The DOI matches its Crossref record.
An assessment of petrol fire risk by oxygen consumption calorimetry
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The comparison of Figure 2 with the results of the scientific paper of Martinka et al. [21] shows that methanol and ethanol had a lower maximum heat release rate than automotive gasoline, but the course of the heat release rate was similar.”
From Impact of Water Content on Energy Potential and Combustion Characteristics of Methanol and Ethanol Fuels (2019) · cites this paper as [21]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
No references could be resolved yet.
Research works printed but not linked: 47
- Planas-Cuchi E, Casal J. Flame temperature distribution in a pool fire. J Hazard Mater. 1998;62:231–41. · doi:10.1016/s0304-3894(98)00177-0
- Planas-Cuchi E, Casal J. Modeling temperature evolution in equipment engulfed in a pool-fire. Fire Saf J. 1998;30:251–68. · doi:10.1016/s0379-7112(98)00053-8
- Chatris JM, Quintela J, Folch J, Planas E, Arnaldos J, Casal J. Experimental study of burning rate in hydrocarbon pool fire. Combust Flame. 2001;126:1373–83. · doi:10.1016/s0010-2180(01)00262-0
- Munoz M, Arnaldos J, Casal J, Planas E. Analysis of the geometric and radiative characteristics of hydrocarbon pool fires. Combust Flame. 2004;139:263–77. · doi:10.1016/j.combustflame.2004.09.001
- Najafi A, Moghaddam AZ. Modeling flame temperature profile on a fire-engulfed cylindrical tube. Fire Mater. 2012;36:565–74. · doi:10.1002/fam.1115
- Babrauskas V. Ignition handbook. Issaquah: Fire Science Publishers; 2003.
- Martinka J, Hroncová E, Chrebet T, Balog K. A comparison of the behaviour of spruce wood and polyolefins during the test on the cone calorimeter. Adv Mater Res. 2013;726:4280–7. · doi:10.4028/www.scientific.net/amr.726-731.4280
- Thornton W. The relation of oxygen to the heat of combustion of organic compounds. Philos Mag. 1917;33:196–203. · DOI · Paper page
- Huggett C. Estimation of the rate of heat release by means of oxygen consumption. Fire Mater. 1980;4:61–5. · DOI · Paper page
- Martinka J, Chrebet T, Hrušovský I, Balog K. Assessment of the impact of heat flux density on the combustion efficiency and fire hazard of spruce pellets. Eur J Environ Saf Sci. 2013;1:24–31.
- Hebda M, Laska M, Szechynska-Hebda M. Application of a device used for observation of controlled thermal processes in a furnace. J Therm Anal Calorim. 2013;114:1099–109. · DOI
- Ladomerský J, Hroncová E, Samešová D. Investigation of appropriate conditions for wood wastes combustion on basis of emission. Drew. 2003;46:90–8.
- Tewarson A, Jiang FH, Morikawa T. Ventilation-controlled combustion of polymers. Combust Flame. 1993;95:151–69. · doi:10.1016/0010-2180(93)90058-b
- Majlingová A, Oravec M, Šolc M, Galla Š. Modification of procedure to initiate the solids according to EN 60695-2-10 for materials used in historic buildings. Eur J Environ Saf Sci. 2013;1:8–12.
- Roh JS, Yang SS, Ryou HS, Yoon MO, Jeong YT. An experimental study on the effect of ventilation velocity on burning rate in tunnels fires-heptane pool fire case. Build Environ. 2008;43:1225–31. · doi:10.1016/j.buildenv.2007.03.007
- Brohez S, Marlair G, Delvosalle C. The effect of oxygen concentration on CO and soot yields in fires. Fire Mater. 2008;32:141–58. · doi:10.1002/fam.960
- Martinka J, Kačíková D, Hroncová E, Ladomerský J. Experimental determination of the effect of temperature and oxygen concentration on the production of birch wood main fire emissions. J Therm Anal Calorim. 2012;110:193–8. · doi:10.1007/s10973-012-2261-2
- Wang Q, Jia C, Jiang C, Wang Y, Wu D. Pyrolysis model of oil sand using thermogravimetric analysis. J Therm Anal Calorim. 2013;. doi: 10.1007/s10973-013-3505-5 . · doi:10.1007/s10973-013-3505-5
- Galla Š, Ivanovičová M. Assessment of fire risk of selected agglomerated wooden materials. Res J Recent Sci. 2013;2:43–7.
- Hu L, Wu L, Liu S. Flame length elongation behavior of medium hydrocarbon pool fires in cross air flow. Fuel. 2013;111:613–20. · doi:10.1016/j.fuel.2013.03.025
- Tao C, He Y, Li Y, Wang X. Effect of oblique air flow on burning rates of square ethanol pool fires. J Hazard Mater. 2013;260:552–62. · doi:10.1016/j.jhazmat.2013.06.015
- Chi JH. Using thermal analysis experiment and fire dynamics simulator (FDS) to reconstruct an arson fire scene. J Therm Anal Calorim. 2013;113:641–8. · doi:10.1007/s10973-012-2764-x
- Xu Q, Majlingová A, Zachar M, Jin C, Jiang Y. Correlation analysis of cone calorimetry test data assessment of the procedure with test of different polymers. J Therm Anal Calorim. 2012;110:65–70. · doi:10.1007/s10973-011-2059-7
- Dowdy S, Weardon S, Chilko D. Statistics for research. 3rd ed. New Jersey: Wiley; 2005.
- Pools Babrauskas V. In: Babrauskas V, Grayson SJ, editors. Heat release in fires. London: Interscience Communications; 2009. p. 201–6.
