The DOI matches its Crossref record; 60 of the 60 references it cites were found in a registry or an index; 6 of the 41 sources its claims cite were checked for support.
Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy
Open accessAbstract
This paper presents the machinability performance of uncoated, single-coated, and multicoated carbide tools during turning of Grade 5 (Ti6Al4V) Titanium alloy, which is challenging to machine due to its distinctive material properties. Coated tools with single-coated Titanium Aluminium Nitride (TiAlN) and multi-coated layer of Titanium Aluminium Nitride with Aluminium Chromium Nitride (TiAlN + AlCrN) coated inserts were utilized to assess surface roughness (Ra), tool wear rate (R), and chip morphologies under various cutting conditions using dry machining. Analysis of the used tools revealed that coated tools exhibited improved tool life and surface quality compared to uncoated tools across all cutting conditions. Multi-coated tools of TiAlN + AlCrN demonstrated a tool life increase of up to 15% compared to uncoated and single-coated tools, with surface roughness improvements ranging from 30 to 45% depending on cutting speed. Chip morphology analysis indicated an increase in the chip reduction coefficient with higher cutting speeds for all tool types. Coated tools exhibited the lowest chip-reduction coefficient due to the presence of TiAlN and AlCrN coatings, which control the tool chip contact length. Conversely, uncoated chip morphology resulted in larger chip thickness values compared to coated tools, particularly at cutting speeds above 100 m/min, attributed to poor heat dissipation and chemical reactions at the tool chip interface. Energy dispersive X-ray scanning electron microscopy (SEM/EDXS) analysis of worn uncoated inserts revealed a higher tendency towards Titanium adhesion compared to coated tools. The proposed multi-layer coatings of (TiAlN + AlCrN) used for dry machining proved highly beneficial for achieving economic machining objectives and may reduce the need for lubrication when processing Ti6Al4V alloys.
Overview
CoChat Summary
TL;DR
This study compares uncoated, TiAlN single-coated, and TiAlN + AlCrN multicoated H13 carbide inserts during dry turning of Ti6Al4V across 50–150 m/min. Multicoated tools gave the best surface finish and lowest wear/chip compression, with reported surface-roughness improvements up to 47% and wear reduction up to 12% (the abstract also reports up to 15% tool-life increase).
Key findings
- Surface roughness improved with cutting speed for all tools; multicoated inserts performed best. Uncoated Ra ranged from 2.84 to 1.45 µm, and multicoated tools achieved up to 1 µm at higher speed. Table 5 reports at 150 m/min: Ra 1.45 µm uncoated, 1.10 µm single-coated, 1.00 µm multicoated (31–45% improvement); at 50 m/min: 2.84, 1.79, and 1.5 µm (up to 47% improvement).
- Multicoated tools reduced wear rate compared with uncoated and single-coated tools. At 150 m/min, wear rate R was −5.25 (uncoated), −5.61 (single-coated), and −5.87 (multicoated), a 7–12% improvement; at 50 m/min, R was −6.01, −6.07, and −6.68, up to 11% improvement. The abstract reports tool-life increase up to 15%, while the conclusions report wear reduction up to 12%.
- Chip thickness and chip compression ratio increased with cutting speed for all tool types; coated tools had the lowest chip compression ratio due to TiAlN and AlCrN controlling tool-chip contact length. At 150 m/min, chip thickness was 0.275 mm (uncoated), 0.260 mm (single-coated), and 0.245 mm (multicoated); chip compression ratio r′ was 1.721, 1.622, and 1.529, respectively. Uncoated chips were thicker above 100 m/min.
- SEM/EDXS showed titanium adhesion on the uncoated flank face was five times higher than on multicoated tools; aluminum increased on the multicoated surface, believed to form a hard aluminum oxide layer, while vanadium showed the least transfer.
Methods
- Dry turning of Ti6Al4V Grade 5 (105 HRB) on a YIDA CNC machine using H13 carbide inserts (CCMW09T304H13) with 1.5 µm coating: uncoated, single TiAlN, and multicoated TiAlN + AlCrN.
