The DOI matches its Crossref record; 41 of the 41 references it cites were found in a registry or an index.
Effect of heat treatment on the microstructural evolution of a nickel-based superalloy additive-manufactured by laser powder bed fusion
Open accessAbstract
Elemental segregation is a ubiquitous phenomenon in additive-manufactured (AM) parts due to solute rejection and redistribution during the solidification process. Using electron microscopy, in situ synchrotron X-ray scattering and diffraction, and thermodynamic modeling, we reveal that in an AM nickel-based superalloy, Inconel 625, stress-relief heat treatment leads to the growth of unwanted δ-phase precipitates on a time scale much faster than that in wrought alloys (minutes versus tens to hundreds of hours). The root cause for this behavior is the elemental segregation that results in local compositions of AM alloys outside the bounds of the allowable range set for wrought alloys. In situ small angle scattering experiments reveal that platelet-shaped δ phase precipitates grow continuously and preferentially along their lateral dimensions during stress-relief heat treatment, while the thickness dimension reaches a plateau very quickly. In situ XRD experiments reveal that nucleation and growth of δ-phase precipitates occur within 5 min during stress-relief heat treatment, indicating a low nucleation barrier and a short incubation time. An activation energy for the growth of δ phase was found to be (131.04 ± 0.69) kJ mol−1. We further demonstrate that a subsequent homogenization heat treatment can effectively homogenize the AM alloy and remove the deleterious δ phase. The combined experimental and modeling methodology in this work can be extended to elucidate the phase evolution during heat treatments in a broad range of AM materials.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
GSAS-II: the genesis of a modern open-source all purpose crystallography software package
Toby, B. H., & Von Dreele, R. B. (2013) · Journal of Applied Crystallography · doi:10.1107/s0021889813003531 · Cited by 6,195
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Thermo-Calc & DICTRA, computational tools for materials science
Andersson, J.-O., Helander, T., Höglund, L., Shi, P., & Sundman, B. (2002) · Calphad · doi:10.1016/s0364-5916(02)00037-8 · Cited by 4,322
Laser additive manufacturing of metallic components: materials, processes and mechanisms
Gu, D. D., Meiners, W., Wissenbach, K., & Poprawe, R. (2012) · International Materials Reviews · doi:10.1179/1743280411y.0000000014 · Cited by 3,197
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
The status, challenges, and future of additive manufacturing in engineering
Gao, W., Zhang, Y., Ramanujan, D., Ramani, K., Chen, Y., Williams, C. B., Wang, C. C. L., Shin, Y. C., Zhang, S., & Zavattieri, P. D. (2015) · Computer-Aided Design · doi:10.1016/j.cad.2015.04.001 · Cited by 2,631
The metallurgy and processing science of metal additive manufacturing
Sames, W. J., List, F. A., Pannala, S., Dehoff, R. R., & Babu, S. S. (2016) · International Materials Reviews · doi:10.1080/09506608.2015.1116649 · Cited by 2,529
Residual stresses in selective laser sintering and selective laser melting
Mercelis, P., & Kruth, J. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610707013 · Cited by 2,015
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.07.022 · Cited by 1,896
Metal Additive Manufacturing: A Review of Mechanical Properties
Lewandowski, J. J., & Seifi, M. (2016) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070115-032024 · Cited by 1,722
Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies
Murr, L. E., Gaytan, S. M., Ramirez, D. A., Martinez, E., Hernandez, J., Amato, K. N., Shindo, P. W., Medina, F. R., & Wicker, R. B. (2012) · Journal of Materials Science & Technology · doi:10.1016/s1005-0302(12)60016-4 · Cited by 1,686
Irena: tool suite for modeling and analysis of small-angle scattering
Ilavsky, J., & Jemian, P. R. (2009) · Journal of Applied Crystallography · doi:10.1107/s0021889809002222 · Cited by 1,612
Approximations Leading to a Unified Exponential/Power-Law Approach to Small-Angle Scattering
Beaucage, G. (1995) · Journal of Applied Crystallography · doi:10.1107/s0021889895005292 · Cited by 1,531
King, W. E., Anderson, A. T., Ferencz, R. M., Hodge, N. E., Kamath, C., Khairallah, S. A., & Rubenchik, A. M. (2015) · Applied Physics Reviews · doi:10.1063/1.4937809 · Cited by 1,258
Brandl, E., Heckenberger, U., Holzinger, V., & Buchbinder, D. (2012) · Materials & Design · doi:10.1016/j.matdes.2011.07.067 · Cited by 1,151
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Mower, T. M., & Long, M. J. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.068 · Cited by 1,001
Jia, Q., & Gu, D. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2013.09.171 · Cited by 905
Dinda, G. P., Dasgupta, A. K., & Mazumder, J. (2009) · Materials Science and Engineering: A · doi:10.1016/j.msea.2009.01.009 · Cited by 858
Zhang, D., Niu, W., Cao, X., & Liu, Z. (2015) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.06.021 · Cited by 723
Microstructural and texture development in direct laser fabricated IN718
Parimi, L. L., Ravi, G. A., Clark, D., & Attallah, M. M. (2014) · Materials Characterization · doi:10.1016/j.matchar.2013.12.012 · Cited by 565
