The DOI matches its Crossref record; 33 of the 33 references it cites were found in a registry or an index.
Control of NOx and other emissions in micro gas turbine combustors fuelled with mixtures of methane and ammonia
Open accessAbstract
Abstract Methane–ammonia mixtures have potentials as low-carbon fuels for gas turbines, however significantly high fuel NOx production in their flames present challenges to their application. This study aims to provide deep insight into the physical and chemical processes involved in the formation and control of emissions from the combustion of CH4 NH3–air with up to 30% ammonia by heat fraction in gas turbine combustors. Hence, laser diagnostics techniques such as Particle Image Velocimetry (PIV), and Planar Laser Induced Fluorescence (PLIF) imaging, in addition to Fourier Transform Infrared (FTIR) gas analysis were employed to study the flow field, flame structure and emissions characteristics of a micro gas turbine swirl combustor fuelled with CH4 NH3–air mixtures. The control of emissions from the flames was further studied using Large Eddy Simulation (LES) of a model swirl combustor. The results show that NOx emissions from premixed CH4 NH3–air in single-stage combustion were more than 5000 ppmv at equivalence ratios, Φ = 0.8–1.1, which is about twice more than the values already reported for NH3–air. Trends in NOx emissions correspond with the trends in OH radicals concentration in the combustor owing to the relevance of OH radicals in fuel NOx production. Emissions control leading to significantly low emissions such as 49 ppmv of NOx, 2 ppmv of CO and approximately zero N2O, HCN and NH3 emissions with a 99.8% combustion efficiency was achieved using rich-lean combustion. An optimum Φ of the primary combustion zone for low NOx emission was identified, which varied from 1.30 to 1.35 depending on the ammonia fraction. For Φ richer (leaner) than the optimum Φ, NOx emission increased due to an increase in NOx production in the secondary (primary) combustion zone. Rich-lean combustion of CH4 NH3–air emitted less NOx than that of NH3-air because the higher flame speed of CH4 NH3–air mixtures ensured lower NOx production in the secondary combustion zone.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Subgrid-scale stress modelling based on the square of the velocity gradient tensor
Nicoud, F., & Ducros, F. (1999) · Flow, Turbulence and Combustion · doi:10.1023/a:1009995426001 · Cited by 4,161
Valera-Medina, A., Xiao, H., Owen-Jones, M., David, W. I. F., & Bowen, P. J. (2018) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2018.07.001 · Cited by 2,730
Science and technology of ammonia combustion
Kobayashi, H., Hayakawa, A., Somarathne, K. D. K. A., & Okafor, E. C. (2019) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2018.09.029 · Cited by 2,532
Self-citationModeling nitrogen chemistry in combustion
Glarborg, P., Miller, J. A., Ruscic, B., & Klippenstein, S. J. (2018) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2018.01.002 · Cited by 1,998
Experimental and numerical study of the laminar burning velocity of CH4–NH3–air premixed flames
Okafor, E. C., Naito, Y., Colson, S., Ichikawa, A., Kudo, T., Hayakawa, A., & Kobayashi, H. (2018) · Combustion and Flame · doi:10.1016/j.combustflame.2017.09.002 · Cited by 1,068
Self-citationSyred, N. (2006) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2005.10.002 · Cited by 1,031
Han, X., Wang, Z., Costa, M., Sun, Z., He, Y., & Cen, K. (2019) · Combustion and Flame · doi:10.1016/j.combustflame.2019.05.003 · Cited by 869
Reiter, A. J., & Kong, S.-C. (2011) · Fuel · doi:10.1016/j.fuel.2010.07.055 · Cited by 858
Laminar burning velocity and Markstein length of ammonia/air premixed flames at various pressures
Hayakawa, A., Goto, T., Mimoto, R., Arakawa, Y., Kudo, T., & Kobayashi, H. (2015) · Fuel · doi:10.1016/j.fuel.2015.06.070 · Cited by 854
Self-citationOkafor, E. C., Naito, Y., Colson, S., Ichikawa, A., Kudo, T., Hayakawa, A., & Kobayashi, H. (2019) · Combustion and Flame · doi:10.1016/j.combustflame.2019.03.008 · Cited by 593
Self-citationKurata, O., Iki, N., Matsunuma, T., Inoue, T., Tsujimura, T., Furutani, H., Kobayashi, H., & Hayakawa, A. (2017) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2016.07.088 · Cited by 582
Self-citationIchikawa, A., Hayakawa, A., Kitagawa, Y., Kunkuma Amila Somarathne, K. D., Kudo, T., & Kobayashi, H. (2015) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2015.04.024 · Cited by 540
Self-citationThe role of NNH in NO formation and control
Klippenstein, S. J., Harding, L. B., Glarborg, P., & Miller, J. A. (2011) · Combustion and Flame · doi:10.1016/j.combustflame.2010.12.013 · Cited by 497
Ammonia–methane combustion in tangential swirl burners for gas turbine power generation
Valera-Medina, A., Marsh, R., Runyon, J., Pugh, D., Beasley, P., Hughes, T., & Bowen, P. (2017) · Applied Energy · doi:10.1016/j.apenergy.2016.02.073 · Cited by 480
