Cited by 26Concrete and Cement Materials ResearchRecycling and utilization of industrial and municipal waste in materials productionGeotechnical Engineering and Soil Stabilization

The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.

Experimental study on solidification/stabilisation of high-salt sludge by alkali-activated GGBS and MSWI bottom ash cementitious materials

Open access
Feng, Deluan, Wang, Jie, Wang, Yuxin, Liang, Shihua·2023·Case Studies in Construction Materials

Abstract

This study utilises alkali-activated ground granulated blast furnace slag (GGBS) as the primary method for solidification/stabilisation, with municipal solid waste incineration (MSWI) bottom ash (BA) as an auxiliary precursor to assist in the solidification/stabilisation (S/S) of high-salt sludge. The results show that the alkali-activated GGBS and MSWI BA cementitious material can effectively realize the S/S of high-salt sludge. However, having early strength of the alkali-activated GGBS solidified sludge at low GGBS content is difficult. In comparison, the addition of MSWI BA enhances the unconfined compressive strength (UCS) of the alkali-activated GGBS solidified sludge to reach 6.35 MPa at 3d curing age, whereas the UCS of the alkali-activated GGBS solidified sludge with 20% GGBS achieves only 0.31 MPa at 14d curing age. The MSWI BA significantly improves the effect of S/S on high-salt sludge by alkali-activated GGBS, and the solidified high-salt sludge with 20% alkali-activated GGBS and MSWI BA cementitious material exhibits good water stability, the UCS of which retain 2.33 MPa after 28d water immersion. The analysis of the mineral composition, chemical bond transformation, thermal stability and microstructure of the solidified sludge samples indicates that the geopolymer cementitious material generated by alkali-activated GGBS and MSWI BA can effectively cement and wrap sludge particles and soluble salts, and reduce the strength loss of the solidified samples after water immersion. Moreover, the addition of MSWI BA accelerates the polymerization of alkali-activated GGBS, leading to rapid solidification/stabilisation of high-salt sludge in early curing age and reduction of the consumption of mineral resources. The heavy metal leaching concentration of the solidified sludge is much lower than that of the raw MSWI BA, and can satisfy the pollution control standard limit of landfill. The immobilization efficiency of the heavy metals of the solidified sludge is larger than 89%. By using MSWI BA as an auxiliary precursor in alkali-activated GGBS, the co-disposal of high-salt sludge and MSWI BA can be achieved, providing insights for realizing the energy conservation and environment protection purposes of solid waste reclamation and GGBS consumption reduction.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1016/j.cscm.2023.e02417

