The DOI matches its Crossref record; 39 of the 39 references it cites were found in a registry or an index.
Microstructure evolution and critical stress for twinning in the CrMnFeCoNi high-entropy alloy
Open accessAbstract
At low homologous temperatures (down to cryogenic temperatures), the CrMnFeCoNi high-entropy alloy possesses good combination of strength, work hardening rate (WHR), ductility, and fracture toughness. To improve understanding of the deformation mechanisms responsible for its mechanical properties, tensile tests were performed at liquid nitrogen and room temperature (77 K and 293 K) and interrupted at different strains to quantify the evolution of microstructure by transmission electron microscopy. Dislocation densities, and twin widths, their spacings, and volume fractions were determined. Nanotwins were first observed after true strains of ∼7.4% at 77 K and ∼25% at 293 K; at lower strains, deformation occurs by dislocation plasticity. The tensile stress at which twinning occurs is 720 ± 30 MPa, roughly independent of temperature, from which we deduce a critical resolved shear stress for twinning of 235 ± 10 MPa. In the regime where deformation occurs by dislocation plasticity, the shear modulus normalized WHR decreases with increasing strain at both 77 K and 293 K. Beyond ∼7.4% true strain, the WHR at 77 K remains constant at a high value of G/30 because twinning is activated, which progressively introduces new interfaces in the microstructure. In contrast, the WHR at room temperature continues to decrease with increasing strain because twinning is not activated until much later (close to fracture). Thus, the enhanced strength-ductility combination at 77 K compared to 293 K is primarily due to twinning starting earlier in the deformation process and providing additional work hardening. Consistent with this, when tensile specimens were pre-strained at 77 K to introduce nanotwins, and subsequently tested at 293 K, flow stress and ductility both increased compared to specimens that were not pre-strained.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Microstructural development in equiatomic multicomponent alloys
Cantor, B., Chang, I. T. H., Knight, P., & Vincent, A. J. B. (2004) · Materials Science and Engineering: A · doi:10.1016/j.msea.2003.10.257 · Cited by 10,130
A fracture-resistant high-entropy alloy for cryogenic applications
Gludovatz, B., Hohenwarter, A., Catoor, D., Chang, E. H., George, E. P., & Ritchie, R. O. (2014) · Science · doi:10.1126/science.1254581 · Cited by 5,714
Self-citationMechanical properties of nanocrystalline materials
Meyers, M. A., Mishra, A., & Benson, D. J. (2006) · Progress in Materials Science · doi:10.1016/j.pmatsci.2005.08.003 · Cited by 4,597
Transmission Electron Microscopy
Williams, D. B., & Carter, C. B. (2009) · Springer eBooks · doi:10.1007/978-0-387-76501-3 · Cited by 3,963
Christian, J. W., & Mahajan, S. (1995) · Progress in Materials Science · doi:10.1016/0079-6425(94)00007-7 · Cited by 3,603
Otto, F., Dlouhý, A., Somsen, C., Bei, H., Eggeler, G., & George, E. P. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.06.018 · Cited by 3,352
Self-citationKinetics of flow and strain-hardening
Mecking, H., & Kocks, U. F. (1981) · Acta Metallurgica · doi:10.1016/0001-6160(81)90112-7 · Cited by 2,814
Sluggish diffusion in Co–Cr–Fe–Mn–Ni high-entropy alloys
Tsai, K.-Y., Tsai, M.-H., & Yeh, J.-W. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.04.058 · Cited by 2,366
The onset of twinning in metals: a constitutive description
Meyers, M. A., Vöhringer, O., & Lubarda, V. A. (2001) · Acta Materialia · doi:10.1016/s1359-6454(01)00300-7 · Cited by 1,695
Relative effects of enthalpy and entropy on the phase stability of equiatomic high-entropy alloys
