The DOI matches its Crossref record; 39 of the 39 references it cites were found in a registry or an index.
Microstructure evolution and critical stress for twinning in the CrMnFeCoNi high-entropy alloy
Open accessAbstract
At low homologous temperatures (down to cryogenic temperatures), the CrMnFeCoNi high-entropy alloy possesses good combination of strength, work hardening rate (WHR), ductility, and fracture toughness. To improve understanding of the deformation mechanisms responsible for its mechanical properties, tensile tests were performed at liquid nitrogen and room temperature (77 K and 293 K) and interrupted at different strains to quantify the evolution of microstructure by transmission electron microscopy. Dislocation densities, and twin widths, their spacings, and volume fractions were determined. Nanotwins were first observed after true strains of ∼7.4% at 77 K and ∼25% at 293 K; at lower strains, deformation occurs by dislocation plasticity. The tensile stress at which twinning occurs is 720 ± 30 MPa, roughly independent of temperature, from which we deduce a critical resolved shear stress for twinning of 235 ± 10 MPa. In the regime where deformation occurs by dislocation plasticity, the shear modulus normalized WHR decreases with increasing strain at both 77 K and 293 K. Beyond ∼7.4% true strain, the WHR at 77 K remains constant at a high value of G/30 because twinning is activated, which progressively introduces new interfaces in the microstructure. In contrast, the WHR at room temperature continues to decrease with increasing strain because twinning is not activated until much later (close to fracture). Thus, the enhanced strength-ductility combination at 77 K compared to 293 K is primarily due to twinning starting earlier in the deformation process and providing additional work hardening. Consistent with this, when tensile specimens were pre-strained at 77 K to introduce nanotwins, and subsequently tested at 293 K, flow stress and ductility both increased compared to specimens that were not pre-strained.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Microstructural development in equiatomic multicomponent alloys
Cantor, B., Chang, I. T. H., Knight, P., & Vincent, A. J. B. (2004) · Materials Science and Engineering: A · doi:10.1016/j.msea.2003.10.257 · Cited by 10,130
A fracture-resistant high-entropy alloy for cryogenic applications
Gludovatz, B., Hohenwarter, A., Catoor, D., Chang, E. H., George, E. P., & Ritchie, R. O. (2014) · Science · doi:10.1126/science.1254581 · Cited by 5,714
Self-citationMechanical properties of nanocrystalline materials
Meyers, M. A., Mishra, A., & Benson, D. J. (2006) · Progress in Materials Science · doi:10.1016/j.pmatsci.2005.08.003 · Cited by 4,597
Transmission Electron Microscopy
Williams, D. B., & Carter, C. B. (2009) · Springer eBooks · doi:10.1007/978-0-387-76501-3 · Cited by 3,963
Christian, J. W., & Mahajan, S. (1995) · Progress in Materials Science · doi:10.1016/0079-6425(94)00007-7 · Cited by 3,603
Otto, F., Dlouhý, A., Somsen, C., Bei, H., Eggeler, G., & George, E. P. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.06.018 · Cited by 3,352
Self-citationKinetics of flow and strain-hardening
Mecking, H., & Kocks, U. F. (1981) · Acta Metallurgica · doi:10.1016/0001-6160(81)90112-7 · Cited by 2,814
Sluggish diffusion in Co–Cr–Fe–Mn–Ni high-entropy alloys
