The DOI matches its Crossref record; 10 of the 10 references it cites were found in a registry or an index.
The influence of Laves phases on the room temperature tensile properties of Inconel 718 fabricated by powder feeding laser additive manufacturing
Abstract
In this paper, a powder feeding laser additive manufacturing technology has been used for fabricating the Inconel 718 super-alloy. Laves phases of different sizes and morphologies have been obtained by using three types of heat treatments. The influence of Laves phases on the room temperature tensile properties of laser additive manufactured Inconel 718 has been investigated. The results show that small and granular Laves phase can be gained after heat treatment at 1050 °C for 15 min (S-15 sample). When the holding time extends to 45 min, the morphologies of Laves phases basically remain unchanged while its volume fraction further decreases (S-45 sample). Nevertheless, irregular and long-striped Laves phases still exist in the samples only after direct aging heat treatment (DA sample). The room temperature tensile results reveal that the S-15 samples have better tensile strength and ductility than that of S-45 samples. Besides, the DA samples with irregular and long-striped Laves phases show the lowest tensile strength and ductility. Hence, a certain amount of small and granular Laves phases are presumably beneficial for the room temperature tensile properties of Inconel 718. Moreover, a model has been established to describe the fracture of the Laves phase. On the basis of the fracture model, the critical stress needed for the fracture of long-striped Laves phases is lower than that needed for the fracture of granular Laves phases. Therefore, the former generally suffered internal fracture while the latter often fail by interfacial decohesion. Through influencing the volume fraction, the size and the distribution of γ" phase, the effect of the Laves phases on the room temperature tensile property is achieved. Furthermore, a yield strength model has been developed to reveal this influence in terms of numbers. The yield strength increments caused by grains, solution elements and γ′ phase are almost the same for the three kinds of samples. The differences of the yield strength are mainly caused by γ" phase. In addition, in terms of ductility, granular Laves phases are more favorable than long-striped Laves phases.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Mechanical Behavior of Materials
Meyers, M. A., & Chawla, K. K. (2008) · Cambridge University Press eBooks · doi:10.1017/cbo9780511810947 · Cited by 3,376
Microstructural and texture development in direct laser fabricated IN718
Parimi, L. L., Ravi, G. A., Clark, D., & Attallah, M. M. (2014) · Materials Characterization · doi:10.1016/j.matchar.2013.12.012 · Cited by 565
On the prediction of the yield stress of unimodal and multimodal γ ′ Nickel-base superalloys
Galindo-Nava, E. I., Connor, L. D., & Rae, C. M. F. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.07.048 · Cited by 428
Structural characterization of the aged Inconel 718
Slama, C., & Abdellaoui, M. (2000) · Journal of Alloys and Compounds · doi:10.1016/s0925-8388(00)00789-1 · Cited by 327
Effect of energy input on microstructural evolution of direct laser fabricated IN718 alloy
Ma, M., Wang, Z., & Zeng, X. (2015) · Materials Characterization · doi:10.1016/j.matchar.2015.06.027 · Cited by 187
On the microtwinning mechanism in a single crystal superalloy
Barba, D., Alabort, E., Pedrazzini, S., Collins, D. M., Wilkinson, A. J., Bagot, P. A. J., Moody, M. P., Atkinson, C., Jérusalem, A., & Reed, R. C. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.05.072 · Cited by 179
Schneider, J. A., Lund, B., & Fullen, M. D. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.03.005 · Cited by 171
Liu, F., Lin, X., Leng, H., Cao, J., Liu, Q., Huang, C., & Huang, W. (2012) · Optics & Laser Technology · doi:10.1016/j.optlastec.2012.06.028 · Cited by 125
Self-citationEffect of Cooling Rate on the Microstructure of Laser-Remelted INCONEL 718 Coating
Zhang, Y., Li, Z., Nie, P., & Wu, Y. (2013) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-013-1903-8 · Cited by 94
Self-citationSui, S., Zhong, C., Chen, J., Gasser, A., Huang, W., & Schleifenbaum, J. H. (2017) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2017.11.004 · Cited by 89
Self-citation
Cited by
Powder Bed Fusion of nickel-based superalloys: A review
Sanchez, S., Smith, P., Xu, Z., Gaspard, G., Hyde, C. J., Wits, W. W., Ashcroft, I. A., Chen, H., & Clare, A. T. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103729 · Cited by 541
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Mostafaei, A., Ghiaasiaan, R., Ho, I.-T., Strayer, S., Chang, K.-C., Shamsaei, N., Shao, S., Paul, S., Yeh, A.-C., Tin, S., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101108 · Cited by 531
Mechanistic models for additive manufacturing of metallic components
Wei, H. L., Mukherjee, T., Zhang, W., Zuback, J. S., Knapp, G. L., De, A., & DebRoy, T. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100703 · Cited by 530
Progress and perspectives in laser additive manufacturing of key aeroengine materials
Tan, C., Weng, F., Sui, S., Chew, Y., & Bi, G. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103804 · Cited by 520
Self-citation
Metadata
- Authors
- Sui, S., Tan, H., Chen, J., Zhong, C., Li, Z., Fan, W., Gasser, A., & Huang, W.
- Venue
- Acta Materialia
- Publisher
- Elsevier BV
- Published
- 2019-02
- Volume
- 164
- Pages
- 413-427
- ISSN
- 1359-6454 (ISSN-L)
- OpenAlex
- W2897423593
- Cited by
- 551
- References
- 10
- FWCI
- 17.11
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.