The DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index.
Interstitial Point Defect Scattering Contributing to High Thermoelectric Performance in SnTe
Abstract
Due to point defect phonon scattering, formation of solid solutions has long been considered as an effective approach for enhancing thermoelectric performance through reducing the lattice thermal conductivity. The scattering of phonons by point defects mainly comes from the mass and strain fluctuations between the guest and the host atoms. Both the fluctuations can be maximized by point defects of interstitial atoms and/or vacancies in a crystal. Here, a demonstration of phonon scattering by interstitial Cu atoms is shown, leading to an extremely low lattice thermal conductivity of 0.5 W m−1 K−1 in SnTe‐Cu 2 Te solid solutions. This is the lowest lattice thermal conductivity reported in SnTe‐based materials so far, which is actually approaching the amorphous limit of SnTe. As a result, a peak thermoelectric figure of merit, zT, higher than 1 is achieved in Sn 0.94 Cu 0.12 Te at 850 K, without relying on other approaches for electrical performance enhancements. The strategy used here is believed to be equally applicable in thermoelectrics with interstitial point defects.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Generalized Gradient Approximation Made Simple
Perdew, J. P., Burke, K., & Ernzerhof, M. (1996) · Physical Review Letters · doi:10.1103/physrevlett.77.3865 · Cited by 215,824
Projector augmented-wave method
Blöchl, P. E. (1994) · Physical Review B · doi:10.1103/physrevb.50.17953 · Cited by 92,732
Kresse, G., & Furthmüller, J. (1996) · Computational Materials Science · doi:10.1016/0927-0256(96)00008-0 · Cited by 75,638
Special points for Brillouin-zone integrations
Monkhorst, H. J., & Pack, J. D. (1976) · Physical Review B · doi:10.1103/physrevb.13.5188 · Cited by 71,721
CRC Handbook of Thermoelectrics
(2018) · CRC Press eBooks · doi:10.1201/9781420049718 · Cited by 5,787
High-Thermoelectric Performance of Nanostructured Bismuth Antimony Telluride Bulk Alloys
Poudel, B., Hao, Q., Ma, Y., Lan, Y., Minnich, A., Yu, B., Yan, X., Wang, D., Muto, A., Vashaee, D., et al. (2008) · Science · doi:10.1126/science.1156446 · Cited by 5,606
Convergence of electronic bands for high performance bulk thermoelectrics
Pei, Y., Shi, X., LaLonde, A., Wang, H., Chen, L., & Snyder, G. J. (2011) · Nature · doi:10.1038/nature09996 · Cited by 4,263
Self-citationEnhancement of Thermoelectric Efficiency in PbTe by Distortion of the Electronic Density of States
Heremans, J. P., Jovovic, V., Toberer, E. S., Saramat, A., Kurosaki, K., Charoenphakdee, A., Yamanaka, S., & Snyder, G. J. (2008) · Science · doi:10.1126/science.1159725 · Cited by 4,161
A simplified method for calculating the debye temperature from elastic constants
Anderson, O. L. (1963) · Journal of Physics and Chemistry of Solids · doi:10.1016/0022-3697(63)90067-2 · Cited by 3,684
Lower limit to the thermal conductivity of disordered crystals
Cahill, D. G., Watson, S. K., & Pohl, R. O. (1992) · Physical Review B · doi:10.1103/physrevb.46.6131 · Cited by 2,617
Copper ion liquid-like thermoelectrics