Cites

1 of 1 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 1 references

Research works printed but not linked: 76

  1. Song, 2015, Minimizing the increasing solid waste through zero waste strategy, J. Clean. Prod., 104, 199, 10.1016/j.jclepro.2014.08.027 · DOI
  2. Guerrero, 2013, Solid waste management challenges for cities in developing countries, Waste Manag., 33, 220, 10.1016/j.wasman.2012.09.008 · DOI · Paper page
  3. Kumar, 2017, A review on technological options of waste to energy for effective management of municipal solid waste, Waste Manag., 69, 407, 10.1016/j.wasman.2017.08.046 · DOI
  4. Miezah, 2015, Municipal solid waste characterization and quantification as a measure towards effective waste management in Ghana, Waste Manag., 46, 15, 10.1016/j.wasman.2015.09.009 · DOI
  5. Safiuddin, 2010, Utilization of solid wastes in construction materials, Int. J. Phys. Sci., 5, 1952
  6. Tome, 2020, Improved reactivity of volcanic ash using municipal solid incinerator fly ash for alkali-activated cement synthesis, Waste Biomass-.-. Valoriz., 11, 3035, 10.1007/s12649-019-00604-1 · DOI
  7. Tome, 2018, Characterization and leachability behaviour of geopolymer cement synthesised from municipal solid waste incinerator fly ash and volcanic ash blends, Recycling, 3, 14, 10.3390/recycling3040050 · DOI
  8. Lancellotti, 2010, Chemical stability of geopolymers containing municipal solid waste incinerator fly ash, Waste Manag., 30, 673, 10.1016/j.wasman.2009.09.032 · DOI
  9. Li, 2019, Comprehensive utilization and environmental risks of coal gangue: a review, J. Clean. Prod., 239, 18, 10.1016/j.jclepro.2019.117946 · DOI
  10. Vidhya, 2016, Experimental investigations on the properties of coal-ash brick units as green building materials, Int. J. Coal Prep. Util., 36, 318, 10.1080/19392699.2015.1118379 · DOI
  11. 2001, Standard for pollution control on the municipal solid waste incineration, State General Administration of Quality Supervision, Insp. Quar.
  12. Margallo, 2015, Environmental sustainability assessment of the management of municipal solid waste incineration residues: a review of the current situation, Clean. Technol. Environ. Policy, 17, 1333, 10.1007/s10098-015-0961-6 · DOI
  13. Margallo, 2015, Environmental sustainability assessment of the management of municipal solid waste incineration residues: a review of the current situation, Clean. Technol. Environ. Policy, 17, 1333, 10.1007/s10098-015-0961-6 · DOI
  14. Yin, 2018, Environmental perspectives of recycling various combustion ashes in cement production - a review, Waste Manag., 78, 401, 10.1016/j.wasman.2018.06.012 · DOI
  15. Huang, 2020, Influence of NaOH content on the alkali conversion mechanism in MSWI bottom ash alkali-activated mortars, Constr. Build. Mater., 248, 10, 10.1016/j.conbuildmat.2020.118582 · DOI
  16. Chen, 2022, Preparation of Alkali Activated Cementitious Material by Upgraded Fly Ash from MSW Incineration, Int. J. Environ. Res. Public Health, 19, 17, 10.3390/ijerph192013666 · DOI
  17. Huang, 2020, Use of pretreatment to prevent expansion and foaming in high-performance MSWI bottom ash alkali-activated mortars, Constr. Build. Mater., 245, 10, 10.1016/j.conbuildmat.2020.118471 · DOI
  18. Kizinievic, 2022, Impact of municipal solid waste incineration bottom ash on the properties and frost resistance of clay bricks, J. Mater. Cycles Waste Manag., 24, 237, 10.1007/s10163-021-01314-4 · DOI
  19. Sappa, 2019, The LCA methodology for ceramic tiles production by addition of MSWI BA, Resourrces, 8, 21
  20. Lou, 2015, Martial recycling from renewable landfill and associated risks: a review, Chemosphere, 131, 91, 10.1016/j.chemosphere.2015.02.036 · DOI
  21. Renou, 2008, Landfill leachate treatment: review and opportunity, J. Hazard. Mater., 150, 468, 10.1016/j.jhazmat.2007.09.077 · DOI
  22. Wiszniowski, 2006, Landfill leachate treatment methods: a review, Environ. Chem. Lett., 4, 51, 10.1007/s10311-005-0016-z · DOI
  23. Pathak, 2009, Bioleaching of heavy metals from sewage sludge: A review, J. Environ. Manag., 90, 2343, 10.1016/j.jenvman.2008.11.005 · DOI
  24. Malviya, 2006, Factors affecting hazardous waste solidification/stabilization: a review, J. Hazard. Mater., 137, 267, 10.1016/j.jhazmat.2006.01.065 · DOI
  25. Conner, 1998, A critical review of stabilization/solidification technology, Crit. Rev. Environ. Sci. Technol., 28, 397, 10.1080/10643389891254250 · DOI
  26. Provis, 2015, Advances in understanding alkali-activated materials, Cem. Concr. Res., 78, 110, 10.1016/j.cemconres.2015.04.013 · DOI
