Investigation of tool wear and energy consumption in machining Ti6Al4V alloy with uncoated tools
Open accessThe DOI matches its Crossref record; 29 of the 29 references it cites were found in a registry or an index.
Abstract
This research studies the energy consumption and wear mechanism of carbide cutting tools in dry machining of Ti6Al4V alloy. In the first phase of experiments, full factorial design experiments were employed to study the tool wear rate (R) and specific cutting energy (SCE) with respect to the machining conditions (cutting speed and feed rate). Results showed that machining responses such as tool wear and energy consumption are affected by cutting conditions, thus requiring investigation to understand the wear mechanisms. Therefore, in the second phase, additional experiments were performed to investigate the tool-workpiece interactions at the cutting conditions reported to have low, moderate, and high tool wear. It was revealed that strong adhesion and material transfer between the tool and workpiece caused high wear. Electron dispersive X-ray spectroscopy (EDX) analysis of worn tools showed that the transfer of tungsten (W) and cobalt (Co) to the workpiece and titanium to the tool surface is the primary cause of tool deterioration. As a result, diffusion and dissolution have degraded cutting performance and weakened the tool edge, leading to rapid wear. Furthermore, worn tools resulted in relatively higher energy consumption per unit volume of material removed at the tooltip. The degradation of cutting performance and weakening of the tool edge results in rapid wear and higher energy consumption. The study suggests that minimizing tool wear is crucial for energy reduction, improved sustainability, and cleaner production goals in dry machining of titanium-based alloys.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
An overview of the machinability of aeroengine alloys
Ezugwu, E. O., Bonney, J., & Yamane, Y. (2003) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(02)01042-7 · Cited by 1,116
Machinability of titanium alloys (Ti6Al4V and Ti555.3)
Arrazola, P.-J., Garay, A., Iriarte, L.-M., Armendia, M., Marya, S., & Le Maître, F. (2009) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2008.06.020 · Cited by 595
A system model for green manufacturing
Deif, A. M. (2011) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2011.05.022 · Cited by 486
New observations on tool life, cutting forces and chip morphology in cryogenic machining Ti-6Al-4V
Bermingham, M. J., Kirsch, J., Sun, S., Palanisamy, S., & Dargusch, M. S. (2011) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2011.02.009 · Cited by 364
Tool Wear in Titanium Machining
Hartung, P. D., Kramer, B. M., & von Turkovich, B. F. (1982) · CIRP Annals · doi:10.1016/s0007-8506(07)63272-7 · Cited by 309
Development of an energy consumption monitoring procedure for machine tools
Behrendt, T., Zein, A., & Min, S. (2012) · CIRP Annals · doi:10.1016/j.cirp.2012.03.103 · Cited by 226
Machining of Titanium Alloy(Ti-6Al-4V)—Theory to Application
Pramanik, A., & Littlefair, G. (2015) · Machining Science and Technology · doi:10.1080/10910344.2014.991031 · Cited by 191
Tool wear characteristics in turning of titanium alloy Ti-6246
Jawaid, A., Che-Haron, C. H., & Abdullah, A. (1999) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(99)00246-0 · Cited by 181
Diffusion wear in dry cutting of Ti–6Al–4V with WC/Co carbide tools
Jianxin, D., Yousheng, L., & Wenlong, S. (2008) · Wear · doi:10.1016/j.wear.2008.04.024 · Cited by 163
The assessment of plastic deformation in metal cutting
Astakhov, V. P., & Shvets, S. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2003.10.015 · Cited by 163
Research works printed but not linked: 9
- 3. Stephenson DA, Agapiou JS (2023) Metal cutting theory and prac- tice. CRC press