- Zabetakis MG, Burgess DS. Research on hazards associated with the production and handling of liquid hydrogen. Washington: Bureau of Mines; 1961.
- Karlsson B, Quintiere JG. Enclosure fire dynamics. London: CRC Press; 2000.
- Gottuk DT, White DA. Liquid fuel fires. In: DiNenno PJ, editor. SFPE handbook of fire protection engineering. 4th ed. Quincy: National Fire Protection Association; 2002. p. 297–316.
- Mealy C, Benfer M, Gottuk D. Liquid fuel spill fire dynamics. Fire Technol. 2012;. doi: 10.1007/s10694-012-0281-x . · doi:10.1007/s10694-012-0281-x
- Hu L, Tang F, Wang Q, Qiu Z. Burning characteristics of conduction-controlled rectangular hydrocarbon pool fires in a reduced pressure atmosphere at high altitude in Tibet. Fuel. 2013;111:298–304. · doi:10.1016/j.fuel.2013.04.032
- Yin J, Yao W, Liu Q, Wu N, Zhou Z, Wu Y, Zhang H. Experimental study of n-heptane pool fire behaviors under dynamic pressures in an altitude chamber. Procedia Eng. 2013;52:548–56. · doi:10.1016/j.proeng.2013.02.184
- Zhang Y, Ji J, Li J, Sun J, Wang Q, Huang Q. Effects of altitude and sample width on the characteristics of horizontal flame spread over wood sheets. Fire Saf J. 2012;51:120–5. · doi:10.1016/j.firesaf.2012.02.006
- Fang J, Tu R, Guan J, Wang J, Zhang Y. Influence of low air pressure on combustion characteristic and flame pulsation frequency of pool fires. Fuel. 2011;90:2760–6. · doi:10.1016/j.fuel.2011.03.035
- Yin J, Yao W, Liu Q, Zhou Z, Wu N, Zhang H, Lin C, Wu T, Meier OC. Experimental study of n-heptane pool fire behaviour in an altitude chamber. Int J Heat Mass Transf. 2013;62:543–52. · doi:10.1016/j.ijheatmasstransfer.2013.02.072
- Carvel R, Steinhaus T, Rein G, Torero JL. Determination of the flammability properties of polymeric materials: a novel method. Polym Degrad Stab. 2011;96:314–9. · doi:10.1016/j.polymdegradstab.2010.08.010
- Xu Q, Zachar M, Majlingová A, Jin C, Jiang Y. Evaluation of plywood fire behaviour by ISO tests. Eur J Environ Saf Sci. 2013;1:1–7.
- Parker WJ. Prediction of the heat release rate from basic measurements. In: Babrauskas V, Grayson SJ, editors. Heat release in fires. London: Interscience Communications; 2009. p. 333–56.
- Tran HC. Experimental data on wood materials. In: Babrauskas V, Grayson SJ, editors. Heat release in fires. London: Interscience Communications; 2009. p. 358–72.
- Hirschler MM. Heat release from plastic materials. In: Babrauskas V, Grayson SJ, editors. Heat release in fires. London: Interscience Communications; 2009. p. 375–422.
- Luche J, Mathis E, Rogaume T, Richard F, Guillaume E. High-density polyethylene thermal degradation and gaseous compound evolution in a cone calorimeter. Fire Saf J. 2012;54:24–35. · DOI · Paper page
- Zachar M, Mitterová I, Xu Q, Majlingová A, Cong J, Galla Š. Determination of fire and burning properties of spruce wood. Drv Ind. 2012;63:217–23. · DOI
- Makovická-Osvaldová L, Osvald A, Kačíková L. Coniferous wood reaction on fire in forest condition. Am Int J Contemp Res. 2012;2:37–46.
- Alfredsen G, Bader TK, Dibdiakova J, Filbakk T, Bollmus S, Hofstetter K. Thermogravimetric analysis for wood decay characterization. Eur J Wood Prod. 2012;70:527–30. · DOI
- Chrebet T, Martinka J, Balog K, Hrušovský I. Moment of lingocellulosic materials ignition defined by critical mass flow rate. Appl Mech Mater. 2013;291:1985–8. · doi:10.4028/www.scientific.net/amm.291-294.1985
- Ladomerský J. Emission analysis and minimization from the wood waste combustion. Wood Res. 2000;45:33–44.
- Tewarson A. Generation of heat and chemical compounds in fires. In: DiNenno PJ, editor. SFPE handbook of fire protection engineering. 4th ed. Quincy: National Fire Protection Association; 2002. p. 82–161.
- Chow WK, Han SS. Estimation of heat release rate for gasoline pool fires. Int J Eng Perform Based Fire Codes. 2007;9:59–64.
Cited by
Martinka, J., Rantuch, P., & Wachter, I. (2019) · Energies · doi:10.3390/en12183491 · Cited by 29
Self-citation
Metadata
- Authors
- Martinka, J., Chrebet, T., & Balog, K.
- Venue
- Journal of Thermal Analysis and Calorimetry
- Published
- 2014-03-18
- Volume
- 117
- Issue
- 1
- Pages
- 325-332
- ISSN
- 1388-6150
- 1588-2926
- Cited by
- 19
- References
- 0
- Language
- en
- Licence
- www.springer.com/tdm (tdm)
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: An assessment of petrol fire risk by oxygen consumption calorimetry. https://app.cochat.ai/papers/10.1007/s10973-014-3686-6
- The paper
- Martinka, J., Chrebet, T., & Balog, K. (2014). An assessment of petrol fire risk by oxygen consumption calorimetry. Journal of Thermal Analysis and Calorimetry. https://doi.org/10.1007/s10973-014-3686-6
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.