The DOI matches its Crossref record; 56 of the 56 references it cites were found in a registry or an index.
Topological design, permeability and mechanical behavior of additively manufactured functionally graded porous metallic biomaterials
Abstract
Recent advances in additive manufacturing (AM) have enabled the fabrication of functionally graded porous biomaterials (FGPBs) for application as orthopedic implants and bone substitutes. Here, we present a step-wise topological design of FGPB based on diamond unit cells to mimic the structure of the femoral diaphysis. The FGPB was manufactured from Ti-6Al-4V powder using the selective laser melting (SLM) technique. The morphological parameters, permeability and mechanical properties of FGPB samples were measured and compared with those of the biomaterials with uniform porous structures based on the same type of the unit cell. The FGPB exhibited a low density (1.9 g/cm3), a moderate Young's modulus (10.44 GPa), a high yield stress (170.6 MPa), a high maximum stress (201 MPa) and favorable ductility, being superior to the biomaterials with uniform porous structures in comprehensive mechanical properties. In addition, digital image correlation (DIC) and finite element (FE) simulation were used to unravel the mechanisms governing the deformation and yielding behavior of these biomaterials particularly at the strut junctions. Both DIC and FE simulations confirmed that the deformation and yielding of the FGPB occurred largely in the load-bearing layers but not at the interfaces between layers. Defect-coupled FE models based on solid elements provided further insights into the mechanical responses of the FGPB to compressive loads at both macro- and micro-scales. With the defect-coupled representative volume element model for the FGPB, the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The study clearly demonstrated the capabilities of combined experimental and computational methods to resolve the uncertainties of the mechanical behavior of FGPBs, which would open up the possibilities of applying various porosity variation strategies for the design of biomimetic AM porous biomaterials. STATEMENT OF SIGNIFICANCE: Functionally graded bone scaffolds significantly promote the recovery of segmental bone defect. In the present study, we present a step-wise topological design of functionally graded porous biomaterial (FGPB) to mimic the structure of the femoral diaphysis. The Ti-6Al-4V FGPB exhibited a superior combination of low density, moderate Young's modulus, high yield stress and maximum stress as well as favorable ductility. The biomechanical performance of FGPB was studied in both macro and micro perspectives. The defect-coupled model revealed the significant yielding in the load-bearing parts and the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The superiority of combined experimental and computational methods has been confirmed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Cellular solids structure and properties
Gibson, L. J., Ashby, M. F., et al. (1997) · Cited by 9,172
Cellular solids: Structure and properties
Wolcott, M. P. (1990) · Materials Science and Engineering: A · doi:10.1016/0921-5093(90)90295-e · Cited by 5,926
Porous scaffold design for tissue engineering
Hollister, S. J. (2005) · Nature Materials · doi:10.1038/nmat1421 · Cited by 3,969
Titanium alloys in total joint replacement—a materials science perspective
Long, M., & Rack, H. J. (1998) · Biomaterials · doi:10.1016/s0142-9612(97)00146-4 · Cited by 3,510
Biomaterials & scaffolds for tissue engineering
O'Brien, F. J. (2011) · Materials Today · doi:10.1016/s1369-7021(11)70058-x · Cited by 3,437
Wang, X., Xu, S., Zhou, S., Xu, W., Leary, M., Choong, P., Qian, M., Brandt, M., & Xie, Y. M. (2016) · Biomaterials · doi:10.1016/j.biomaterials.2016.01.012 · Cited by 2,121
BoneJ: Free and extensible bone image analysis in ImageJ
Doube, M., Kłosowski, M. M., Arganda-Carreras, I., Cordelières, F. P., Dougherty, R. P., Jackson, J. S., Schmid, B., Hutchinson, J. R., & Shefelbine, S. J. (2010) · Bone · doi:10.1016/j.bone.2010.08.023 · Cited by 2,040
Trabecular bone modulus–density relationships depend on anatomic site
Morgan, E. F., Bayraktar, H. H., & Keaveny, T. M. (2003) · Journal of Biomechanics · doi:10.1016/s0021-9290(03)00071-x · Cited by 1,209
Comparison of the elastic and yield properties of human femoral trabecular and cortical bone tissue
Bayraktar, H. H., Morgan, E. F., Niebur, G. L., Morris, G. E., Wong, E. K., & Keaveny, T. M. (2004) · Journal of Biomechanics · doi:10.1016/s0021-9290(03)00257-4 · Cited by 1,142
Printing and Prototyping of Tissues and Scaffolds
Derby, B. (2012) · Science · doi:10.1126/science.1226340 · Cited by 1,108
Cited by
Chowdhury, S., Yadaiah, N., Prakash, C., Ramakrishna, S., Dixit, S., Gupta, L. R., & Buddhi, D. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.07.121 · Cited by 784
Properties and applications of additively manufactured metallic cellular materials: A review
du Plessis, A., Razavi, N., Benedetti, M., Murchio, S., Leary, M., Watson, M., Bhate, D., & Berto, F. (2022) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100918 · Cited by 623
Li, Y., Feng, Z., Hao, L., Huang, L., Xin, C., Wang, Y., Bilotti, E., Essa, K., Zhang, H., Li, Z., et al. (2020) · Advanced Materials Technologies · doi:10.1002/admt.201900981 · Cited by 614
Additive manufacturing of functionally graded materials: A review
Zhang, C., Chen, F., Huang, Z., Jia, M., Chen, G., Ye, Y., Lin, Y., Liu, W., Chen, B., Shen, Q., et al. (2019) · Materials Science and Engineering: A · doi:10.1016/j.msea.2019.138209 · Cited by 612
Improving biocompatibility for next generation of metallic implants
Bandyopadhyay, A., Mitra, I., Goodman, S. B., Kumar, M., & Bose, S. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101053 · Cited by 463
Metadata
- Authors
- Zhang, X.-Y., Fang, G., Leeflang, S., Zadpoor, A. A., & Zhou, J.
- Venue
- Acta Biomaterialia
- Publisher
- Elsevier BV
- Published
- 2019-01
- Volume
- 84
- Pages
- 437-452
- ISSN
- 1742-7061 (ISSN-L)
- OpenAlex
- W2904951085
- Cited by
- 277
- References
- 56
- FWCI
- 15.99
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Topological design, permeability and mechanical behavior of additively manufactured functionally graded porous metallic biomaterials. https://app.cochat.ai/papers/10.1016/j.actbio.2018.12.013
- The paper
- Zhang, X.-Y., Fang, G., Leeflang, S., Zadpoor, A. A., & Zhou, J. (2019). Topological design, permeability and mechanical behavior of additively manufactured functionally graded porous metallic biomaterials. Acta Biomaterialia. https://doi.org/10.1016/j.actbio.2018.12.013
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.