Liu, H., Shi, X., Xu, F., Zhang, L., Zhang, W., Chen, L., Li, Q., Uher, C., Day, T., & Snyder, G. J. (2012) · Nature Materials · doi:10.1038/nmat3273 · Cited by 2,118
Dense dislocation arrays embedded in grain boundaries for high-performance bulk thermoelectrics
Kim, S. I., Lee, K. H., Mun, H. A., Kim, H. S., Hwang, S. W., Roh, J. W., Yang, D. J., Shin, W. H., Li, X. S., Lee, Y. H., et al. (2015) · Science · doi:10.1126/science.aaa4166 · Cited by 2,084
Band Engineering of Thermoelectric Materials
Pei, Y., Wang, H., & Snyder, G. J. (2012) · Advanced Materials · doi:10.1002/adma.201202919 · Cited by 1,793
Self-citationThe Scattering of Low-Frequency Lattice Waves by Static Imperfections
Klemens, P. G. (1955) · Proceedings of the Physical Society. Section A · doi:10.1088/0370-1298/68/12/303 · Cited by 1,457
Semiconductor thermoelements and thermo-electric cooling
(1960) · Solar Energy · doi:10.1016/0038-092x(60)90073-6 · Cited by 1,177
Effect of Point Imperfections on Lattice Thermal Conductivity
Callaway, J., & von Baeyer, H. C. (1960) · Physical Review · doi:10.1103/physrev.120.1149 · Cited by 1,168
Lattice Thermal Conductivity of Disordered Semiconductor Alloys at High Temperatures
Abeles, B. (1963) · Physical Review · doi:10.1103/physrev.131.1906 · Cited by 1,148
Intrinsically Minimal Thermal Conductivity in CubicI−V−VI2Semiconductors
Morelli, D. T., Jovovic, V., & Heremans, J. P. (2008) · Physical Review Letters · doi:10.1103/physrevlett.101.035901 · Cited by 982
Semiconducting Lead Chalcogenides
Ravich, Y. I., Efimova, B. A., & Smirnov, I. A. (1970) · Springer eBooks · doi:10.1007/978-1-4684-8607-0 · Cited by 904
High thermoelectric performance by resonant dopant indium in nanostructured SnTe
Zhang, Q., Liao, B., Lan, Y., Lukas, K., Liu, W., Esfarjani, K., Opeil, C., Broido, D., Chen, G., & Ren, Z. (2013) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1305735110 · Cited by 789
Tan, G., Zhao, L.-D., Shi, F., Doak, J. W., Lo, S.-H., Sun, H., Wolverton, C., Dravid, V. P., Uher, C., & Kanatzidis, M. G. (2014) · Journal of the American Chemical Society · doi:10.1021/ja500860m · Cited by 706
Low effective mass leading to high thermoelectric performance
Pei, Y., LaLonde, A. D., Wang, H., & Snyder, G. J. (2012) · Energy & Environmental Science · doi:10.1039/c2ee21536e · Cited by 655
Self-citationTellurium as a high-performance elemental thermoelectric
Lin, S., Li, W., Chen, Z., Shen, J., Ge, B., & Pei, Y. (2016) · Nature Communications · doi:10.1038/ncomms10287 · Cited by 518
Self-citationTan, G., Shi, F., Hao, S., Chi, H., Zhao, L.-D., Uher, C., Wolverton, C., Dravid, V. P., & Kanatzidis, M. G. (2015) · Journal of the American Chemical Society · doi:10.1021/jacs.5b00837 · Cited by 502
Extraordinary role of Hg in enhancing the thermoelectric performance of p-type SnTe
Tan, G., Shi, F., Doak, J. W., Sun, H., Zhao, L.-D., Wang, P., Uher, C., Wolverton, C., Dravid, V. P., & Kanatzidis, M. G. (2015) · Energy & Environmental Science · doi:10.1039/c4ee01463d · Cited by 401
High Band Degeneracy Contributes to High Thermoelectric Performance in p‐Type Half‐Heusler Compounds