- A total of 27 experiments: 9 cutting speeds (50, 55, 60, 62.5, 65, 70, 100, 130, 150 m/min) × 3 tool types, with constant feed 0.16 mm/rev, depth of cut 1 mm, and cut length 100 mm; a fresh insert was used for each test.
- Surface roughness measured with a portable roughness meter (three readings averaged per run); tool wear measured by optical microscope per ISO 3685 (VBmax under 0.6 mm) and used to calculate wear rate R; chip morphology analyzed by optical microscopy and geometric equations; worn inserts examined by SEM/EDXS.
Limitations
- The paper states no limitations.
- Evident from the text: improvement figures are inconsistent — the abstract reports up to 15% tool-life increase and 30–45% surface-roughness improvement, while the conclusions/Table 5 report up to 12% wear reduction and up to 47% surface-roughness improvement. BUE observations also conflict: Section 7 says more BUE on single/multicoated inserts, while Section 8 and the conclusions say more BUE on uncoated inserts.
- Evident from the methods: only one feed rate (0.16 mm/rev) and depth of cut (1 mm) were tested under dry conditions with a single workpiece material, so the findings are limited to those conditions.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures

























Verification
Claims the paper makes
5 Valid · 2 Not valid · 21 Not checked · 65 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The trend is increasing because of the linear proportionality of chip thickness and segmented ratio respectively, with respect to cutting speeds as also reported elsewhere [33, 36].”
What the sources say
- Not checked — no full text of the sourcecites [33] Maity, K., & Pradhan, S. (2017). Study of Chip Morphology, Flank Wear on Different Machinability Conditions of Titanium Alloy (Ti-6Al-4V) Using Response Surface Methodology Approach. International Journal of Materials Forming and Machining Processes (IJMFMP), 4(1), 19–37. source
- Partly supportedcites [36] Sánchez Hernández, Y., et al. (2018). Experimental parametric relationships for chip geometry in dry machining of the Ti6Al4V alloy. Materials, 11(7), 1260. sourceExperimental — accuracy not yet measured
Section 3.2 reports that peak height and equivalent chip thickness increase with cutting speed at low feed rates, and that the segment ratio tends to increase with cutting speed in that range. It attributes the almost linear increase and direct proportionality of chip thickness to feed rate, not cutting speed; it does not establish the claimed linear relationships or causal explanation for the speed trend. (LLM, conf=0.87)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Titanium based alloy form shear deformed chips even at lower speeds, as a result the conventional trend of decreasing chip thickness with increasing speed, which is well known for conventional alloys, is not the case for titanium based alloys.”
What the sources say
- Partly supportedcites [36] Sánchez Hernández, Y., et al. (2018). Experimental parametric relationships for chip geometry in dry machining of the Ti6Al4V alloy. Materials, 11(7), 1260. sourceExperimental — accuracy not yet measured
In Results and Discussion §3.2 (page unavailable), the paper reports that chip peak height increased with cutting speed at a feed rate of 0.10 mm/r, and that equivalent chip thickness followed the same trend. At higher feed rates, however, peak height was greatest at the lowest speed tested. The finding therefore supports an exception to the decreasing-thickness trend for Ti6Al4V under some conditions, not the claim’s categorical statement about titanium-based alloys. (LLM, conf=0.87)
boosted- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“As the cutting angle and the radius of the cutting edge is increased, the chip compression ratio increases [13, 36].”
What the sources say
- Not checked — no full text of the sourcecites [13] Grzesik, W. (2008). Advanced machining processes of metallic materials: theory, modelling and applications. Elsevier. source
- Could not verifycites [36] Sánchez Hernández, Y., et al. (2018). Experimental parametric relationships for chip geometry in dry machining of the Ti6Al4V alloy. Materials, 11(7), 1260. sourceExperimental — accuracy not yet measured
The Materials and Methods section describes tests using the same tool geometry while varying cutting speed and feed rate. Section 3.2 reports chip shrinkage but does not test whether increasing the cutting angle or cutting-edge radius increases the chip compression ratio. Searches for those angle- and radius-dependent effects found no supporting passage in our copy; no page numbers were provided. (LLM, conf=0.76)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
Every source the paper cites for this claim was checked and supports it.
