The DOI matches its Crossref record; 19 of the 19 references it cites were found in a registry or an index.
The Effectiveness of Hot Isostatic Pressing for Closing Porosity in Titanium Parts Manufactured by Selective Electron Beam Melting
Open accessAbstract
Ti-6Al-4V parts, produced by selective electron beam melting additive manufacturing, have been studied by X-ray computed tomography (XCT) to track pore closure during a standard hot isostatic pressing (HIPing) cycle. Comparison of repeated XCT scans before and after HIPing, on worst-case samples with different geometries, confirmed that all internal porosity was shrunk to below the resolution limit of the equipment used (~5 µm) following the HIPing cycle, apart from defects with surface connected ligaments.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A Threshold Selection Method from Gray-Level Histograms
Otsu, N. (1979) · IEEE Transactions on Systems, Man, and Cybernetics · doi:10.1109/tsmc.1979.4310076 · Cited by 43,398
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Suresh, S. (1998) · Cambridge University Press eBooks · doi:10.1017/cbo9780511806575 · Cited by 4,526
Maire, E., & Withers, P. J. (2014) · International Materials Reviews · doi:10.1179/1743280413y.0000000023 · Cited by 1,374
Self-citationPeterson's Stress Concentration Factors
Pilkey, W. D. (1997) · Wiley eBooks · doi:10.1002/9780470172674 · Cited by 885
Fundamental aspects of hot isostatic pressing: An overview
Atkinson, H. V., & Davies, S. (2000) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-000-0078-2 · Cited by 784
Peterson's Stress Concentration Factors
Pilkey, W. D., & Pilkey, D. F. (2007) · Wiley eBooks · doi:10.1002/9780470211106 · Cited by 716
Tammas-Williams, S., Zhao, H., Léonard, F., Derguti, F., Todd, I., & Prangnell, P. B. (2015) · Materials Characterization · doi:10.1016/j.matchar.2015.02.008 · Cited by 590
Self-citationRecent advances in X-ray microtomography applied to materials
Stock, S. R. (2008) · International Materials Reviews · doi:10.1179/174328008x277803 · Cited by 517
Electron Beam Additive Manufacturing of Titanium Components: Properties and Performance
Edwards, P., O'Conner, A., & Ramulu, M. (2013) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4025773 · Cited by 450
Cited by
Sanaei, N., & Fatemi, A. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100724 · Cited by 1,029
Metal additive manufacturing in the commercial aviation industry: A review
Gisario, A., Kazarian, M., Martina, F., & Mehrpouya, M. (2019) · Journal of Manufacturing Systems · doi:10.1016/j.jmsy.2019.08.005 · Cited by 574
The Influence of Porosity on Fatigue Crack Initiation in Additively Manufactured Titanium Components
Tammas-Williams, S., Withers, P. J., Todd, I., & Prangnell, P. B. (2017) · Scientific Reports · doi:10.1038/s41598-017-06504-5 · Cited by 494
Self-citationBiomedical Applications of Titanium Alloys: A Comprehensive Review
Marin, E., & Lanzutti, A. (2023) · Materials · doi:10.3390/ma17010114 · Cited by 489
Mechanical performance of additively manufactured meta-biomaterials
Zadpoor, A. A. (2019) · Acta Biomaterialia · doi:10.1016/j.actbio.2018.12.038 · Cited by 429
Metadata
- Authors
- Tammas-Williams, S., Withers, P. J., Todd, I., & Prangnell, P. B.
- Venue
- Metallurgical and Materials Transactions A
- Published
- 2016-03-16
- Volume
- 47
- Issue
- 5
- Pages
- 1939-1946
- ISSN
- 1073-5623 (ISSN-L)
- 1543-1940
- OpenAlex
- W2301483496
- Cited by
- 269
- References
- 19
- FWCI
- 24.20
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The Effectiveness of Hot Isostatic Pressing for Closing Porosity in Titanium Parts Manufactured by Selective Electron Beam Melting. https://app.cochat.ai/papers/10.1007/s11661-016-3429-3
- The paper
- Tammas-Williams, S., Withers, P. J., Todd, I., & Prangnell, P. B. (2016). The Effectiveness of Hot Isostatic Pressing for Closing Porosity in Titanium Parts Manufactured by Selective Electron Beam Melting. Metallurgical and Materials Transactions A. https://doi.org/10.1007/s11661-016-3429-3
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.