The DOI matches its Crossref record; 42 of the 44 references it cites were found in a registry or an index.
Impact behaviour of microparticles with microstructured surfaces: Experimental study and DEM simulation
Abstract
The surface topography of a component influences lots of important macroscopic phenomena, for example friction, fatigue and wear behaviour. This study is focused on the effect of surface topography on the collision behaviour of fine particles. To obtain this behaviour an experimental study of the single particle impact with a microstructured substrate was performed. A novel experimental setup was developed to capture collisions of small particles with the surface three-dimensionally. The particle-wall collisions were performed with spherical polystyrene microparticles. As contact partners a polished and a microstructured stainless steel substrate were used. The surface microstructure was produced by a cold spray process with spherical stainless steel particles. The measured restitution coefficient significantly decreased after the microstructuring showing an additional energy dissipation due to topography. The particle impact was simulated using the Discrete Element Method. The surface topography was implemented in the model by reverse engineering and meshed with two different resolutions. The simulations were compared with the experiments regarding the energy dissipation and rebound behaviour. The calculated restitution coefficient was in good agreement with the experiments for a fine meshed surface, but deviated significantly with the coarsened mesh.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The grid size has nothing to do with the solution accuracy [23].”
From Cold Spray Process for Co-Deposition of Copper and Aluminum Particles (2023) · cites this paper as [23]
Citations
Cites
A discrete numerical model for granular assemblies
Cundall, P. A., & Strack, O. D. L. (1979) · Géotechnique · doi:10.1680/geot.1979.29.1.47 · Cited by 17,527
Ueber die Berührung fester elastischer Körper.
Hertz, H. (1882) · crll · doi:10.1515/crll.1882.92.156 · Cited by 4,789
On the Contact of Elastic Solids
Hertz (1882) · Journal für die reine und angewandte Mathematik (Crelles Journal) · Cited by 3,051
Elastic Spheres in Contact Under Varying Oblique Forces
Mindlin, R. D., & Deresiewicz, H. (1953) · Journal of Applied Mechanics · doi:10.1115/1.4010702 · Cited by 2,782
Screened poisson surface reconstruction
Kazhdan, M., & Hoppe, H. (2013) · ACM Transactions on Graphics · doi:10.1145/2487228.2487237 · Cited by 2,231
Lagrangian numerical simulation of plug flow of cohesionless particles in a horizontal pipe
Tsuji, Y., Tanaka, T., & Ishida, T. (1992) · Powder Technology · doi:10.1016/0032-5910(92)88030-l · Cited by 2,147
Model for collisions in granular gases
Brilliantov, N. V., Spahn, F., Hertzsch, J.-M., & Pöschel, T. (1996) · Physical Review E · doi:10.1103/physreve.53.5382 · Cited by 892
A theoretical model for the stick/bounce behaviour of adhesive, elastic-plastic spheres
Thornton, C., & Ning, Z. (1998) · Powder Technology · doi:10.1016/s0032-5910(98)00099-0 · Cited by 832
Restitution Coefficient in a Collision between Two Spheres
Kuwabara, G., & Kono, K. (1987) · Japanese Journal of Applied Physics · doi:10.1143/jjap.26.1230 · Cited by 610
Coefficient of Restitution for Collinear Collisions of Elastic-Perfectly Plastic Spheres
Thornton, C. (1997) · Journal of Applied Mechanics · doi:10.1115/1.2787319 · Cited by 603
Research works printed but not linked: 1
- Antonyuk, 2010, Energy absorption during compression and impact of dry elastic-plastic spherical granules, Granul. Matter, 12, 15, 10.1007/s10035-009-0161-3 · DOI
Cited by
Contact mechanics for dynamical systems: a comprehensive review
Flores, P. (2021) · Multibody System Dynamics · doi:10.1007/s11044-021-09803-y · Cited by 152