In the paper
“Titanium based alloy form shear deformed chips even at lower speeds, as a result the conventional trend of decreasing chip thickness with increasing speed, which is well known for conventional alloys, is not the case for titanium based alloys.”
What the sources say
- Supportedcites [36] Sánchez Hernández, Y., et al. (2018). Experimental parametric relationships for chip geometry in dry machining of the Ti6Al4V alloy. Materials, 11(7), 1260. source
The Introduction (page not specified) says Ti6Al4V generates segmented chips at relatively low cutting speeds. It also describes adiabatic shear-band formation as an explanation for segmentation, and the Results (section 3.1; page not specified) observe deformation along those bands. This supports the quoted point about shear-deformed chips at lower speeds. (LLM, conf=0.89)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“It was observed that surface roughness is improved by increasing the cutting speed for all types of tool coatings.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
62 more claims
Create a free account to see all 93 claims and to verify the 5 references still open.
- Probably not a substantial claim. 11
- It may state two separate claims as one. 19
- Borderline: one of the tests for a substantial claim is unclear. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ 7 Chip Morphology Analysis
“It was observed that more buildup edge (BUE) were produced at the cutting nose of single and multi-coated inserts as compared to uncoated inserts. This results in high tool wear and surface roughness in single and multi-coated inserts.”
§ 8 Tool Wear Analysis
“During the experimentation and optical microscopy of the coated and uncoated inserts, it was observed that more BUE were produced at the cutting edge/ zone of uncoated inserts as compared to single and multi-coated inserts.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 1 Introduction
“The comparison of yield strength of different materials with Ti6Al4V alloy is shown in Table1, that shows higher yield strength of Ti6Al4V alloy comparative to other material at all temperatures.”
§ 1 Introduction
“| Ti6Al4V | 6.7 | 526.3 | 1100 | | WC-Co (6-10%) | 60-80 | 200-400 | 1440 |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Abstract
“Multi-coated tools of TiAlN + AlCrN demonstrated a tool life increase of up to 15% compared to uncoated and single-coated tools, with surface roughness improvements ranging from 30 to 45% depending on cutting speed.”
§ 9 Conclusions
“For multi-coated inserts, the surface roughness improved up to 47% owing to the better thermal conductivity at lower affinity of BUE on the tool coating.”
Citations
Cites
Titanium alloys and their machinability—a review
Ezugwu, E. O., & Wang, Z. M. (1997) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(96)00030-1 · Cited by 1,702
Journal of Achievements in Materials and Manufacturing Engineering
(2017) · Journal of Achievements of Materials and Manufacturing Engineering · doi:10.5604/17348412 · Cited by 978
Key improvements in the machining of difficult-to-cut aerospace superalloys
Ezugwu, E. O. (2005) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.02.003 · Cited by 945 · cited 1×
“This trend has been attributed in the past to strain hardening and localized thermal softening as well as low thermal conductivity of titanium based alloys [22, 29, 45].”
Environmental friendly cutting fluids and cooling techniques in machining: a review
Debnath, S., Reddy, M. M., & Yi, Q. S. (2014) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2014.07.071 · Cited by 812
Dry machining: Machining of the future
Sreejith, P. S., & Ngoi, B. K. A. (2000) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(00)00445-3 · Cited by 684
Calamaz, M., Coupard, D., & Girot, F. (2008) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2007.10.014 · Cited by 622
Recent advances of superhard nanocomposite coatings: a review
Zhang, S., Sun, D., Fu, Y., & Du, H. (2003) · Surface and Coatings Technology · doi:10.1016/s0257-8972(02)00903-9 · Cited by 492
The cutting process, chips, and cutting forces in machining CFRP
Koplev, A., Lystrup, A., & Vorm, T. (1983) · Composites · doi:10.1016/0010-4361(83)90157-x · Cited by 405
New observations on the mechanism of chip formation when machining titanium alloys
Komanduri, R., & Von Turkovich, B. F. (1981) · Wear · doi:10.1016/0043-1648(81)90242-8 · Cited by 405 · cited 1×
“It has been reported extensively by past researchers including Komanduri et al. [43], Astakhov et al. [44] and others [34] reported that chip formation in the case for machining of Titanium based alloys follows a different trend as compared to the conventional metals.”
