The DOI matches its Crossref record; 42 of the 44 references it cites were found in a registry or an index.
Impact behaviour of microparticles with microstructured surfaces: Experimental study and DEM simulation
Abstract
The surface topography of a component influences lots of important macroscopic phenomena, for example friction, fatigue and wear behaviour. This study is focused on the effect of surface topography on the collision behaviour of fine particles. To obtain this behaviour an experimental study of the single particle impact with a microstructured substrate was performed. A novel experimental setup was developed to capture collisions of small particles with the surface three-dimensionally. The particle-wall collisions were performed with spherical polystyrene microparticles. As contact partners a polished and a microstructured stainless steel substrate were used. The surface microstructure was produced by a cold spray process with spherical stainless steel particles. The measured restitution coefficient significantly decreased after the microstructuring showing an additional energy dissipation due to topography. The particle impact was simulated using the Discrete Element Method. The surface topography was implemented in the model by reverse engineering and meshed with two different resolutions. The simulations were compared with the experiments regarding the energy dissipation and rebound behaviour. The calculated restitution coefficient was in good agreement with the experiments for a fine meshed surface, but deviated significantly with the coarsened mesh.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The grid size has nothing to do with the solution accuracy [23].”
From Cold Spray Process for Co-Deposition of Copper and Aluminum Particles (2023) · cites this paper as [23]
Citations
Cites
A discrete numerical model for granular assemblies
Cundall, P. A., & Strack, O. D. L. (1979) · Géotechnique · doi:10.1680/geot.1979.29.1.47 · Cited by 17,527
Ueber die Berührung fester elastischer Körper.
Hertz, H. (1882) · crll · doi:10.1515/crll.1882.92.156 · Cited by 4,789
On the Contact of Elastic Solids
Hertz (1882) · Journal für die reine und angewandte Mathematik (Crelles Journal) · Cited by 3,051
Elastic Spheres in Contact Under Varying Oblique Forces
Mindlin, R. D., & Deresiewicz, H. (1953) · Journal of Applied Mechanics · doi:10.1115/1.4010702 · Cited by 2,782
Screened poisson surface reconstruction
Kazhdan, M., & Hoppe, H. (2013) · ACM Transactions on Graphics · doi:10.1145/2487228.2487237 · Cited by 2,231
Lagrangian numerical simulation of plug flow of cohesionless particles in a horizontal pipe
Tsuji, Y., Tanaka, T., & Ishida, T. (1992) · Powder Technology · doi:10.1016/0032-5910(92)88030-l · Cited by 2,147
Model for collisions in granular gases
Brilliantov, N. V., Spahn, F., Hertzsch, J.-M., & Pöschel, T. (1996) · Physical Review E · doi:10.1103/physreve.53.5382 · Cited by 892
A theoretical model for the stick/bounce behaviour of adhesive, elastic-plastic spheres
Thornton, C., & Ning, Z. (1998) · Powder Technology · doi:10.1016/s0032-5910(98)00099-0 · Cited by 832
Restitution Coefficient in a Collision between Two Spheres
Kuwabara, G., & Kono, K. (1987) · Japanese Journal of Applied Physics · doi:10.1143/jjap.26.1230 · Cited by 610
Coefficient of Restitution for Collinear Collisions of Elastic-Perfectly Plastic Spheres
Thornton, C. (1997) · Journal of Applied Mechanics · doi:10.1115/1.2787319 · Cited by 603
Review and extension of normal force models for the Discrete Element Method
Kruggel-Emden, H., Simsek, E., Rickelt, S., Wirtz, S., & Scherer, V. (2007) · Powder Technology · doi:10.1016/j.powtec.2006.10.004 · Cited by 514
Experimental analysis and modelling of particle-wall collisions
Sommerfeld, M., & Huber, N. (1999) · International Journal of Multiphase Flow · doi:10.1016/s0301-9322(99)00047-6 · Cited by 463
Coefficient of restitution of colliding viscoelastic spheres