  27. Rodriguez, 2008, Alternative concrete based on alkali-activated slag, Mater. Constr., 58, 53, 10.3989/mc.2008.v58.i291.104 · DOI
  28. Wang, 2016, Preparation and properties of geopolymer based on construction waste-slag, J. Mater. Sciernce Eng., 34, 895
  29. Tang, 2021, Effect of salinity on soil structure and soil hydraulic characteristics, Can. J. Soil Sci., 101, 62, 10.1139/cjss-2020-0018 · DOI
  30. Franca, 2023, Preliminary reactivity test for precursors of alkali-activated, Mater. Build, 13, 19
  31. Junyong, 2016, The micro-structure of saline soil in qarham salt lake and its mechanics characteristics, Chin. J. Undergr. Space Eng., 12, 1277
  32. Risdanareni, 2020, Belie, The effect of NaOH concentration on the mechanical and physical properties of alkali activated fly ash-based artificial lightweight aggregate, Constr. Build. Mater., 259, 8, 10.1016/j.conbuildmat.2020.119832 · DOI
  33. Rakhimova, 2021, Phase formation behavior of alkali-activated calcined clays: effects of the reactive phase and NaOH concentration, Geosystem Eng., 24, 238, 10.1080/12269328.2021.1961615 · DOI
  34. de Vargas, 2014, Strength development of alkali-activated fly ash produced with combined NaOH and Ca(OH)(2) activators, Cem. Concr. Compos., 53, 341, 10.1016/j.cemconcomp.2014.06.012 · DOI
  35. Thunuguntla, 2018, Appraisal on strength characteristics of alkali-activated GGBFS with low concentrations of sodium hydroxide, Iran. J. Sci. Technol. -Trans. Civ. Eng., 42, 231, 10.1007/s40996-018-0113-4 · DOI
  36. Zhang, 2021, Use of municipal solid waste incineration bottom ash as a supplementary cementitious material in dry-cast concrete, Constr. Build. Mater., 266, 12, 10.1016/j.conbuildmat.2020.120890 · DOI
  37. Yin, 2018, Environmental perspectives of recycling various combustion ashes in cement production - a review, Waste Manag., 78, 401, 10.1016/j.wasman.2018.06.012 · DOI
  38. Zhang, 2022, A review on shrinkage-reducing methods and mechanisms of alkali-activated/geopolymer systems, Eff. Chem. Addit., J. Build. Eng., 49, 27
  39. Tortora, 2022, Effect of temperature and humidity on the synthesis of alkali-activated binders based on bottom ash from municipal waste incineration, Sustainability, 14, 18, 10.3390/su14031848 · DOI
  40. Huang, 2019, Cooperative action and compatibility between Portland cement and MSWI bottom ash alkali-activated double gel system materials, Constr. Build. Mater., 209, 445, 10.1016/j.conbuildmat.2019.03.141 · DOI
  41. Wong, 2015, Hydrophobic concrete using waste paper sludge ash, Cem. Concr. Res., 70, 9, 10.1016/j.cemconres.2015.01.005 · DOI
  42. Gu, 2018, Using alkali-activated cementitious materials to solidify high organic matter content dredged sludge as roadbed material, Adv. Civ. Eng., 2018, 10
  43. Xiao, 2019, Recycling of oily sludge as a roadbed material utilizing phosphogypsum-based cementitious, Mater., Adv. Civ. Eng., 2019, 10
  44. Dong, 2021, Silica fume-reinforced alkali-activated uncalcined Pisha Sandstone-based geopolymer cement, Constr. Build. Mater., 269, 10, 10.1016/j.conbuildmat.2020.121296 · DOI
  45. Wongsa, 2017, Use of municipal solid waste incinerator (MSWI) bottom ash in high calcium fly ash geopolymer matrix, J. Clean. Prod., 148, 49, 10.1016/j.jclepro.2017.01.147 · DOI
  46. Dou, 2017, Review of MSWI bottom ash utilization from perspectives of collective characterization, treatment and existing application, Renew. Sust. Energ. Rev., 79, 24, 10.1016/j.rser.2017.05.044 · DOI
  47. Long, 2023, Improving stabilization/solidification of MSWI fly ash with coal gangue based geopolymer via increasing active calcium content, Sci. Total Environ., 854, 9, 10.1016/j.scitotenv.2022.158594 · DOI
  48. Li, 2021, Experimental study on calcium carbide residue as a combined activator for coal gangue geopolymer and feasibility for soil stabilization, Constr. Build. Mater., 312, 12, 10.1016/j.conbuildmat.2021.125465 · DOI
  49. Liu, 2021, Utilisation of municipal solid waste incinerator (MSWI) fl y ash with metakaolin for preparation of alkali-activated cementitious material, J. Hazard. Mater., 402, 12, 10.1016/j.jhazmat.2020.123451 · DOI
  50. Vasic, 2022, Alkali-activated geopolymerization of a low illitic raw clay and waste brick mixture, Altern. Tradit. Ceram. Appl. Clay Sci., 218, 14
  51. Sun, 2018, Pervious concrete made of alkali activated slag and geopolymers, Constr. Build. Mater., 189, 797, 10.1016/j.conbuildmat.2018.09.067 · DOI
