advanced lightweight materials for Automobiles: A review
Zhang, W., & Xu, J. (2022) · Materials & Design · doi:10.1016/j.matdes.2022.110994 · Cited by 1,147
Multifunctional Mechanical Metamaterials Based on Triply Periodic Minimal Surface Lattices
Al-Ketan, O., & Abu Al-Rub, R. K. (2019) · Advanced Engineering Materials · doi:10.1002/adem.201900524 · Cited by 887
Mechanical metamaterials and beyond
Jiao, P., Mueller, J., Raney, J. R., Zheng, X., & Alavi, A. H. (2023) · Nature Communications · doi:10.1038/s41467-023-41679-8 · Cited by 733
Inverse-designed spinodoid metamaterials
Kumar, S., Tan, S., Zheng, L., & Kochmann, D. M. (2020) · npj Computational Materials · doi:10.1038/s41524-020-0341-6 · Cited by 444
Metadata
- Authors
- Tancogne‐Dejean, T., Diamantopoulou, M., Gorji, M. B., Bonatti, C., & Mohr, D.
- Venue
- Advanced Materials
- Publisher
- Wiley
- Published
- 2018-09-19
- Volume
- 30
- Issue
- 45
- Pages
- e1803334-e1803334
- ISSN
- 0935-9648 (ISSN-L)
- 1521-4095
- OpenAlex
- W2891254673
- Cited by
- 506
- References
- 20
- FWCI
- 19.19
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: 3D Plate‐Lattices: An Emerging Class of Low‐Density Metamaterial Exhibiting Optimal Isotropic Stiffness. https://app.cochat.ai/papers/10.1002/adma.201803334
- The paper
- Tancogne‐Dejean, T., Diamantopoulou, M., Gorji, M. B., Bonatti, C., & Mohr, D. (2018). 3D Plate‐Lattices: An Emerging Class of Low‐Density Metamaterial Exhibiting Optimal Isotropic Stiffness. Advanced Materials. https://doi.org/10.1002/adma.201803334
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.