The DOI matches its Crossref record; 21 of the 21 references it cites were found in a registry or an index.
An investigation into the porosity of extrusion-based 3D printed concrete
Abstract
Abstract Concrete structures additively manufactured by extrusion-based 3D concrete printing are reportedly orthotropic in mechanical behavior and exhibit relative weakness in interfacial regions. Microstructure, including porosity content, 3D porosity distribution and pore morphology presents a physical basis for these phenomena. Here, a first and comprehensive microstructural investigation is reported, using X-ray computed tomography to visualize and quantify porosity, pore sizes, shapes and distributions in extrusion-based 3D printed concrete. 3D printed plastic molds are used to sample specimens from freshly 3D printed concrete filaments, for minimum disturbance. As reference, similar specimens of the exact same concrete mix, but cast without compaction, instead of being 3D printed are included in the study. A fixed dimeter of 20 mm, but varying height is used to include a single filament layer (10 mm), two layers (20 mm) and four layers (40 mm). Both typical horizontal interfaces in multi-layer elements, and vertical interfaces between multilaterally deposited filaments are studied. Whilst a single 3D printable concrete mix are considered, print variables of pass time (0 to 60 minutes with 15 minute intervals) and print speed (80, 100 and 120 mm/s) are considered to investigate their potential alteration of the microstructure. Findings are significant, indicating tri-axial spheroid shaped air voids present in printed specimens, elongated and flat in the print direction, compared to mostly spherical voids in cast specimens. This prompts for more research to be conducted into the effect of stress concentrations at micro-cracks or voids in 3D printed concrete, which especially impacts mechanical behavior. Furthermore, it is found that vertical and horizontal interlayers comprise of similar porosity, and that it is inaccurate to qualify the homogeneity of typically fissile 3D printed concrete elements based solely on superficial cross-sectional photographic evidence from saw-cut samples.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
VI. The phenomena of rupture and flow in solids
Griffith, A. A. (1921) · Philosophical Transactions of the Royal Society of London. Series A, Containing Papers of a Mathematical or Physical Character · doi:10.1098/rsta.1921.0006 · Cited by 11,052
Hardened properties of high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Law, R., Gibb, A. G. F., & Thorpe, T. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.12.003 · Cited by 1,020
Wolfs, R. J. M., Bos, F. P., & Salet, T. A. M. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.02.017 · Cited by 836
Effect of surface moisture on inter-layer strength of 3D printed concrete
Sanjayan, J., Nematollahi, B., Xia, M., & Marchment, T. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.03.232 · Cited by 713
Nerella, V. N., Hempel, S., & Mechtcherine, V. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.01.235 · Cited by 605
Mechtcherine, V., Bos, F. P., Perrot, A., da Silva, W. R. L., Nerella, V. N., Fataei, S., Wolfs, R. J. M., Sonebi, M., & Roussel, N. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106037 · Cited by 598
du Plessis, A., Yadroitsev, I., Yadroitsava, I., & Le Roux, S. G. (2018) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2018.0060 · Cited by 550
Self-citationPanda, B., Noor Mohamed, N. A., Paul, S. C., Bhagath Singh, G., Tan, M. J., & Šavija, B. (2019) · Materials · doi:10.3390/ma12132149 · Cited by 301
Effects of interface roughness and interface adhesion on new-to-old concrete bonding
He, Y., Zhang, X., Hooton, R. D., & Zhang, X. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.05.049 · Cited by 295
Opportunities and challenges for structural engineering of digitally fabricated concrete
Menna, C., Mata-Falcón, J., Bos, F. P., Vantyghem, G., Ferrara, L., Asprone, D., Salet, T., & Kaufmann, W. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106079 · Cited by 251
Cited by
Kiani, P., Sedighi, M., Kasaeian-Naeini, M., & Jabbari, A. H. (2025) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2025.04.082 · Cited by 21
Metadata
- Authors
- Kruger, J., du Plessis, A., & van Zijl, G.
- Venue
- Additive Manufacturing
- Publisher
- Elsevier BV
- Published
- 2021-01
- Volume
- 37
- Pages
- 101740
- ISSN
- 2214-7810 (ISSN-L)
- 2214-8604
- OpenAlex
- W3110757799
- Cited by
- 263
- References
- 21
- FWCI
- 16.14
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: An investigation into the porosity of extrusion-based 3D printed concrete. https://app.cochat.ai/papers/10.1016/j.addma.2020.101740
- The paper
- Kruger, J., du Plessis, A., & van Zijl, G. (2021). An investigation into the porosity of extrusion-based 3D printed concrete. Additive Manufacturing. https://doi.org/10.1016/j.addma.2020.101740
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.