The DOI matches its Crossref record; 20 of the 20 references it cites were found in a registry or an index.
CFD Simulations of Feeder Tube Pressure Oscillations and Prediction of Clogging in Cold Spray Nozzles
Open accessOverview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“But these studies only considered the influence of the airflow on particles, and ignored the influence of the particles on each other.”
From Cold Spray Process for Co-Deposition of Copper and Aluminum Particles (2023) · cites this paper as [19]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Leal, L. G. (1979) · International Journal of Multiphase Flow · doi:10.1016/0301-9322(79)90021-1 · Cited by 5,300
Modeling of swirl in turbulent flow systems
Sloan, D. G., Smith, P. J., & Smoot, L. D. (1986) · Progress in Energy and Combustion Science · doi:10.1016/0360-1285(86)90016-x · Cited by 5,246
Development of a generalized parameter window for cold spray deposition
Schmidt, T., Gärtner, F., Assadi, H., & Kreye, H. (2006) · Acta Materialia · doi:10.1016/j.actamat.2005.10.005 · Cited by 1,183
The Cold Spray Materials Deposition Process: Fundamentals and Applications
(2007) · CRC Press eBooks · doi:10.1201/9781439824122 · Cited by 488
Binder, K., Gottschalk, J., Kollenda, M., Gärtner, F., & Klassen, T. (2010) · Journal of Thermal Spray Technology · doi:10.1007/s11666-010-9557-1 · Cited by 182
Gas Flow, Particle Acceleration, and Heat Transfer in Cold Spray: A review
Yin, S., Meyer, M., Li, W., Liao, H., & Lupoi, R. (2016) · Journal of Thermal Spray Technology · doi:10.1007/s11666-016-0406-8 · Cited by 181
Fukumoto, M., Wada, H., Tanabe, K., Yamada, M., Yamaguchi, E., Niwa, A., Sugimoto, M., & Izawa, M. (2007) · Journal of Thermal Spray Technology · doi:10.1007/s11666-007-9121-9 · Cited by 147
Vreman, B., Geurts, B. J., Deen, N. G., Kuipers, J. A. M., & Kuerten, J. G. M. (2008) · Flow Turbulence and Combustion · doi:10.1007/s10494-008-9173-z · Cited by 123
Theoretical and Experimental Particle Velocity in Cold Spray
Champagne, V. K., Helfritch, D. J., Dinavahi, S. P. G., & Leyman, P. (2010) · Journal of Thermal Spray Technology · doi:10.1007/s11666-010-9530-z · Cited by 122
Self-citationPowder stream characteristics in cold spray nozzles
Lupoi, R., & O’Neill, W. (2011) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2011.07.061 · Cited by 110
Cited by
Cold Spray Process for Co-Deposition of Copper and Aluminum Particles
Hu, S., Li, H., Zhang, L., & Xu, Y. (2023) · Coatings · doi:10.3390/coatings13111953 · Cited by 3
Metadata
- Authors
- Liebersbach, P., Foelsche, A., Champagne, V. K., Siopis, M., Nardi, A., & Schmidt, D. P.
- Affiliations
- University of Massachusetts Amherst (US)
- DEVCOM Army Research Laboratory (US)
- Corresponding author
- Liebersbach, Piotr
- Venue
- Journal of Thermal Spray Technology
- Published
- 2020-02
- Volume
- 29
- Issue
- 3
- Pages
- 400-412
- ISSN
- 1059-9630 (ISSN-L)
- 1544-1016
- OpenAlex
- W3006405206
- Cited by
- 30
- References
- 20
- Citations by year
- 2026: 1 · 2025: 6 · 2024: 6 · 2023: 3 · 2022: 8 · 2021: 3 · 2020: 3
- FWCI
- 2.55
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- www.springer.com/tdm (tdm)
- www.springer.com/tdm (vor)
- Locations
- Journal of Thermal Spray Technology (publishedVersion)
- Funders
- Massachusetts Green High Performance Computing Center
- Army Research Laboratory (W911NF-15–2-0024, W911NF, 2-0024, W911NF-15)
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Engineering › Mechanical Engineering › Additive Manufacturing Materials and Processes
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Particle Dynamics in Fluid Flows
- Keywords
- cold spray, nozzle clogging, particle-laden flow, two-phase flow, additive manufacturing, gas velocity
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