Otto, F., Yang, Y., Bei, H., & George, E. P. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.01.042 · Cited by 1,445
Self-citationSchuh, B., Mendez-Martin, F., Völker, B., George, E. P., Clemens, H., Pippan, R., & Hohenwarter, A. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.06.025 · Cited by 1,323
Self-citationTensile properties of high- and medium-entropy alloys
Gali, A., & George, E. P. (2013) · Intermetallics · doi:10.1016/j.intermet.2013.03.018 · Cited by 1,194
Self-citationHigh-entropy alloys: a critical assessment of their founding principles and future prospects
Pickering, E. J., & Jones, N. G. (2016) · International Materials Reviews · doi:10.1080/09506608.2016.1180020 · Cited by 1,062
Otto, F., Dlouhý, A., Pradeep, K. G., Kuběnová, M., Raabe, D., Eggeler, G., & George, E. P. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.04.005 · Cited by 932
Self-citationGrain growth and the Hall–Petch relationship in a high-entropy FeCrNiCoMn alloy
Liu, W. H., Wu, Y., He, J. Y., Nieh, T. G., & Lu, Z. P. (2013) · Scripta Materialia · doi:10.1016/j.scriptamat.2012.12.002 · Cited by 916
Mechanical Properties and Stacking Fault Energies of NiFeCrCoMn High-Entropy Alloy
Zaddach, A. J., Niu, C., Koch, C. C., & Irving, D. L. (2013) · JOM · doi:10.1007/s11837-013-0771-4 · Cited by 878
Nanoscale origins of the damage tolerance of the high-entropy alloy CrMnFeCoNi
Zhang, Z., Mao, M. M., Wang, J., Gludovatz, B., Zhang, Z., Mao, S. X., George, E. P., Yu, Q., & Ritchie, R. O. (2015) · Nature Communications · doi:10.1038/ncomms10143 · Cited by 845
Self-citation(1932) · Nature · doi:10.1038/129717b0 · Cited by 830
Salishchev, G. A., Tikhonovsky, M. A., Shaysultanov, D. G., Stepanov, N. D., Kuznetsov, A. V., Kolodiy, I. V., Tortika, A. S., & Senkov, O. N. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2013.12.210 · Cited by 702
Temperature dependent stacking fault energy of FeCrCoNiMn high entropy alloy
Huang, S., Li, W., Lu, S., Tian, F., Shen, J., Holmström, E., & Vitos, L. (2015) · Scripta Materialia · doi:10.1016/j.scriptamat.2015.05.041 · Cited by 583
The determination of foil thickness by scanning transmission electron microscopy
Kelly, P., Jostsons, A., Blake, R. G., & Napier, J. G. (1975) · physica status solidi (a) · doi:10.1002/pssa.2210310251 · Cited by 576
Precipitation in the equiatomic high-entropy alloy CrMnFeCoNi
Pickering, E. J., Muñoz-Moreno, R., Stone, H. J., & Jones, N. G. (2016) · Scripta Materialia · doi:10.1016/j.scriptamat.2015.10.025 · Cited by 555
Steinmetz, D., Jäpel, T., Wietbrock, B., Eisenlohr, P., Gutiérrez‐Urrutia, I., Saeed‐Akbari, A., Hickel, T., Roters, F., & Raabe, D. (2012) · Acta Materialia · doi:10.1016/j.actamat.2012.09.064 · Cited by 550
Microstructure and texture evolution during annealing of equiatomic CoCrFeMnNi high-entropy alloy
Bhattacharjee, P. P., Sathiaraj, G. D., Zaid, M., Gatti, J. R., Lee, C., Tsai, C.-W., & Yeh, J.-W. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2013.10.237 · Cited by 530
The determination of dislocation densities in thin films
Ham, R. K. (1961) · Philosophical magazine · doi:10.1080/14786436108239679 · Cited by 518
Laplanche, G., Gadaud, P., Horst, O., Otto, F., Eggeler, G., & George, E. P. (2015) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2014.11.061 · Cited by 467
Self-citationEffect of cryo-deformation on structure and properties of CoCrFeNiMn high-entropy alloy
Stepanov, N., Tikhonovsky, M., Yurchenko, N., Zyabkin, D., Klimova, M., Zherebtsov, S., Efimov, A., & Salishchev, G. (2015) · Intermetallics · doi:10.1016/j.intermet.2014.12.004 · Cited by 399
Insights into the phase diagram of the CrMnFeCoNi high entropy alloy
Laurent-Brocq, M., Akhatova, A., Perrière, L., Chebini, S., Sauvage, X., Leroy, E., & Champion, Y. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.01.068 · Cited by 361
