Wet surface heat transfer and pressure drop of aluminum parallel flow heat exchangers at different inclination angles
Integrity signals
Registry
Cites
Statistics
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
For 1.5 mm and 2.0 mm fin pitch heat exchangers, the influence of inclination angles on the heat transfer coefficient can be ignored.
“For the 1.5 mm and 2.0 mm fin pitch heat exchangers, the influence of inclination angles on the heat transfer coefficient could be ignored.”
For 1.25 mm fin pitch heat exchangers, forward inclination can slightly increase the heat transfer coefficient.
“However, for 1.25 mm fin pitch heat exchangers, the forward inclination could slightly increase the heat transfer coefficient.”
Smaller fin pitch may increase fin bridging, while inclination angle may improve heat exchanger drain performance.
“Smaller fin pitch may increase fin bridging, while inclination angle may improve heat exchanger drain performance.”
Cites
Heat transfer and pressure drop characteristics of flat tube and louvered plate fin surfaces
Achaichia, A., & Cowell, T. A. (1988) · Experimental Thermal and Fluid Science · doi:10.1016/0894-1777(88)90032-5 · Cited by 235 · see citing works
Kim, M.-H., Song, S., & Bullard, C. W. (2002) · International Journal of Refrigeration · doi:10.1016/s0140-7007(01)00061-5 · Cited by 39 · see citing works
Flagged first, then by citations
Cited by
Sorted by citations
Xiong, T., Liu, G., Gao, Q., Yan, G., & Yu, J. (2023) · Journal of Building Engineering · doi:10.1016/j.jobe.2022.105654 · Cited by 26 · see citing works
Park, J.-S., Kim, J., & Lee, K.-S. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.01.043 · Cited by 24 · see citing works
- Authors
- Kim, N.-H., Kim, D.-Y., & Hwang, J.-H.
- Affiliations
- Incheon National University (KR)
- LG (South Korea) (KR)
- Corresponding author
- Kim, Nae-Hyun
- ORCID
- Kim, Do-Young
- Venue
- Journal of Mechanical Science and Technology
- Published
- 2008-12
- Volume
- 22
- Issue
- 12
- Pages
- 2498-2508
- ISSN
- 1738-494X (ISSN-L)
- 1976-3824
- OpenAlex
- W1977292783
- Cited by
- 10
- References
- 2
- Citations by year
- 2025: 2 · 2022: 2 · 2021: 3 · 2018: 1 · 2017: 1
- FWCI
- 0.71
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.springer.com/tdm (tdm)
- Locations
- Journal of Mechanical Science and Technology (publishedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Heat Transfer and Optimization
- Physical Sciences › Engineering › Mechanical Engineering › Heat Transfer and Boiling Studies
- Physical Sciences › Engineering › Mechanical Engineering › Heat Transfer Mechanisms
- Keywords
- pressure drop, aluminum heat exchangers, parallel flow heat exchanger, inclination angle, fin spacing, heat transfer coefficient, friction factor, condensate drainage
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