  52. Li, 2021, Experimental study on calcium carbide residue as a combined activator for coal gangue geopolymer and feasibility for soil stabilization, Constr. Build. Mater., 312, 12, 10.1016/j.conbuildmat.2021.125465 · DOI
  53. Collepardi, 2003, A state-of-the-art review on delayed ettringite attack on concrete, Cem. Concr. Compos., 25, 401, 10.1016/S0958-9465(02)00080-X · DOI
  54. Tan, 2022, Co-disposal of construction and demolition waste (CDW) and municipal solid waste incineration fly ash (MSWI FA) through geopolymer technology, J. Clean. Prod., 362, 12, 10.1016/j.jclepro.2022.132502 · DOI
  55. Wan, 2011, Learning about novel amine-adduct curing agents for epoxy resins: butyl-glycidylether-modified poly(propyleneimine) dendrimers, Thermochim. Acta, 519, 72, 10.1016/j.tca.2011.02.038 · DOI
  56. Huang, 2019, Cooperative action and compatibility between Portland cement and MSWI bottom ash alkali-activated double gel system materials, Constr. Build. Mater., 209, 445, 10.1016/j.conbuildmat.2019.03.141 · DOI
  57. Luo, 2022, Co-disposal of MSWI fly ash and lead-zinc smelting slag through alkali-activation technology, Constr. Build. Mater., 327, 10, 10.1016/j.conbuildmat.2022.127006 · DOI
  58. Zhang, 2018, Rheology, agglomerate structure, and particle shape of fresh geopolymer pastes with different NaOH activators content, Constr. Build. Mater., 187, 674, 10.1016/j.conbuildmat.2018.07.205 · DOI
  59. Medri, 2020, Metakaolin-based geopolymer beads: production methods and characterization, J. Clean. Prod., 244, 9, 10.1016/j.jclepro.2019.118844 · DOI
  60. Xu, 2022, Mechanical and microscopic properties of fiber-reinforced coal gangue-based geopolymer concrete, Nanotechnol. Rev., 11, 526, 10.1515/ntrev-2022-0033 · DOI
  61. Qin, 2020, Effect of Ca/Si atio on the formation and characteristics of synthetic aluminosilicate hydrate gels, Mater. Rep., 34, 12057
  62. Kissling, 2021, Influence of low-pressure treatment on the morphological and compositional stability of microscopic ettringite, Materials, 14, 17, 10.3390/ma14112720 · DOI
  63. Binici, 2012, The sulphate resistance of cements containing red brick dust and ground basaltic pumice with sub-microscopic evidence of intra-pore gypsum and ettringite as strengtheners, Cem. Concr. Compos., 34, 279, 10.1016/j.cemconcomp.2011.10.001 · DOI
  64. Kan, 2019, Hydration kinetics of municipal solid wastes incineration (MSWI) fly ash-cement, J. Wuhan. Univ. Technol. -Mat. Sci. Ed., 34, 596, 10.1007/s11595-019-2093-z · DOI
  65. Luo, 2022, Co-disposal of MSWI fly ash and lead-zinc smelting slag through alkali-activation technology, Constr. Build. Mater., 327, 10, 10.1016/j.conbuildmat.2022.127006 · DOI
  66. Qin, 2020, Effect of Ca/Si atio on the formation and characteristics of synthetic aluminosilicate hydrate gels, Mater. Rep., 34, 12057
  67. Zhou, 2017, Influence of Ca/Si ratio of concrete pore solution on thaumasite formation, Constr. Build. Mater., 153, 261, 10.1016/j.conbuildmat.2017.07.104 · DOI
  68. Li, 2019, Effects of Ca/Si ratio, aluminum and magnesium on the carbonation behavior of calcium silicate hydrate, Materials, 12, 14, 10.3390/ma12081268 · DOI
  69. 2008, State administration of quality supervision, Insp. Quar., 15
  70. Djedidi, 2009, Metals removal from soil, fly ash and sewage sludge leachates by precipitation and dewatering properties of the generated sludge, J. Hazard. Mater., 1372, 10.1016/j.jhazmat.2009.07.144 · DOI
  71. Ei-Eswed, 2017, Efficiency and mechanism of stabilization/solidification of Pb(II), Cd(II), Cu(II), Th(IV) and U(VI) in metakaolin based geopolymers, Appl. Clay Sci., 140, 148, 10.1016/j.clay.2017.02.003 · DOI
  72. Luo, 2022, Co-disposal of MSWI fly ash and lead-zinc smelting slag through alkali-activation technology, Constr. Build. Mater., 327, 10, 10.1016/j.conbuildmat.2022.127006 · DOI
  73. Izquierdo, 2010, The role of open and closed curing conditions on the leaching properties of fly ash-slag-based geopolymers, J. Hazard. Mater., 176, 623, 10.1016/j.jhazmat.2009.11.075 · DOI
  74. Lan, 2022, Synthesis and application of geopolymers from municipal waste incineration fly ash (MSWI FA) as raw ingredient-a review, Resour. Conserv. Recycl., 182, 16, 10.1016/j.resconrec.2022.106308 · DOI
  75. El-Eswed, 2015, Stabilization/solidification of heavy metals in kaolin/zeolite based geopolymers, Int. J. Miner. Process., 137, 34, 10.1016/j.minpro.2015.03.002 · DOI
  76. Chen, 2022, Mechanochemically incorporating magnesium sulfate into antigorite to provide active nucleation sites for efficient precipitation of cadmium ions from weak acidic solution, J. Hazard. Mater., 424, 11, 10.1016/j.jhazmat.2021.127272 · DOI