Nano-twin mediated plasticity in carbon-containing FeNiCoCrMn high entropy alloys
Wu, Z., Parish, C. M., & Bei, H. (2015) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2015.05.224 · Cited by 358
Steady state flow of the FeCoNiCrMn high entropy alloy at elevated temperatures
He, J. Y., Zhu, C., Zhou, D. Q., Liu, W. H., Nieh, T. G., & Lu, Z. P. (2014) · Intermetallics · doi:10.1016/j.intermet.2014.06.015 · Cited by 358
Incipient plasticity and dislocation nucleation of FeCoCrNiMn high-entropy alloy
Zhu, C., Lu, Z. P., & Nieh, T. G. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.01.059 · Cited by 342
Otto, F., Hanold, N. L., & George, E. P. (2014) · Intermetallics · doi:10.1016/j.intermet.2014.05.014 · Cited by 322
Self-citationPhase stability of non-equiatomic CoCrFeMnNi high entropy alloys
Ma, D., Yao, M., Pradeep, K. G., Tasan, C. C., Springer, H., & Raabe, D. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.07.030 · Cited by 262
Processing, Microstructure and Mechanical Properties of the CrMnFeCoNi High-Entropy Alloy
Gludovatz, B., George, E. P., & Ritchie, R. O. (2015) · JOM · doi:10.1007/s11837-015-1589-z · Cited by 254
Self-citationAtomic-scale characterization and modeling of 60° dislocations in a high-entropy alloy
Smith, T. M., Hooshmand, M. S., Esser, B. D., Otto, F., McComb, D. W., George, E. P., Ghazisaeidi, M., & Mills, M. J. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.03.045 · Cited by 226
Self-citationMicrostructural evolution of a CoCrFeMnNi high-entropy alloy after swaging and annealing
Laplanche, G., Horst, O. M., Otto, F., Eggeler, G., & George, E. P. (2015) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2015.05.129 · Cited by 224
Self-citationPolycrystalline elastic moduli of a high-entropy alloy at cryogenic temperatures
Haglund, A., Koehler, M., Catoor, D., George, E. P., & Keppens, V. (2015) · Intermetallics · doi:10.1016/j.intermet.2014.11.005 · Cited by 196
Self-citationSlip nucleation in single crystal FeNiCoCrMn high entropy alloy
Patriarca, L., Ojha, A., Şehitoğlu, H., & Chumlyakov, Y. I. (2015) · Scripta Materialia · doi:10.1016/j.scriptamat.2015.09.009 · Cited by 155
A study of lattice elasticity from low entropy metals to medium and high entropy alloys
Huang, E., Yu, D., Yeh, J. W., Lee, C., An, K., & Tu, S.-Y. (2015) · Scripta Materialia · doi:10.1016/j.scriptamat.2015.01.011 · Cited by 59
Cited by
George, E. P., Raabe, D., & Ritchie, R. O. (2019) · Nature Reviews Materials · doi:10.1038/s41578-019-0121-4 · Cited by 5,047
Self-citationHigh entropy alloys: A focused review of mechanical properties and deformation mechanisms
George, E. P., Curtin, W. A., & Tasan, C. C. (2020) · Acta Materialia · doi:10.1016/j.actamat.2019.12.015 · Cited by 1,917
Self-citationMechanical behavior of high-entropy alloys
Li, W., Xie, D., Li, D., Zhang, Y., Gao, Y., & Liaw, P. K. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100777 · Cited by 1,321
Mechanical properties of high-entropy alloys with emphasis on face-centered cubic alloys
Li, Z., Zhao, S., Ritchie, R. O., & Meyers, M. A. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2018.12.003 · Cited by 1,171
Zhao, Y. L., Yang, T., Tong, Y., Wang, J., Luan, J. H., Jiao, Z. B., Chen, D., Yang, Y., Hu, A., Liu, C. T., et al. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.07.029 · Cited by 998
Metadata
- Authors
- Laplanche, G., Kostka, A., Horst, O. M., Eggeler, G., & George, E. P.
- Venue
- Acta Materialia
- Publisher
- Elsevier BV
- Published
- 2016-10
- Volume
- 118
- Pages
- 152-163
- ISSN
- 1359-6454 (ISSN-L)
- OpenAlex
- W2483357472
- Cited by
- 1,198
- References
- 39
- FWCI
- 68.47
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.