Student or educator? Sign up with your school email and get 6 months of Pro free.
Cited by 208

The DOI matches its Crossref record; 3 of the 3 references it cites were found in a registry or an index.

Catalytic microwave pyrolysis of waste engine oil using metallic pyrolysis char

Open access
Lam, Su Shiung, Liew, Rock Keey, Cheng, Chin Kui, Chase, Howard A. · 2015 · Applied Catalysis B: Environmental

Abstract

Microwave pyrolysis was performed on waste engine oil pre-mixed with different amounts of metallic-char catalyst produced previously from a similar microwave pyrolysis process. The metallic-char catalyst was first prepared by pretreatment with calcination followed by analyses to determine its various properties. The heating characteristics of the mixture of waste oil and metallic-char during the pyrolysis were investigated, and the catalytic influence of the metallic-char on the yield and characteristics of the pyrolysis products are discussed with emphasis on the composition of oil and gaseous products. The metallic-char, detected to have a porous structure and high surface area (124 m2/g), showed high thermal stability in a N2 atmosphere and it was also found to have phases of metals and metal oxides attached or adsorbed onto the char, representing a potentially suitable catalyst to be used in pyrolysis cracking process. The metallic-char initially acted as an adsorptive-support to adsorb metals, metal oxides and waste oil. Then, the char became a microwave absorbent that absorbed microwave energy and heated up to a high temperature in a short time and it was found to generate arcing and sparks during microwave pyrolysis of the waste oil, resulting in the formation of hot spots (high temperature sites with temperature up to 650 °C) within the reactor under the influence of microwave heating. The presence of this high temperature metallic-char, the amounts of which are likely to increase when increasing amounts of metallic-char were added to the waste oil (5, 10, and 20 wt% of the amount of waste oil added to the reactor), had provided a reducing chemical environment in which the metallic-char acted as an intermediate reductant to reduce the adsorbed metals or metal oxides into metallic states, which then functioned as a catalyst to provide more reaction sites that enhanced the cracking and heterogeneous reactions that occurred during the pyrolysis to convert the waste oil to produce higher yields of light hydrocarbons, H2 and CO gases in the pyrolysis products, recording a yield of up to 74 wt% of light C5–C10 hydrocarbons and 42 vol% of H2 and CO gases. The catalytic microwave pyrolysis produced 65–85 wt% yield of pyrolysis-oil containing C5–C20 hydrocarbons that can potentially be upgraded to produce transport-grade fuels. In addition, the recovered pyrolysis-gases (up to 33 wt%) were dominated by aliphatic hydrocarbons (up to 78 vol% of C1–C6 hydrocarbons) and significant amounts of valuable syngas (up to 42 vol% of H2 and CO in total) with low heating values (LHV) ranging from 4.7 to 5.5 MJ/m3, indicating that the pyrolysis-gases could also be used as a gaseous fuel or upgraded to produce more hydrogen as a second-generation fuel. The results indicate that the metallic-char shows advantages for use as a catalyst in microwave pyrolysis treatment of problematic waste oils.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1016/j.apcatb.2015.04.014

Cites

3 of 3 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 3 references

Cited by

See all 208

Metadata

Authors
Lam, S. S., Liew, R. K., Cheng, C. K., & Chase, H. A.
Venue
Applied Catalysis B: Environmental
Publisher
Elsevier BV
Published
2015-10
Volume
176-177
Pages
601-617
ISSN
0926-3373 (ISSN-L)
OpenAlex
W1964235881
Cited by
208
References
3
FWCI
12.90
Type
journal article
Language
en
Open access
green

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Catalytic microwave pyrolysis of waste engine oil using metallic pyrolysis char. https://app.cochat.ai/papers/10.1016/j.apcatb.2015.04.014
The paper
Lam, S. S., Liew, R. K., Cheng, C. K., & Chase, H. A. (2015). Catalytic microwave pyrolysis of waste engine oil using metallic pyrolysis char. Applied Catalysis B: Environmental. https://doi.org/10.1016/j.apcatb.2015.04.014

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.