Friction and wear properties of TiN, TiAlN, AlTiN and CrAlN PVD nitride coatings
Aihua, L., Jianxin, D., Haibing, C., Yangyang, C., & Jun, Z. (2012) · International Journal of Refractory Metals and Hard Materials · doi:10.1016/j.ijrmhm.2011.09.010 · Cited by 371
Cited by
Afridi, S. A., Younas, M., Khan, Z., & Khan, A. M. (2025) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-024-01203-4 · Cited by 28
Self-citationWang, G., Chen, X., Xu, Z., Feng, F., Zhang, J., Zhang, X., & Feng, P. (2025) · Technologies · doi:10.3390/technologies13050172 · Cited by 20
Superlubricity for Sustainable Technology: A Review
Liu, Y., Le, K., Bae, S.-M., Song, W., Hwang, Y., Xu, S., & Kim, D. E. (2025) · International Journal of Precision Engineering and Manufacturing-Green Technology · doi:10.1007/s40684-025-00774-5 · Cited by 6
Tognazzo, M., Sorgato, M., Bertolini, R., Ghiotti, A., & Bruschi, S. (2025) · Wear · doi:10.1016/j.wear.2025.206421 · Cited by 6
de Souza, A. F., SOUZA, L. L. D., GAUDENCIO, J. H. D., da Silva, C. E. S., Verri, F. A. N., & Balestrassi, P. P. (2026) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-025-06078-8 · Cited by 9
Time-Based Study of Tool Wear in Dry Turning of Ti-6Al-4 V with Coated and Bare WC–Co Tools
Dixit, U., Guduru, R. K., & Rashid, A. (2026) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-025-12484-9
Performance Analysis of Coated and UnCoated Tools in Turning Ti-6Al-4V ELI
Engineering, J. N. U. D. O. M. S., Kim, H.-J., Oh, S.-H., & So, B. M. (2026) · Journal of the Korean Society of Manufacturing Process Engineers · doi:10.14775/ksmpe.2026.25.4.029
Tao, L., Chen, J., 蔡飞, Xu, D., & Zhang, S. (2026) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2026.148551
Sarma, D., Ozah, R., Chandrasekaran, M., & Sahoo, A. K. (2026) · Australian Journal of Mechanical Engineering · doi:10.1080/14484846.2026.2649693
Abdullah, H. M., Ausaf, M. F., & Hasan, S. (2026) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-026-18443-5
Metadata
- Authors
- Ali, A., Younas, M., Khan, M., Jaffery, S. H. I., & Khan, Z.
- Affiliations
- National University of Sciences and Technology (PK)
- Robert Gordon University (GB)
- Prince Mohammad bin Fahd University (SA)
- University of Greenwich (GB)
- Corresponding author
- Ali, Ahsen
- Younas, Muhammad
- Khan, Mushtaq
- Jaffery, Syed Husain Imran
- Khan, Zarak
- Venue
- International Journal of Precision Engineering and Manufacturing
- Published
- 2024-10-22
- Volume
- 26
- Issue
- 1
- Pages
- 43-58
- ISSN
- 1229-8557 (ISSN-L)
- 2234-7593
- 2005-4602
- OpenAlex
- W4403636767
- Cited by
- 31
- References
- 57
- Citations by year
- 2026: 20 · 2025: 11
- FWCI
- 4.16
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- International Journal of Precision Engineering and Manufacturing (publishedVersion, cc-by)
- Greenwich Academic Literature Archive (University of Greenwich) (acceptedVersion)
- Open Access Institutional Repository at Robert Gordon University (Robert Gordon University) (submittedVersion, cc-by)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
- Keywords
- Ti-6Al-4V, titanium alloy turning, coated carbide tools, multilayer coatings, TiAlN, tool life, surface roughness, chip morphology, chip reduction coefficient, dry machining, cutting speed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.