The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Engineering stable electrode-separator interfaces with ultrathin conductive polymer layer for high-energy-density Li-S batteries
Abstract
Abstract Lithium-sulfur (Li-S) battery has been regarded as a promising energy-storage system due to its high theoretical specific capacity of 1675 mAh g−1 and low cost of raw materials. However, several challenges remain to make Li-S batteries viable, including the shuttling of soluble lithium polysulfide intermediates and pulverization of Li metal anode. Engineering stable electrode-separator interfaces without causing large mass/volume increase of inactive materials and electrolyte uptake is an effective approach to improve the cycling stability of Li-S batteries while maintaining high available energy density. Herein, we report the engineering of a stable electrode-separator interface with an ultrathin conductive polymer nanolayer on the pore walls of both surfaces of the separator via a simple and scalable approach using in-situ vapor-phase polymerization of polypyrrole (PPy) on commercial Celgard separator with only a small increase in overall mass and volume. The inherent hydrophilicity of PPy enables the separator to have enhanced electrolyte uptake, which facilitates homogenous Li+ flux and thus uniform plating and stripping of metallic lithium at the anode side during the charge/discharge processes. Meanwhile, the chemical immobilization effect of PPy suppresses the migration of the soluble polysulfides and improves the stability of the sulfur cathode. We showed that a Li||Li symmetrical cell with the PPy modified separator gave a low and stable overpotential of less than 30 mV for over 250 h' stripping and plating test at 1 mA cm−2 with a fixed areal capacity of 3 mAh cm−2, which was significantly better than that using a regular Celgard separator. Using the PPy modified separator, Li-S cell with sulfur/carbon black composite cathode and lithium anode delivered stable cycling for 250 cycles at 0.5 C with a low capacity decay rate of 0.083% per cycle. Even for a Li-S cell with a high-areal-capacity sulfur cathode (4.8 mAh cm−2), good cycling stability was achieved. It gave a reversible areal capacity of 3.6 mAh cm−2 after 150 charge/discharge cycles at 0.2 C with 75.6% capacity retention. Besides, the as-achieved separator showed better thermal stability than the bare counterpart. This work offers an alternative approach for achieving a practical Li-S battery toward high energy density and long cycle life through simple and scalable separator-electrode interface engineering without significant increase in volume and mass.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Reviving the lithium metal anode for high-energy batteries
Lin, D., Liu, Y., & Cui, Y. (2017) · Nature Nanotechnology · doi:10.1038/nnano.2017.16 · Cited by 6,763
Lee, H., Lim, H.-S., Ren, X., Yu, L., Engelhard, M. H., Han, K. S., Lee, J., Kim, H.-T., Xiao, J., Liu, J., et al. (2018) · ACS Energy Letters · doi:10.1021/acsenergylett.8b01819 · Cited by 150
Cited by
Towards practical lithium-metal anodes
Zhang, X., Yang, Y., & Zhou, Z. (2020) · Chemical Society Reviews · doi:10.1039/c9cs00838a · Cited by 726
Recent progress of separators in lithium-sulfur batteries
Li, C., Liu, R., Xiao, Y., Cao, F., & Zhang, H. (2021) · Energy Storage Materials · doi:10.1016/j.ensm.2021.05.034 · Cited by 343
Yao, W., Xu, J., Ma, L., Lu, X., Luo, D., Qian, J., Zhan, L., Manke, I., Yang, C., Adelhelm, P., et al. (2023) · Advanced Materials · doi:10.1002/adma.202212116 · Cited by 317
Hao, H., Hutter, T., Boyce, B. L., Watt, J., Liu, P., & Mitlin, D. (2022) · Chemical Reviews · doi:10.1021/acs.chemrev.1c00838 · Cited by 314
Mechanistic understanding of the role separators playing in advanced lithium‐sulfur batteries
Wei, Z., Ren, Y., Sokolowski, J., Zhu, X., & Wu, G. (2020) · InfoMat · doi:10.1002/inf2.12097 · Cited by 302
Metadata
- Authors
- Li, Y., Wang, W., Liu, X., Mao, E., Wang, M., Li, G., Fu, L., Li, Z., Eng, A. Y. S., Seh, Z. W., & Sun, Y.
- Venue
- Energy Storage Materials
- Publisher
- Elsevier BV
- Published
- 2019-12
- Volume
- 23
- Pages
- 261-268
- ISSN
- 2405-8289 (ISSN-L)
- 2405-8297
- OpenAlex
- W2943878428
- Cited by
- 193
- References
- 2
- FWCI
- 10.93
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Engineering stable electrode-separator interfaces with ultrathin conductive polymer layer for high-energy-density Li-S batteries. https://app.cochat.ai/papers/10.1016/j.ensm.2019.05.005
- The paper
- Li, Y., Wang, W., Liu, X., Mao, E., Wang, M., Li, G., Fu, L., Li, Z., Eng, A. Y. S., Seh, Z. W., & Sun, Y. (2019). Engineering stable electrode-separator interfaces with ultrathin conductive polymer layer for high-energy-density Li-S batteries. Energy Storage Materials. https://doi.org/10.1016/j.ensm.2019.05.005
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.