- 9. Goindi G, production PSJ of cleaner, (2017 undefined) Dry machining: a step towards sustainable machining-challenges and future directions. Elsevier [Internet] [cited 2023 Apr 8]; Available from: https:// www. scien cedir ect. com/ scien ce/ artic le/ pii/ S0959 65261 73169 18? casa_ token= J8dLp iJy4E oAAAAA: adLPA pGGfh Do0dS dDU-E7mdm p2r7Q sqkpF Tw706 6hmZX g0O0Q MjfUN i7XgW uVjUq 4KzH8 wEB. Accessed 8 Apr 2023
- 24. Jaffery SHI, Younas M, Khan M, Ali L (2020) Energy consump- tion analysis in turning Ti-6Al-4V alloy. In: 2020 IEEE 11th Inter- national Conference on Mechanical and Intelligent Manufacturing Technologies (ICMIMT). IEEE, pp 18-21
- 29. Khan M, Warsi SS, Jaffery SH, Ahmad R, Younas M (2019) Anal- ysis of energy consumption in orthogonal machining of Al 6061- T6 alloy. In: Advances in Manufacturing Technology XXXIII: Proceedings of the 17th International Conference on Manufac- turing Research, incorporating the 34th National Conference on Manufacturing Research, 10-12 September 2019. Queen's Uni- versity, Belfast, vol 9. IOS Press, p 327
- 30. Khan MA, Jaffery SHI, Khan M (2023) Assessment of sustain- ability of machining Ti-6Al-4V under cryogenic condition using energy map approach. Eng Sci Technol Int J 41:101357 https:// www. scien cedir ect. com/ scien ce/ artic le/ pii/ S2215 09862 30003 44
- 32. Khan MA, Jaffery SHI, Khan M, Younas M, Butt SI, Ahmad R et al (2020) Multi-objective optimization of turning titanium- based alloy Ti-6Al-4V under dry, wet, and cryogenic conditions using gray relational analysis (GRA). Int J Adv Manuf Technol 106:3897-911 · DOI
- 40. Groover MP (2020) Fundamentals of modern manufacturing: materials, processes, and systems. John Wiley & Sons 41. Astakhov VP, Shvets S. (2004) The assessment of plastic defor- mation in metal cutting. J Mater Process Technol [Internet] [cited 2023 Apr 25];146:193-202. Available from: https:// linki nghub. elsev ier. com/ retri eve/ pii/ S0924 01360 30099 81
- Astakhov VP, Shvets S. (2004) The assessment of plastic deformation in metal cutting. J Mater Process Technol [Internet] [cited 2023 Apr 25];146:193–202. Available from: https://linkinghub.elsevier.com/retrieve/pii/S0924013603009981 · DOI · Paper page
- 41. 2008) Machining dynamics: theory, applications and practices, London: Springer
Cited by
Ali, A., Younas, M., Khan, M., Jaffery, S. H. I., & Khan, Z. (2025) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-024-01147-9 · Cited by 31
Self-citation
Metadata
- Authors
- Younas, M., Khan, M., Jaffery, S. H. I., Khan, Z., & Khan, N.
- Affiliations
- Robert Gordon University (GB)
- Prince Mohammad bin Fahd University (SA)
- National University of Sciences and Technology (PK)
- HITEC University (PK)
- Riphah International University (PK)
- Corresponding author
- Younas, Muhammad
- Khan, Mushtaq
- Jaffery, Syed Husain Imran
- Khan, Zarak
- Khan, Nawar
- Venue
- The International Journal of Advanced Manufacturing Technology
- Published
- 2024-04-16
- Volume
- 132
- Issue
- 7-8
- Pages
- 3785-3799
- ISSN
- 0268-3768 (ISSN-L)
- 1433-3015
- OpenAlex
- W4394856314
- Cited by
- 17
- References
- 29
- Citations by year
- 2026: 9 · 2025: 6 · 2024: 2
- FWCI
- 2.28
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- The International Journal of Advanced Manufacturing Technology (publishedVersion, cc-by)
- Greenwich Academic Literature Archive (University of Greenwich) (submittedVersion)
- Open Access Institutional Repository at Robert Gordon University (Robert Gordon University) (submittedVersion, cc-by)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Materials Science › Metals and Alloys › Metal Alloys Wear and Properties
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
- Keywords
- Ti-6Al-4V, titanium alloy machining, tool wear, specific cutting energy, dry machining, uncoated carbide tools, tool-workpiece interaction, adhesion, material transfer, cutting speed, feed rate, energy consumption
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.