Metadata

Authors
Feng, D., Wang, J., Wang, Y., & Liang, S.
Affiliations
Guangdong University of Technology (CN)
Venue
Case Studies in Construction Materials
Publisher
Elsevier BV
Published
2023-12
Volume
19
Pages
e02417
ISSN
2214-5095 (ISSN-L)
OpenAlex
W4386072721
Cited by
26
References
1
Citations by year
2026: 2 · 2025: 11 · 2024: 10 · 2023: 3
FWCI
2.80
Type
journal article
Language
en
Open access
Locations
  • Case Studies in Construction Materials (publishedVersion, cc-by-nc-nd)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Funders
  • Guangzhou Municipal Science and Technology Program key projects (202002030194)
  • National Natural Science Foundation of China-Guangdong Joint Fund (2022A1515011047)
  • National Natural Science Foundation of China (52078142)
  • Natural Science Foundation of Guangdong Province
Topics
  • Physical Sciences › Engineering › Civil and Structural Engineering › Concrete and Cement Materials Research
  • Physical Sciences › Engineering › Building and Construction › Recycling and utilization of industrial and municipal waste in materials production
  • Physical Sciences › Engineering › Civil and Structural Engineering › Geotechnical Engineering and Soil Stabilization
Keywords
municipal solid waste incineration bottom ash, heavy metal immobilization, unconfined compressive strength, water stability, heavy metal leaching, thermal stability, microstructure, mineral composition

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Experimental study on solidification/stabilisation of high-salt sludge by alkali-activated GGBS and MSWI bottom ash cementitious materials. https://app.cochat.ai/papers/10.1016/j.cscm.2023.e02417
The paper
Feng, D., Wang, J., Wang, Y., & Liang, S. (2023). Experimental study on solidification/stabilisation of high-salt sludge by alkali-activated GGBS and MSWI bottom ash cementitious materials. Case Studies in Construction Materials. https://doi.org/10.1016/j.cscm.2023.e02417