Tsai, K.-Y., Tsai, M.-H., & Yeh, J.-W. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.04.058 · Cited by 2,366
The onset of twinning in metals: a constitutive description
Meyers, M. A., Vöhringer, O., & Lubarda, V. A. (2001) · Acta Materialia · doi:10.1016/s1359-6454(01)00300-7 · Cited by 1,695
Relative effects of enthalpy and entropy on the phase stability of equiatomic high-entropy alloys
Otto, F., Yang, Y., Bei, H., & George, E. P. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.01.042 · Cited by 1,445
Self-citation
Cited by
George, E. P., Raabe, D., & Ritchie, R. O. (2019) · Nature Reviews Materials · doi:10.1038/s41578-019-0121-4 · Cited by 5,047
Self-citationHigh entropy alloys: A focused review of mechanical properties and deformation mechanisms
George, E. P., Curtin, W. A., & Tasan, C. C. (2020) · Acta Materialia · doi:10.1016/j.actamat.2019.12.015 · Cited by 1,917
Self-citationMechanical behavior of high-entropy alloys
Li, W., Xie, D., Li, D., Zhang, Y., Gao, Y., & Liaw, P. K. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100777 · Cited by 1,321
Mechanical properties of high-entropy alloys with emphasis on face-centered cubic alloys
Li, Z., Zhao, S., Ritchie, R. O., & Meyers, M. A. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2018.12.003 · Cited by 1,171
Zhao, Y. L., Yang, T., Tong, Y., Wang, J., Luan, J. H., Jiao, Z. B., Chen, D., Yang, Y., Hu, A., Liu, C. T., et al. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.07.029 · Cited by 998
Gao, X., Lu, Y., Zhang, B., Liang, N., Wu, G., Sha, G., Liu, J., & Zhao, Y. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.07.041 · Cited by 887
Multicomponent high-entropy Cantor alloys
Cantor, B. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100754 · Cited by 877
Tunable stacking fault energies by tailoring local chemical order in CrCoNi medium-entropy alloys
Ding, J., Yu, Q., Asta, M., & Ritchie, R. O. (2018) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1808660115 · Cited by 845
Li, Q.-J., Sheng, H., & Ma, E. (2019) · Nature Communications · doi:10.1038/s41467-019-11464-7 · Cited by 795
Choi, W.-M., Jo, Y. H., Sohn, S. S., Lee, S., & Lee, B.-J. (2018) · npj Computational Materials · doi:10.1038/s41524-017-0060-9 · Cited by 794
Zhu, Z. G., Nguyen, Q. B., Ng, F. L., An, X. H., Liao, X. Z., Liaw, P. K., Nai, S. M. L., & Wei, J. (2018) · Scripta Materialia · doi:10.1016/j.scriptamat.2018.05.015 · Cited by 653
Wu, S. W., Wang, G., Wang, Q., Jia, Y. D., Yi, J., Zhai, Q. J., Liu, J. B., Sun, B. A., Chu, H. J., Shen, J., et al. (2019) · Acta Materialia · doi:10.1016/j.actamat.2018.12.012 · Cited by 640
Sun, Z., Tan, X., Tor, S. B., & Chua, C. K. (2018) · NPG Asia Materials · doi:10.1038/s41427-018-0018-5 · Cited by 627
Fan, L., Yang, T., Zhao, Y., Luan, J., Zhou, G., Wang, H., Jiao, Z., & Liu, C.-T. (2020) · Nature Communications · doi:10.1038/s41467-020-20109-z · Cited by 598
Exceptional fracture toughness of CrCoNi-based medium- and high-entropy alloys at 20 kelvin
Liu, D., Yu, Q., Kabra, S., Jiang, M., Forna-Kreutzer, P., Zhang, R., Payne, M., Walsh, F., Gludovatz, B., Asta, M., et al. (2022) · Science · doi:10.1126/science.abp8070 · Cited by 543
Self-citationThe evolution of the deformation substructure in a Ni-Co-Cr equiatomic solid solution alloy