Fu, C., Zhu, T., Pei, Y., Xie, H., Wang, H., Snyder, G. J., Liu, Y., Liu, Y., & Zhao, X. (2014) · Advanced Energy Materials · doi:10.1002/aenm.201400600 · Cited by 341
Self-citationToher, C., Plata, J. J., Levy, O., de Jong, M., Asta, M., Nardelli, M. B., & Curtarolo, S. (2014) · Physical Review B · doi:10.1103/physrevb.90.174107 · Cited by 315
High Thermoelectric Figure of Merit in PbTe Alloys Demonstrated in PbTe–CdTe
Pei, Y., LaLonde, A. D., Heinz, N. A., & Snyder, G. J. (2012) · Advanced Energy Materials · doi:10.1002/aenm.201100770 · Cited by 289
Self-citationOptimization of thermoelectric efficiency in SnTe: the case for the light band
Zhou, M., Gibbs, Z. M., Wang, H., Han, Y., Xin, C., Li, L., & Snyder, G. J. (2014) · Phys. Chem. Chem. Phys. · doi:10.1039/c4cp02091j · Cited by 270
Thermopower enhancement in Pb1−xMnxTe alloys and its effect on thermoelectric efficiency
Pei, Y., Wang, H., Gibbs, Z. M., LaLonde, A. D., & Snyder, G. J. (2012) · NPG Asia Materials · doi:10.1038/am.2012.52 · Cited by 243
Self-citationTan, G., Zeier, W. G., Shi, F., Wang, P., Snyder, G. J., Dravid, V. P., & Kanatzidis, M. G. (2015) · Chemistry of Materials · doi:10.1021/acs.chemmater.5b03708 · Cited by 225
Band and scattering tuning for high performance thermoelectric Sn1−xMnxTe alloys
Li, W., Chen, Z., Lin, S., Chang, Y., Ge, B., Chen, Y., & Pei, Y. (2015) · Journal of Materiomics · doi:10.1016/j.jmat.2015.09.001 · Cited by 223
Self-citationValence band structure of SnTe
Rogers, L. M. (1968) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/1/7/304 · Cited by 192
Hole contribution to the elastic constants of SnTe
Seddon, T., Gupta, S., & Saunders, G. A. (1976) · Solid State Communications · doi:10.1016/0038-1098(76)91701-4 · Cited by 44
Cited by
Advanced Thermoelectric Design: From Materials and Structures to Devices
Shi, X.-L., Zou, J., & Chen, Z.-G. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00026 · Cited by 2,524
Self-citationMao, J., Liu, Z., Zhou, J., Zhu, H., Zhang, Q., Chen, G., & Ren, Z. (2018) · Advances in Physics · doi:10.1080/00018732.2018.1551715 · Cited by 592
Lattice Dislocations Enhancing Thermoelectric PbTe in Addition to Band Convergence
Chen, Z., Jian, Z., Li, W., Chang, Y., Ge, B., Hanus, R., Yang, J., Chen, Y., Huang, M., Snyder, G. J., et al. (2017) · Advanced Materials · doi:10.1002/adma.201606768 · Cited by 557
Self-citationDefect engineering in thermoelectric materials: what have we learned?
Zheng, Y., Slade, T. J., Hu, L., Tan, X. Y., Luo, Y., Luo, Z.-Z., Xu, J., Yan, Q., & Kanatzidis, M. G. (2021) · Chemical Society Reviews · doi:10.1039/d1cs00347j · Cited by 482
Li, W., Zheng, L., Ge, B., Lin, S., Zhang, X., Chen, Z., Chang, Y., & Pei, Y. (2017) · Advanced Materials · doi:10.1002/adma.201605887 · Cited by 432
Self-citation
Metadata
- Authors
- Pei, Y., Zheng, L., Li, W., Lin, S., Chen, Z., Wang, Y., Xu, X., Yu, H., Chen, Y., & Ge, B.
- Venue
- Advanced Electronic Materials
- Publisher
- Wiley
- Published
- 2016-05-11
- Volume
- 2
- Issue
- 6
- ISSN
- 2199-160X (ISSN-L)
- OpenAlex
- W2375438262
- Cited by
- 306
- References
- 34
- FWCI
- 13.97
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.