Overview of Current Additive Manufacturing Technologies and Selected Applications
Horn, T. J., & Harrysson, O. L. A. (2012) · Science Progress · doi:10.3184/003685012x13420984463047 · Cited by 542
Denlinger, E. R., Heigel, J. C., Michaleris, P., & Palmer, T. A. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.07.030 · Cited by 531
Microstructure Characteristics of Inconel 625 Superalloy Manufactured by Selective Laser Melting
Li, S., Wei, Q., Shi, Y., Zhu, Z., & Zhang, D. (2015) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2014.09.020 · Cited by 526
Murr, L. E., Martinez, E., Amato, K. N., Gaytan, S. M., Hernandez, J., Ramirez, D. A., Shindo, P. W., Medina, F., & Wicker, R. B. (2012) · Journal of Materials Research and Technology · doi:10.1016/s2238-7854(12)70009-1 · Cited by 470
Kinetics of nucleation in near-critical fluids
Langer, J. S., & Schwartz, A. J. (1980) · Physical Review A · doi:10.1103/physreva.21.948 · Cited by 462
Keller, T., Lindwall, G., Ghosh, S., Ma, L., Lane, B. M., Zhang, F., Kattner, U. R., Lass, E. A., Heigel, J. C., Idell, Y., et al. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.05.003 · Cited by 457
Self-citationDie Keimbildung bei der Ausscheidung in metallischen Mischkristallen
Becker, R. (1938) · Annalen der Physik · doi:10.1002/andp.19384240115 · Cited by 380
Beaucage, G. B., & Schaefer, D. W. (1994) · Journal of Non-Crystalline Solids · doi:10.1016/0022-3093(94)90581-9 · Cited by 310
Ultra-small-angle X-ray scattering at the Advanced Photon Source
Ilavsky, J., Jemian, P. R., Allen, A. J., Zhang, F., Levine, L. E., & Long, G. G. (2009) · Journal of Applied Crystallography · doi:10.1107/s0021889809008802 · Cited by 295
Self-citationInvestigating laser rapid manufacturing for Inconel-625 components
Paul, C. P., Ganesh, P., Mishra, S. K., Bhargava, P., Negi, J., & Nath, A. K. (2007) · Optics & Laser Technology · doi:10.1016/j.optlastec.2006.01.008 · Cited by 274
Mostafa, A. O., Rubio, I. P., Braïlovski, V., Jahazi, M., & Medraj, M. (2017) · Metals · doi:10.3390/met7060196 · Cited by 247
High density selective laser melting of Waspaloy®
Mumtaz, K. A., Erasenthiran, P., & Hopkinson, N. (2008) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2007.04.117 · Cited by 245
Lass, E. A., Stoudt, M. R., Williams, M. E., Katz, M. B., Levine, L. E., Phan, T. Q., Gnaupel-Herold, T. H., & Ng, D. S. (2017) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-017-4304-6 · Cited by 228
Self-citationIlavsky, J., Zhang, F., Allen, A. J., Levine, L. E., Jemian, P. R., & Long, G. G. (2013) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-012-1431-y · Cited by 162
Self-citationOn the primary spacing and microsegregation of cellular dendrites in laser deposited Ni–Nb alloys
Ghosh, S., Ma, L., Ofori-Opoku, N., & Guyer, J. E. (2017) · Modelling and Simulation in Materials Science and Engineering · doi:10.1088/1361-651x/aa7369 · Cited by 153
Stoudt, M. R., Lass, E. A., Ng, D. S., Williams, M. E., Zhang, F., Campbell, C. E., Lindwall, G., & Levine, L. E. (2018) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-018-4643-y · Cited by 119
Self-citationCertification of Standard Reference Material 660B
Black, D. R., Windover, D., Henins, A., Filliben, J. J., & Cline, J. P. (2011) · Powder Diffraction · doi:10.1154/1.3591064 · Cited by 107
Modeling Precipitation Kinetics During Heat Treatment with Calphad-Based Tools
Chen, Q., Wu, K., Sterner, G., & Mason, P. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-1255-6 · Cited by 84
Zhang, F., Levine, L. E., Allen, A. J., Campbell, C. E., Creuziger, A. A., Kazantseva, N. V., & Ilavský, J. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.03.058 · Cited by 77
Self-citationAndrews, R. N., Serio, J., Muralidharan, G., & Ilavský, J. (2017) · Journal of Applied Crystallography · doi:10.1107/s1600576717006446 · Cited by 34
Cited by
Svetlizky, D., Das, M., Zheng, B., Vyatskikh, A. L., Bose, S., Bandyopadhyay, A., Schoenung, J. M., Lavernia, E. J., & Eliaz, N. (2021) · Materials Today · doi:10.1016/j.mattod.2021.03.020 · Cited by 1,371
Powder Bed Fusion of nickel-based superalloys: A review
Sanchez, S., Smith, P., Xu, Z., Gaspard, G., Hyde, C. J., Wits, W. W., Ashcroft, I. A., Chen, H., & Clare, A. T. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103729 · Cited by 541
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Mostafaei, A., Ghiaasiaan, R., Ho, I.-T., Strayer, S., Chang, K.-C., Shamsaei, N., Shao, S., Paul, S., Yeh, A.-C., Tin, S., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101108 · Cited by 531
Mechanistic models for additive manufacturing of metallic components
Wei, H. L., Mukherjee, T., Zhang, W., Zuback, J. S., Knapp, G. L., De, A., & DebRoy, T. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100703 · Cited by 530
Metadata
- Authors
- Zhang, F., Levine, L. E., Allen, A. J., Stoudt, M. R., Lindwall, G., Lass, E. A., Williams, M. E., Idell, Y., & Campbell, C. E.
- Venue
- Acta Materialia
- Publisher
- Elsevier BV
- Published
- 2018-06
- Volume
- 152
- Pages
- 200-214
- ISSN
- 1359-6454 (ISSN-L)
- OpenAlex
- W2795504960
- Cited by
- 291
- References
- 41
- FWCI
- 17.91
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.