The DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index.
Microstructure, defects and mechanical behavior of beta-type titanium porous structures manufactured by electron beam melting and selective laser melting
Open accessAbstract
Abstract This study investigates the differences in the microstructure, defects and mechanical behavior of porous structures from a β-type Ti 24Nb 4Zr 8Sn manufactured by electron beam melting (EBM) and selective laser melting (SLM). The phases, size and shape of melt pool, volume and distribution of defects are analyzed and correlated to the compressive mechanical and fatigue properties. Due to different powder bed temperatures, the microstructure of EBM and SLM samples consists of α+β phases and a single β phase, respectively. The faster cooling rate during SLM promotes the formation of fine β dendrites, which leads to a higher compressive strength (50 ± 0.9 MPa) and lower Young's Modulus (0.95 ± 0.05 GPa) in comparison to the EBM parts (45 ± 1.1 MPa and 1.34 ± 0.04 GPa respectively). The large defects present within solid strut are likely a result of tin vaporization. The tin vapor is more easily trapped during the SLM process due to a smaller laser spot size and a faster cooling rate. This results in a 10 times increase in the number of defects. These defects have a limited influence on both the static properties and low stresses level fatigue strength, but it causes a reduced and variable fatigue life at high stresses level.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Ti based biomaterials, the ultimate choice for orthopaedic implants – A review
Geetha, M., Singh, A. K., Asokamani, R., & Gogia, A. K. (2009) · Progress in Materials Science · doi:10.1016/j.pmatsci.2008.06.004 · Cited by 5,416
Titanium alloys in total joint replacement—a materials science perspective
Long, M., & Rack, H. J. (1998) · Biomaterials · doi:10.1016/s0142-9612(97)00146-4 · Cited by 3,510
Ultrahigh Strength and High Electrical Conductivity in Copper
Lu, L., Shen, Y., Chen, X., Qian, L., & Lu, K. (2004) · Science · doi:10.1126/science.1092905 · Cited by 3,366
Selective laser melting of iron-based powder
Kruth, J. P., Froyen, L., Van Vaerenbergh, J., Mercelis, P., Rombouts, M., & Lauwers, B. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2003.11.051 · Cited by 1,550
Effects of defects, inclusions and inhomogeneities on fatigue strength
MURAKAMI, Y., & Endo, M. (1994) · International Journal of Fatigue · doi:10.1016/0142-1123(94)90001-9 · Cited by 1,102
Qiu, C., Panwisawas, C., Ward, R., Basoalto, H., Brooks, J. W., & Attallah, M. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.06.004 · Cited by 1,041
Gong, H., Rafi, K., Gu, H., Janaki Ram, G. D., Starr, T., & Stucker, B. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.07.147 · Cited by 940
A review of rapid prototyping techniques for tissue engineering purposes
Peltola, S. M., Melchels, F. P. W., Grijpma, D. W., & Kellomäki, M. (2008) · Annals of Medicine · doi:10.1080/07853890701881788 · Cited by 751
Manufacture by selective laser melting and mechanical behavior of commercially pure titanium
Attar, H., Calin, M., Zhang, L. C., Scudino, S., & Eckert, J. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.11.038 · Cited by 744
Self-citationZhang, L., & Attar, H. (2016) · Advanced Engineering Materials · doi:10.1002/adem.201500419 · Cited by 721
Self-citation
Cited by
A Review on Biomedical Titanium Alloys: Recent Progress and Prospect
Zhang, L., & Chen, L. (2019) · Advanced Engineering Materials · doi:10.1002/adem.201801215 · Cited by 1,100
Self-citationChowdhury, S., Yadaiah, N., Prakash, C., Ramakrishna, S., Dixit, S., Gupta, L. R., & Buddhi, D. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.07.121 · Cited by 784
Mechanistic models for additive manufacturing of metallic components
Wei, H. L., Mukherjee, T., Zhang, W., Zuback, J. S., Knapp, G. L., De, A., & DebRoy, T. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100703 · Cited by 530
Additive Manufacturing of Titanium Alloys by Electron Beam Melting: A Review
Zhang, L., Liu, Y., Li, S., & Hao, Y. (2018) · Advanced Engineering Materials · doi:10.1002/adem.201700842 · Cited by 486
Self-citationWang, J., Zhu, R., Liu, Y., & Zhang, L. (2023) · Advanced Powder Materials · doi:10.1016/j.apmate.2023.100137 · Cited by 484
Self-citation
Metadata
- Authors
- Liu, Y. J., Li, S. J., Wang, H. L., Hou, W. T., Hao, Y. L., Yang, R., Sercombe, T. B., & Zhang, L. C.
- Venue
- Acta Materialia
- Publisher
- Elsevier BV
- Published
- 2016-07
- Volume
- 113
- Pages
- 56-67
- ISSN
- 1359-6454 (ISSN-L)
- OpenAlex
- W2382359737
- Cited by
- 584
- References
- 34
- FWCI
- 57.84
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Microstructure, defects and mechanical behavior of beta-type titanium porous structures manufactured by electron beam melting and selective laser melting. https://app.cochat.ai/papers/10.1016/j.actamat.2016.04.029
- The paper
- Liu, Y. J., Li, S. J., Wang, H. L., Hou, W. T., Hao, Y. L., Yang, R., Sercombe, T. B., & Zhang, L. C. (2016). Microstructure, defects and mechanical behavior of beta-type titanium porous structures manufactured by electron beam melting and selective laser melting. Acta Materialia. https://doi.org/10.1016/j.actamat.2016.04.029
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.