The DOI matches its Crossref record; 22 of the 22 references it cites were found in a registry or an index.
A new material model for 2D numerical simulation of serrated chip formation when machining titanium alloy Ti–6Al–4V
Open accessAbstract
Abstract A new material constitutive law is implemented in a 2D finite element model to analyse the chip formation and shear localisation when machining titanium alloys. The numerical simulations use a commercial finite element software (FORGE 2005®) able to solve complex thermo-mechanical problems. One of the main machining characteristics of titanium alloys is to produce segmented chips for a wide range of cutting speeds and feeds. The present study assumes that the chip segmentation is only induced by adiabatic shear banding, without material failure in the primary shear zone. The new developed model takes into account the influence of strain, strain rate and temperature on the flow stress and also introduces a strain softening effect. The tool chip friction is managed by a combined Coulomb–Tresca friction law. The influence of two different strain softening levels and machining parameters on the cutting forces and chip morphology has been studied. Chip morphology, cutting and feed forces predicted by numerical simulations are compared with experimental results.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Modelling and simulation of high‐speed machining
Marusich, T. D., & Ortíz, M. (1995) · International Journal for Numerical Methods in Engineering · doi:10.1002/nme.1620382108 · Cited by 523
The influence of friction models on finite element simulations of machining
Özel, T. (2005) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.07.001 · Cited by 407
New observations on the mechanism of chip formation when machining titanium alloys
Komanduri, R., & Von Turkovich, B. F. (1981) · Wear · doi:10.1016/0043-1648(81)90242-8 · Cited by 405
Finite element simulation of conventional and high speed machining of Ti6Al4V alloy
Umbrello, D. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2007.05.007 · Cited by 383
A finite element analysis of orthogonal machining using different tool edge geometries
Yen, Y.-C., Jain, A., & Altan, T. (2003) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(03)00846-x · Cited by 352
Mechanics of Saw-Tooth Chip Formation in Metal Cutting
Vyas, A., & Shaw, M. C. (1999) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.2831200 · Cited by 301
Prediction of chip morphology and segmentation during the machining of titanium alloys
Hua, J., & Shivpuri, R. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2004.01.028 · Cited by 247
Modeling the high strain rate behavior of titanium undergoing ballistic impact and penetration
Meyer, H. W., & Kleponis, D. S. (2001) · International Journal of Impact Engineering · doi:10.1016/s0734-743x(01)00107-5 · Cited by 226
Friction modelling in metal cutting
Childs, T. H. C. (2006) · Wear · doi:10.1016/j.wear.2005.01.052 · Cited by 217
A finite element model of high speed metal cutting with adiabatic shearing
Bäker, M., Rösler, J., & Siemers, C. (2002) · Computers & Structures · doi:10.1016/s0045-7949(02)00023-8 · Cited by 189
Research works printed but not linked: 13
- E.J.A. Armarego, Predictive modelling of machining operations—a means of bridging the gap between the theory and practice—a keynote paper, in: The 13th Symposium on Engineering Applications of Mechanics, CMSE, Hamilton, Ontario, Canada, 7–9 May 1996.
- Bayoumi, 1995, Some metallurgical aspects of chip formation in cutting Ti–6wt.%Al–4wt.%V alloy, Materials Science and Engineering A, 190, 173, 10.1016/0921-5093(94)09595-N · doi:10.1016/0921-5093(94)09595-n
- Guo, 2006, Dynamic material behavior modelling using internal state variable plasticity and its application in hard machining simulations, Journal of Manufacturing Science and Engineering, 128, 749, 10.1115/1.2193549 · doi:10.1115/1.2193549
- L. Li, N. He, A FEA study on mechanisms of saw-tooth chip deformation in high speed cutting of Ti–6–Al–4V alloy, in: Fifth International Conference on High Speed Machining (HSM), Metz, France, 14–16 March 2006, pp. 759–767.