The behaviors of particle-wall collision for non-spherical particles: Experimental investigation
Wang, J., Zhang, M., Feng, L., Yang, H., Wu, Y., & Yue, G. (2019) · Powder Technology · doi:10.1016/j.powtec.2019.12.041 · Cited by 49
Influence of the surface roughness on the collision behavior of fine particles in ambient fluids
Krull, F., Mathy, J., Breuninger, P., & Antonyuk, S. I. (2021) · Powder Technology · doi:10.1016/j.powtec.2021.06.051 · Cited by 48
Self-citationHesse, R., Krull, F., & Antonyuk, S. I. (2021) · Powder Technology · doi:10.1016/j.powtec.2021.07.056 · Cited by 44
Self-citationPowder Properties and Processing Conditions Affecting Cold Spray Deposition
Silvello, A., Cavaliere, P. D., Albaladejo-Fuentes, V., Martos, A., Dosta, S., & Cano, I. G. (2020) · Coatings · doi:10.3390/coatings10020091 · Cited by 36
Effect of Grain Size and Surface Roughness on the Normal Coefficient of Restitution of Single Grains
Sandeep, C. S., Luo, L., & Senetakis, K. (2020) · Materials · doi:10.3390/ma13040814 · Cited by 35
Hesse, R., Krull, F., & Antonyuk, S. I. (2020) · Powder Technology · doi:10.1016/j.powtec.2020.05.113 · Cited by 33
Self-citationMorgeneyer, M., Ramírez-Gómez, Á., Poletto, M., Ward-Smith, S., Tweedie, R. J., Heng, J. Y. Y., Maaß, S., & Bressot, C. (2018) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2018.11.029 · Cited by 30
Grohn, P., Oesau, T., Heinrich, S., & Antonyuk, S. I. (2022) · Advanced Powder Technology · doi:10.1016/j.apt.2022.103630 · Cited by 19
Self-citationThe effect of surface roughness on the viscoelastic energy dissipation in a particle–wall collision
Wang, Y., Zhang, Y., Fang, Z., & Wu, X. (2023) · Journal of Aerosol Science · doi:10.1016/j.jaerosci.2023.106280 · Cited by 17
Shi, X., Xie, F., Ji, J., Tian, Z., Xu, C., & Sun, A. (2024) · Powder Technology · doi:10.1016/j.powtec.2024.119387 · Cited by 17
Peridynamic Simulation of Particles Impact and Interfacial Bonding in Cold Spray Process
Ren, B., & Song, J. J. (2022) · Journal of Thermal Spray Technology · doi:10.1007/s11666-022-01409-w · Cited by 17
Fractionating of finest particles using cross-flow separation with superimposed electric field
Lösch, P., Nikolaus, K., & Antonyuk, S. I. (2020) · Separation and Purification Technology · doi:10.1016/j.seppur.2020.117820 · Cited by 17
Self-citationHesse, R., Lösch, P., & Antonyuk, S. I. (2023) · Advanced Powder Technology · doi:10.1016/j.apt.2023.104062 · Cited by 15
Self-citationContact Behavior of Microcrystalline Cellulose Pellets Depending on their Water Content
Grohn, P., Weis, D., Thommes, M., Heinrich, S., & Antonyuk, S. I. (2020) · Chemical Engineering & Technology · doi:10.1002/ceat.201900517 · Cited by 15
Self-citationInvestigation of the particle-loaden filtration performance for real fibre media using CFD-DEM
Fan, J., Wang, X., Xu, J., Yang, K., Chen, J., Wang, L., & Chen, J. (2024) · Particuology · doi:10.1016/j.partic.2024.11.015 · Cited by 13
Nie, W., Dou, Y., Xu, C., Peng, H., Liu, F., Li, H., Li, H., & Wan, J. (2024) · Process Safety and Environmental Protection · doi:10.1016/j.psep.2024.09.071 · Cited by 13
A contact model for the deformation behaviour of pharmaceutical pellets under cyclic loading
Weis, D., Krull, F., Mathy, J., Evers, M., Thommes, M., & Antonyuk, S. I. (2019) · Advanced Powder Technology · doi:10.1016/j.apt.2019.07.026 · Cited by 13
Self-citationElastic-plastic collision mechanism of micron-sized particle impacting rough surfaces
Yu, K., Peng, C., Shang, L., & Tafti, D. K. (2024) · Powder Technology · doi:10.1016/j.powtec.2024.119903 · Cited by 11
Saparbayeva, N., Chang, Y., Kosinski, P., Hoffmann, A. C., Balakin, B. V., & Struchalin, P. G. (2023) · Powder Technology · doi:10.1016/j.powtec.2023.118660 · Cited by 11
Impact behavior of hydrophilic microparticles on the particle-laden interface
Zhu, S., Zhao, C., Lin, J., Zhang, W., Sheng, Y., & Chen, X. (2020) · Chemical Engineering Science · doi:10.1016/j.ces.2020.115913 · Cited by 8