Ramirez, R., Pöschel, T., Brilliantov, N. V., & Schwager, T. (1999) · Physical review. E, Statistical physics, plasmas, fluids, and related interdisciplinary topics · doi:10.1103/physreve.60.4465 · Cited by 404
Micromechanics of granular materials
Adams, M. J. (1989) · Powder Technology · doi:10.1016/0032-5910(89)80057-9 · Cited by 289
Computational Granular Dynamics
(2005) · Springer eBooks · doi:10.1007/3-540-27720-x · Cited by 283
Rebound behaviour of spheres for plastic impacts
Wu, C., Li, L.-Y., & Thornton, C. (2003) · International Journal of Impact Engineering · doi:10.1016/s0734-743x(03)00014-9 · Cited by 281
Comparison of soft-sphere models to measurements of collision properties during normal impacts
Stevens, A. B., & Hrenya, C. M. (2005) · Powder Technology · doi:10.1016/j.powtec.2005.04.033 · Cited by 266
Energy absorption during compression and impact of dry elastic-plastic spherical granules
Antonyuk, S. I., Heinrich, S., Tomas, J., Deen, N. G., van Buijtenen, M. S., & Kuipers, J. A. M. (2010) · Granular Matter · doi:10.1007/s10035-009-0161-3 · Cited by 262
Self-citationAn experimental study of the elastic rebound of spheres
Kharaz, A. H., Gorham, D. A., & Salman, A. D. (2001) · Powder Technology · doi:10.1016/s0032-5910(01)00283-2 · Cited by 220
Micromechanics of Granular Materials
Cambou, B., Michel, J., & Radjaï, F. (2009) · Wiley eBooks · doi:10.1002/9780470611616 · Cited by 219
Collision dynamics of granular particles with adhesion
Brilliantov, N. V., Albers, N., Spahn, F., & Pöschel, T. (2007) · Physical Review E · doi:10.1103/physreve.76.051302 · Cited by 195
Impact breakage of spherical granules: Experimental study and DEM simulation
Antonyuk, S. I., Khanal, M., Tomas, J., Heinrich, S., & Mörl, L. (2006) · Chemical Engineering and Processing - Process Intensification · doi:10.1016/j.cep.2005.12.005 · Cited by 195
Self-citationCollision dynamics in fluidised bed granulators: A DEM-CFD study
Fries, L., Antonyuk, S. I., Heinrich, S., Dopfer, D., & Palzer, S. (2012) · Chemical Engineering Science · doi:10.1016/j.ces.2012.06.026 · Cited by 165
Self-citationLouge, M., & Adams, M. E. (2002) · Physical review. E, Statistical physics, plasmas, fluids, and related interdisciplinary topics · doi:10.1103/physreve.65.021303 · Cited by 147
Tribology in particulate technology
Dowson, D. (1988) · Wear · doi:10.1016/0043-1648(88)90057-9 · Cited by 146
Influence of liquid layers on energy absorption during particle impact
Antonyuk, S. I., Heinrich, S., Deen, N. G., & Kuipers, J. A. M. (2009) · Particuology · doi:10.1016/j.partic.2009.04.006 · Cited by 132
Self-citationFundamentals of cohesive powder consolidation and flow
Tomas, J. (2004) · Granular Matter · doi:10.1007/s10035-004-0167-9 · Cited by 119
Horabik, J., Beczek, M., Mazur, R., Parafiniuk, P., Ryżak, M., & Molenda, M. (2017) · Biosystems Engineering · doi:10.1016/j.biosystemseng.2017.06.009 · Cited by 102
Crüger, B., Salikov, V., Heinrich, S., Antonyuk, S. I., Sutkar, V. S., Deen, N. G., & Kuipers, J. A. M. (2015) · Particuology · doi:10.1016/j.partic.2015.04.002 · Cited by 99
Self-citationCoefficient of restitution as a fluctuating quantity
Montaine, M., Heckel, M., Kruelle, C. A., Schwager, T., & Pöschel, T. (2011) · Physical Review E · doi:10.1103/physreve.84.041306 · Cited by 73
Experimental study of oblique impact of particles on wet surfaces
Crüger, B., Heinrich, S., Antonyuk, S. I., Deen, N. G., & Kuipers, J. A. M. (2016) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2016.01.024 · Cited by 59
Self-citationAdhesion of ultrafine particles—Energy absorption at contact
Tomas, J. (2007) · Chemical Engineering Science · doi:10.1016/j.ces.2007.06.036 · Cited by 57
Experiments and Engineering Models of Microparticle Impact and Deposition
Brach, R. M., Dunn, P. F., & Li, X. (2000) · The Journal of Adhesion · doi:10.1080/00218460008034531 · Cited by 54
Schilde, C., Burmeister, C. F., & Kwade, A. (2014) · Powder Technology · doi:10.1016/j.powtec.2014.03.042 · Cited by 52