Study on using hydrogen and ammonia as fuels: Combustion characteristics and NOxformation
Li, J., Huang, H., Kobayashi, N., He, Z., & Nagai, Y. (2014) · International Journal of Energy Research · doi:10.1002/er.3141 · Cited by 462
Reiter, A. J., & Kong, S.-C. (2008) · Energy & Fuels · doi:10.1021/ef800140f · Cited by 440
Towards the development of an efficient low-NOx ammonia combustor for a micro gas turbine
Okafor, E. C., Somarathne, K. D. K. A., Hayakawa, A., Kudo, T., Kurata, O., Iki, N., & Kobayashi, H. (2019) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2018.07.083 · Cited by 439
Self-citationKinetic Modeling of the Oxidation of Ammonia in Flames
Miller, J. A., Smooke, M. D., Green, R. M., & Kee, R. J. (1983) · Combustion Science and Technology · doi:10.1080/00102208308923691 · Cited by 426
The oxidation of hydrogen cyanide and related chemistry
DAGAUT, P., GLARBORG, P., & ALZUETA, M. (2008) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2007.02.004 · Cited by 395
He, X., Shu, B., Nascimento, D., Moshammer, K., Costa, M., & Fernandes, R. X. (2019) · Combustion and Flame · doi:10.1016/j.combustflame.2019.04.050 · Cited by 370
Somarathne, K. D. K. A., Hatakeyama, S., Hayakawa, A., & Kobayashi, H. (2017) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2017.09.089 · Cited by 319
Self-citationKumar, P., & Meyer, T. R. (2013) · Fuel · doi:10.1016/j.fuel.2012.06.103 · Cited by 314
da Rocha, R. C., Costa, M., & Bai, X.-S. (2019) · Fuel · doi:10.1016/j.fuel.2019.02.102 · Cited by 295
Pugh, D., Bowen, P., Valera-Medina, A., Giles, A., Runyon, J., & Marsh, R. (2019) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2018.07.091 · Cited by 256
Ammonia, Methane and Hydrogen for Gas Turbines
Valera-Medina, A., Morris, S., Runyon, J., Pugh, D. G., Marsh, R., Beasley, P., & Hughes, T. (2015) · Energy Procedia · doi:10.1016/j.egypro.2015.07.205 · Cited by 230
Contino, F., Jeanmart, H., Lucchini, T., & D’Errico, G. (2011) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2010.08.002 · Cited by 185
Homogeneous formation of NO and N2O from the oxidation of HCN and NH3 at 600–1000°C
Wargadalam, V. J., Löffler, G., Winter, F., & Hofbauer, H. (2000) · Combustion and Flame · doi:10.1016/s0010-2180(99)00107-8 · Cited by 170
Ramos, C. F., da Rocha, R. C., Oliveira, P. M. R., et al. (2019) · Fuel · doi:10.1016/j.fuel.2019.115693 · Cited by 154
Stopper, U., Meier, W., Sadanandan, R., Stöhr, M., Aigner, M., & Bulat, G. (2013) · Combustion and Flame · doi:10.1016/j.combustflame.2013.04.005 · Cited by 130
Burning velocity and flame structure of CH4/NH3/air turbulent premixed flames at high pressure
Ichikawa, A., Naito, Y., Hayakawa, A., et al. (2019) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2019.01.193 · Cited by 118
Self-citationPERFORMANCE OF AMMONIA-FIRED GAS-TURBINE COMBUSTORS
Pratt, D. T. (1967) · doi:10.21236/ad0657585 · Cited by 86
Somarathne, K. D. K. A., Hayakawa, A., & Kobayashi, H. (2016) · Journal of Fluid Science and Technology · doi:10.1299/jfst.2016jfst0026 · Cited by 81
Self-citationJójka, J., & Ślefarski, R. (2018) · Fuel · doi:10.1016/j.fuel.2017.12.070 · Cited by 42
Cited by
Review on Ammonia as a Potential Fuel: From Synthesis to Economics
Valera-Medina, A., Amer-Hatem, F., Azad, A. K., Dedoussi, I. C., de Joannon, M., Fernandes, R. X., Glarborg, P., Hashemi, H., He, X., Mashruk, S., et al. (2021) · Energy & Fuels · doi:10.1021/acs.energyfuels.0c03685 · Cited by 1,061
A review on ammonia, ammonia-hydrogen and ammonia-methane fuels
Chai, W. S., Bao, Y., Jin, P., Tang, G., & Zhou, L. (2021) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2021.111254 · Cited by 1,028
Review on the recent advances on ammonia combustion from the fundamentals to the applications
Elbaz, A. M., Wang, S., Guiberti, T. F., & Roberts, W. L. (2022) · Fuel Communications · doi:10.1016/j.jfueco.2022.100053 · Cited by 639
Advancements of combustion technologies in the ammonia-fuelled engines
Chiong, M.-C., Chong, C. T., Ng, J.-H., Mashruk, S., Chong, W. W. F., Samiran, N. A., Mong, G. R., & Valera-Medina, A. (2021) · Energy Conversion and Management · doi:10.1016/j.enconman.2021.114460 · Cited by 529
Ammonia/Methane combustion: Stability and NOx emissions
Ariemma, G. B., Sorrentino, G., Ragucci, R., de Joannon, M., & Sabia, P. (2022) · Combustion and Flame · doi:10.1016/j.combustflame.2022.112071 · Cited by 321
Metadata
- Authors
- Okafor, E. C., Somarathne, K. D. K. A., Ratthanan, R., Hayakawa, A., Kudo, T., Kurata, O., Iki, N., Tsujimura, T., Furutani, H., & Kobayashi, H.
- Venue
- Combustion and Flame
- Publisher
- Elsevier BV
- Published
- 2020-01
- Volume
- 211
- Pages
- 406-416
- ISSN
- 0010-2180 (ISSN-L)
- OpenAlex
- W2982252007
- Cited by
- 464
- References
- 33
- FWCI
- 21.19
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.