Krull, F., Strohner, D., Hering, J., von Freymann, G., & Antonyuk, S. I. (2023) · Advanced Powder Technology · doi:10.1016/j.apt.2023.104218 · Cited by 5
Self-citationComponent Surfaces: Manufacturing-Morphology-Property RelationshipsPreprint
Aurich, J. C., & Hasse, H. (2023) · doi:10.31224/3339 · Cited by 5
Experimental Methods for Model Parameters in the Discrete Element Method
Krull, F., Strohner, D., & Antonyuk, S. I. (2025) · KONA Powder and Particle Journal · doi:10.14356/kona.2026006 · Cited by 4
Self-citationCold Spray Process for Co-Deposition of Copper and Aluminum Particles
Hu, S., Li, H., Zhang, L., & Xu, Y. (2023) · Coatings · doi:10.3390/coatings13111953 · Cited by 3
Mao, W., Dai, Y. F., Yuan, X., Liang, H., & He, G. (2025) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2025.07.005 · Cited by 2
Experimental simulation of capillary effect on rough flat surfaces
Zuo, Z., Wang, J., Huo, Y., Wang, D., & Ji, H. (2021) · Particuology · doi:10.1016/j.partic.2021.03.011 · Cited by 2
Paas, S., Nikolaus, K., & Antonyuk, S. I. (2025) · Powders · doi:10.3390/powders4010006 · Cited by 1
Self-citationWang, G., Ruan, Q., Bickerdike, A., Zhu, L., & Liu, Y. (2026) · Nonlinear Dynamics · doi:10.1007/s11071-026-12846-5 · Cited by 1
Die Entwicklung der Verfahrenstechnik an der TU Kaiserslautern
Antonyuk, S. I., Bart, H., Hasse, H., Ripp, M., Ripperger, S., & Ulber, R. (2020) · Chemie Ingenieur Technik · doi:10.1002/cite.202000094
Self-citationInteractions Between Particles and Surfaces
de Payrebrune, K. M., Schönecker, C., Antonyuk, S. I., Bilz, R., Krull, F., Noichl, I., Ripperger, S., & Strohner, D. (2023) · Springer series in advanced manufacturing · doi:10.1007/978-3-031-35575-2_8
Self-citationGuo, Y. (2024) · DR-NTU (Nanyang Technological University) · doi:10.32657/10356/181797
Hasse, H. (. D.-I. ). (2023) · Publication Server of Kaiserslautern University of Technology (Kaiserslautern University of Technology)
Ren, B. (2024) · eScholarship@McGill (McGill) · doi:10.82308/17820
Study on the Collision Wear Characteristics of Particles on Moving WallsPreprint
Chen, D., Li, G., Ding, Y., Zhang, B., Zhang, C., & Lin, Z. (2026) · Research Square · doi:10.21203/rs.3.rs-8769899/v1
Wang, G., Ruan, Q., Liu, Y., & Liu, C. (2026) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2026.106471
Krull, F., Hering, J., von Freymann, G., & Antonyuk, S. I. (2026) · Powder Technology · doi:10.1016/j.powtec.2026.122638
Self-citationSuharno, B., Wicaksono, M. A., Astuti, W., & Rhamdhani, M. A. (2026) · JOM · doi:10.1007/s11837-026-08462-8
Metadata
- Authors
- Krull, F., Hesse, R., Breuninger, P., & Antonyuk, S.
- Affiliations
- University of Kaiserslautern (DE)
- Corresponding author
- Krull, Fabian
- Venue
- Chemical Engineering Research and Design
- Publisher
- Elsevier BV
- Published
- 2018-07
- Volume
- 135
- Pages
- 175-184
- ISSN
- 0263-8762 (ISSN-L)
- OpenAlex
- W2805846676
- Cited by
- 33
- References
- 44
- Citations by year
- 2026: 4 · 2025: 3 · 2024: 5 · 2023: 6 · 2022: 2 · 2021: 4 · 2020: 6 · 2019: 2 · 2018: 1
- FWCI
- 2.39
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
- www.elsevier.com/legal/tdmrep-license (tdm)
- Locations
- Process Safety and Environmental Protection (publishedVersion)
- Funders
- Deutsche Forschungsgemeinschaft (CRC 926)
- Topics
- Physical Sciences › Engineering › Computational Mechanics › Granular flow and fluidized beds
- Physical Sciences › Engineering › Mechanics of Materials › Adhesion, Friction, and Surface Interactions
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Particle Dynamics in Fluid Flows
- Keywords
- particle impact, surface topography, microstructured surfaces, coefficient of restitution, energy dissipation, particle-wall collision, polystyrene microparticles, cold spray, discrete element method, grid resolution
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.