The DOI matches its Crossref record; 42 of the 42 references it cites were found in a registry or an index.
The passivity of selective laser melted 316L stainless steel
Abstract
Abstract The passive film properties of as-received selective laser-melted 316L stainless steel (SLMed 316L SS) without obvious pores were studied and compared with those of wrought and solution-annealed (SA) SLMed 316L SSs. Among the samples, the as-received SLMed 316L SS had the lowest passive current density, which was attributed to two factors: the super high sub-grain boundary density increased the number of nucleation sites for passive film formation, and the micro-galvanic effect between the sub-grain boundary and the inner sub-grains also accelerated the rapid formation of a thick protective layer. The poor passivation and re-passivation abilities of the SA SLMed 316L SS were ascribed to the extensively precipitated nanosized oxide and sulfide particles, especially those at the grain boundary.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
3D printing of high-strength aluminium alloys
Martin, J. H., Yahata, B. D., Hundley, J. M., Mayer, J. A., Schaedler, T. A., & Pollock, T. M. (2017) · Nature · doi:10.1038/nature23894 · Cited by 2,950
Additively manufactured hierarchical stainless steels with high strength and ductility
Wang, Y. M., Voisin, T., McKeown, J. T., Ye, J., Calta, N. P., Li, Z., Zeng, Z., Zhang, Y., Chen, W., Roehling, T. T., et al. (2018) · Nature Materials · doi:10.1038/nmat5021 · Cited by 2,613
Additive manufacturing of Ti6Al4V alloy: A review
Liu, S., & Shin, Y. C. (2019) · Materials & Design · doi:10.1016/j.matdes.2018.107552 · Cited by 2,472
Metal Additive Manufacturing: A Review of Mechanical Properties
Lewandowski, J. J., & Seifi, M. (2016) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070115-032024 · Cited by 1,722
Kok, Y., Tan, X. P., Wang, P., Nai, M. L. S., Loh, N. H., Liu, E., & Tor, S. B. (2018) · Materials & Design · doi:10.1016/j.matdes.2017.11.021 · Cited by 1,447
Revealing the relationship between grain size and corrosion rate of metals
Ralston, K. D., Birbilis, N., & Davies, C. H. J. (2010) · Scripta Materialia · doi:10.1016/j.scriptamat.2010.08.035 · Cited by 1,141
Dislocation network in additive manufactured steel breaks strength–ductility trade-off
Liu, L., Ding, Q., Zhong, Y., Zou, J., Wu, J., Chiu, Y.-L., Li, J., Zhang, Z., Yu, Q., & Shen, Z. (2018) · Materials Today · doi:10.1016/j.mattod.2017.11.004 · Cited by 1,127
The history of the Point Defect Model for the passive state: A brief review of film growth aspects
Macdonald, D. D. (2011) · Electrochimica Acta · doi:10.1016/j.electacta.2010.11.005 · Cited by 1,117
Cited by
Additive manufacturing of steels: a review of achievements and challenges
Haghdadi, N., Laleh, M., Moyle, M., & Primig, S. (2021) · Journal of Materials Science · doi:10.1007/s10853-020-05109-0 · Cited by 622
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
About metastable cellular structure in additively manufactured austenitic stainless steels
Kong, D., Dong, C., Wei, S., Ni, X., Zhang, L., Li, R., Wang, L., Man, C., & Li, X. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2020.101804 · Cited by 528
Self-citation
Metadata
- Authors
- Kong, D., Dong, C., Ni, X., Zhang, L., Luo, H., Li, R., Wang, L., Man, C., & Li, X.
- Venue
- Applied Surface Science
- Publisher
- Elsevier BV
- Published
- 2020-02
- Volume
- 504
- Pages
- 144495
- ISSN
- 0169-4332 (ISSN-L)
- OpenAlex
- W2986452857
- Cited by
- 253
- References
- 42
- FWCI
- 14.22
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The passivity of selective laser melted 316L stainless steel. https://app.cochat.ai/papers/10.1016/j.apsusc.2019.144495
- The paper
- Kong, D., Dong, C., Ni, X., Zhang, L., Luo, H., Li, R., Wang, L., Man, C., & Li, X. (2020). The passivity of selective laser melted 316L stainless steel. Applied Surface Science. https://doi.org/10.1016/j.apsusc.2019.144495
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