Ti surface modification by cold spraying with TiO 2 microparticles
Schmidt, K., Buhl, S., Davoudi, N., Godard, C., Merz, R., Raid, I., Kerscher, E., Kopnarski, M., Müller−Renno, C., Ripperger, S., et al. (2016) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2016.10.091 · Cited by 45
Self-citationMechanoluminescence of quartz particles during grinding in a stirred media mill
Aman, S., & Tomas, J. (2004) · Powder Technology · doi:10.1016/j.powtec.2004.08.005 · Cited by 27
Rebound behavior of nanoparticle-agglomerates
Gensch, M., & Weber, A. P. (2017) · Advanced Powder Technology · doi:10.1016/j.apt.2017.05.003 · Cited by 23
Comparative evaluation of normal viscoelastic contact force models in low velocity impact situations
Kačianauskas, R., Kruggel‐Emden, H., Zdancevičius, E., & Markauskas, D. (2016) · Advanced Powder Technology · doi:10.1016/j.apt.2016.04.031 · Cited by 20
McNamara, S. C., & Falcon, É. (2007) · Powder Technology · doi:10.1016/j.powtec.2007.06.026 · Cited by 17
Drücker, S., Krautstrunk, I., Paulick, M., Saleh, K., Morgeneyer, M., & Kwade, A. (2016) · Journal of Visualized Experiments · doi:10.3791/53299 · Cited by 14
Mader‐Arndt, K., Aman, S., Fuchs, R., & Tomas, J. (2016) · Advanced Powder Technology · doi:10.1016/j.apt.2016.09.014 · Cited by 9
ROTATIONAL DISSIPATION DURING MICROSPHERE IMPACT
Brach, R. M., Dunn, P. F., & Cheng, W. (1999) · Journal of Aerosol Science · doi:10.1016/s0021-8502(99)00031-2 · Cited by 8
Research works printed but not linked: 1
- Antonyuk, 2010, Energy absorption during compression and impact of dry elastic-plastic spherical granules, Granul. Matter, 12, 15, 10.1007/s10035-009-0161-3 · DOI
Cited by
Contact mechanics for dynamical systems: a comprehensive review
Flores, P. (2021) · Multibody System Dynamics · doi:10.1007/s11044-021-09803-y · Cited by 152
The behaviors of particle-wall collision for non-spherical particles: Experimental investigation
Wang, J., Zhang, M., Feng, L., Yang, H., Wu, Y., & Yue, G. (2019) · Powder Technology · doi:10.1016/j.powtec.2019.12.041 · Cited by 49
Influence of the surface roughness on the collision behavior of fine particles in ambient fluids
Krull, F., Mathy, J., Breuninger, P., & Antonyuk, S. I. (2021) · Powder Technology · doi:10.1016/j.powtec.2021.06.051 · Cited by 48
Self-citationHesse, R., Krull, F., & Antonyuk, S. I. (2021) · Powder Technology · doi:10.1016/j.powtec.2021.07.056 · Cited by 44
Self-citationPowder Properties and Processing Conditions Affecting Cold Spray Deposition
Silvello, A., Cavaliere, P. D., Albaladejo-Fuentes, V., Martos, A., Dosta, S., & Cano, I. G. (2020) · Coatings · doi:10.3390/coatings10020091 · Cited by 36
Metadata
- Authors
- Krull, F., Hesse, R., Breuninger, P., & Antonyuk, S.
- Affiliations
- University of Kaiserslautern (DE)
- Corresponding author
- Krull, Fabian
- Venue
- Chemical Engineering Research and Design
- Publisher
- Elsevier BV
- Published
- 2018-07
- Volume
- 135
- Pages
- 175-184
- ISSN
- 0263-8762 (ISSN-L)
- OpenAlex
- W2805846676
- Cited by
- 33
- References
- 44
- Citations by year
- 2026: 4 · 2025: 3 · 2024: 5 · 2023: 6 · 2022: 2 · 2021: 4 · 2020: 6 · 2019: 2 · 2018: 1
- FWCI
- 2.39
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
- www.elsevier.com/legal/tdmrep-license (tdm)
- Locations
- Process Safety and Environmental Protection (publishedVersion)
- Funders
- Deutsche Forschungsgemeinschaft (CRC 926)
- Topics
- Physical Sciences › Engineering › Computational Mechanics › Granular flow and fluidized beds
- Physical Sciences › Engineering › Mechanics of Materials › Adhesion, Friction, and Surface Interactions
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Particle Dynamics in Fluid Flows
- Keywords
- particle impact, surface topography, microstructured surfaces, coefficient of restitution, energy dissipation, particle-wall collision, polystyrene microparticles, cold spray, discrete element method, grid resolution
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.