Miao, J., Slone, C. E., Smith, T. M., Niu, C., Bei, H., Ghazisaeidi, M., Pharr, G. M., & Mills, M. J. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.04.033 · Cited by 539
High‐Entropy Alloys: Potential Candidates for High‐Temperature Applications – An Overview
Praveen, S., & Kim, H. S. (2018) · Advanced Engineering Materials · doi:10.1002/adem.201700645 · Cited by 526
Jo, Y. H., Jung, S., Choi, W. M., Sohn, S. S., Kim, H. S., Lee, B. J., Kim, N. J., & Lee, S. (2017) · Nature Communications · doi:10.1038/ncomms15719 · Cited by 470
Sun, S. J., Tian, Y. Z., Lin, H. R., Dong, X. G., Wang, Y. H., Zhang, Z. J., & Zhang, Z. F. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.07.054 · Cited by 469
Magnetically-driven phase transformation strengthening in high entropy alloys
Niu, C., LaRosa, C. R., Miao, J., Mills, M. J., & Ghazisaeidi, M. (2018) · Nature Communications · doi:10.1038/s41467-018-03846-0 · Cited by 393
Boron doped ultrastrong and ductile high-entropy alloys
Seol, J. B., Bae, J. W., Li, Z., Chan Han, J., Kim, J. G., Raabe, D., & Kim, H. S. (2018) · Acta Materialia · doi:10.1016/j.actamat.2018.04.004 · Cited by 375
An, X. H., Wu, S. D., Wang, Z. G., & Zhang, Z. F. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2018.11.001 · Cited by 374
Ming, K., Bi, X., & Wang, J. (2018) · International Journal of Plasticity · doi:10.1016/j.ijplas.2017.10.005 · Cited by 330
Cooperative deformation in high-entropy alloys at ultralow temperatures
Naeem, M., He, H., Zhang, F., Huang, H., Harjo, S., Kawasaki, T., Wang, B., Lan, S., Wu, Z., Wang, F., et al. (2020) · Science Advances · doi:10.1126/sciadv.aax4002 · Cited by 323
From high-entropy alloys to complex concentrated alloys
Gorsse, S., Couzinié, J.-P., & Miracle, D. B. (2018) · Comptes Rendus. Physique · doi:10.1016/j.crhy.2018.09.004 · Cited by 293
Zhang, T. W., Ma, S. G., Zhao, D., Wu, Y. C., Zhang, Y., Wang, Z. H., & Qiao, J. W. (2020) · International Journal of Plasticity · doi:10.1016/j.ijplas.2019.08.013 · Cited by 293
Park, J. M., Moon, J., Bae, J. W., Jang, M. J., Park, J., Lee, S., & Kim, H. S. (2018) · Materials Science and Engineering: A · doi:10.1016/j.msea.2018.02.031 · Cited by 290
Solid-solution strengthening in refractory high entropy alloys
Coury, F. G., Kaufman, M., & Clarke, A. J. (2019) · Acta Materialia · doi:10.1016/j.actamat.2019.06.006 · Cited by 290
Okamoto, N. L., Yuge, K., Tanaka, K., Inui, H., & George, E. P. (2016) · AIP Advances · doi:10.1063/1.4971371 · Cited by 274
Self-citationKinetically-controlled laser-synthesis of colloidal high-entropy alloy nanoparticles
Waag, F., Li, Y., Ziefuß, A. R., Bertin, E., Kamp, M., Duppel, V., Marzun, G., Kienle, L., Barcikowski, S., & Gökce, B. (2019) · RSC Advances · doi:10.1039/c9ra03254a · Cited by 273
Resistance of CoCrFeMnNi high-entropy alloy to gaseous hydrogen embrittlement
Zhao, Y., Lee, D.-H., Seok, M.-Y., Lee, J.-A., Phaniraj, M. P., Suh, J.-Y., Ha, H.-Y., Kim, J.-Y., Ramamurty, U., & Jang, J.-I. (2017) · Scripta Materialia · doi:10.1016/j.scriptamat.2017.03.029 · Cited by 267
Metadata
- Authors
- Laplanche, G., Kostka, A., Horst, O. M., Eggeler, G., & George, E. P.
- Venue
- Acta Materialia
- Publisher
- Elsevier BV
- Published
- 2016-10
- Volume
- 118
- Pages
- 152-163
- ISSN
- 1359-6454 (ISSN-L)
- OpenAlex
- W2483357472
- Cited by
- 1,198
- References
- 39
- FWCI
- 68.47
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.