- P.J. Arrazola, D. Ugarte, J.A. Villar, S. Marya, Finite element modelling: a qualitative tool to study high speed machining, in: Fifth International Conference on High Speed Machining (HSM), Metz, France, 14–16 March 2006, pp. 239–246.
- Barge, 2005, Numerical modelling of orthogonal cutting: influence of numerical parameters, Journal of Materials Processing Technology, 164,165, 1148, 10.1016/j.jmatprotec.2005.02.118 · doi:10.1016/j.jmatprotec.2005.02.118
- Pantalé, 2004, 2D and 3D numerical models of metal cutting with damage effects, Computer Methods in Applied Mechanics and Engineering, 193, 4383, 10.1016/j.cma.2003.12.062 · doi:10.1016/j.cma.2003.12.062
- Kassner, 2002, Large-strain softening of aluminium in shear at elevated temperature, Metallurgical and Materials Transactions A, 33A, 3145, 10.1007/s11661-002-0300-5 · doi:10.1007/s11661-002-0300-5
- Ding, 2004, Miscrostructural evolution of a Ti–6Al–4V alloy during β-phase processing: experimental and simulative investigations, Materials Science and Engineering A, 365, 172, 10.1016/j.msea.2003.09.024 · doi:10.1016/j.msea.2003.09.024
- V. Kalhori, Doctoral Thesis, Institutionen for Maskinteknik, Lulea Tekniska Universitet, 2001.
- Filice, 2007, A critical analysis on the friction modelling in orthogonal machining, International Journal of Machine Tools and Manufacture, 47, 709, 10.1016/j.ijmachtools.2006.05.007 · doi:10.1016/j.ijmachtools.2006.05.007
- M. Calamaz, D. Coupard, M. Nouari, F. Girot, A finite element model of high speed machining of TA6V titanium alloy, in: Sixth International Conference on High Speed Machining (HSM), San Sebastian, Spain, 21–22 March 2007 (edited CD).
- Lee, 1998, Plastic deformation and fracture behavior of Ti–6Al–4V alloy, Materials Science and Engineering A, 241, 48, 10.1016/S0921-5093(97)00471-1 · doi:10.1016/s0921-5093(97)00471-1
Cited by
Machining induced surface integrity in titanium and nickel alloys: A review
Ulutan, D., & Ozel, T. (2011) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2010.11.003 · Cited by 1,252
Sima, M., & Özel, T. (2010) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2010.08.004 · Cited by 477
Shear localization in metallic materials at high strain rates
Yan, N., Li, Z., Xu, Y., & Meyers, M. A. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100755 · Cited by 296
Advances in material and friction data for modelling of metal machining
Melkote, S. N., Grzesik, W., Outeiro, J., Rech, J., Schulze, V., Attia, H., Arrazola, P.-J., M’Saoubi, R., & Saldana, C. (2017) · CIRP Annals · doi:10.1016/j.cirp.2017.05.002 · Cited by 284
Karpat, Y. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.12.008 · Cited by 150
Metadata
- Authors
- Calamaz, M., Coupard, D., & Girot, F.
- Venue
- International Journal of Machine Tools and Manufacture
- Publisher
- Elsevier BV
- Published
- 2008-03
- Volume
- 48
- Issue
- 3-4
- Pages
- 275-288
- ISSN
- 0890-6955 (ISSN-L)
- OpenAlex
- W2079503926
- Cited by
- 622
- References
- 22
- FWCI
- 19.18
- Type
- journal article
- Language
- en
- Open access
- green
- Licence
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: A new material model for 2D numerical simulation of serrated chip formation when machining titanium alloy Ti–6Al–4V. https://app.cochat.ai/papers/10.1016/j.ijmachtools.2007.10.014
- The paper
- Calamaz, M., Coupard, D., & Girot, F. (2008). A new material model for 2D numerical simulation of serrated chip formation when machining titanium alloy Ti–6Al–4V. International Journal of Machine Tools and Manufacture. https://doi.org/10.1016/j.ijmachtools.2007.10.014
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.