The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Extrusion-based 3D printing of food pastes: Correlating rheological properties with printing behaviour
Open accessAbstract
Development of 3D food printing applications requires in-depth knowledge on printing behaviour of food materials. In extrusion-based 3D printing, rheological properties of a recipe are critical to achieve successful printing. The objective of this research is to investigate potential correlations between printability of formulations and simple rheological properties. We used tomato paste as a model system to investigate the correlation between printing stability, dispensability and rheological properties. The results show a linear correlation between ingredient's flow stress, zero shear viscosity and corresponding printing stability. The extrusion pressure necessary to extrude tomato paste increased linearly with increasing flow stress. More experiments with other aqueous-based food formulations indicated that their printability aligned reasonably well with the correlation of tomato paste; however, for fat-based products different printing behaviour was observed. Finally, we propose a rational guideline for developing aqueous food recipes with desired printability based on flow stress measured by shear rheology.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3D printing: Printing precision and application in food sector
Liu, Z., Zhang, M., Bhandari, B., & Wang, Y. (2017) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2017.08.018 · Cited by 858
Guo, C.-F., Zhang, M., & Bhandari, B. (2019) · Computers and Electronics in Agriculture · doi:10.1016/j.compag.2019.04.032 · Cited by 118
Cited by
Direct Ink Writing: A 3D Printing Technology for Diverse Materials
Saadi, M. A. S. R., Maguire, A., Pottackal, N. T., Thakur, M. S. H., Ikram, M. M., Hart, A. J., Ajayan, P. M., & Rahman, M. M. (2022) · Advanced Materials · doi:10.1002/adma.202108855 · Cited by 1,335
Seoane-Viaño, I., Januskaite, P., Alvarez-Lorenzo, C., Basit, A. W., & Goyanes, A. (2021) · Journal of Controlled Release · doi:10.1016/j.jconrel.2021.02.027 · Cited by 357
Recent advances and future perspective in additive manufacturing of foods based on 3D printing
Le-Bail, A., Maniglia, B. C., & Le-Bail, P. (2020) · Current Opinion in Food Science · doi:10.1016/j.cofs.2020.01.009 · Cited by 229
3D printing to innovate biopolymer materials for demanding applications: A review
Li, N., Qiao, D., Zhao, S., Lin, Q., Zhang, B., & Xie, F. (2021) · Materials Today Chemistry · doi:10.1016/j.mtchem.2021.100459 · Cited by 142
Outrequin, T. C. R., Gamonpilas, C., Siriwatwechakul, W., & Sreearunothai, P. (2023) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2022.111371 · Cited by 113
Metadata
- Authors
- Zhu, S., Stieger, M. A., van der Goot, A. J., & Schutyser, M. A. I.
- Venue
- Innovative Food Science & Emerging Technologies
- Publisher
- Elsevier BV
- Published
- 2019-12
- Volume
- 58
- Pages
- 102214
- ISSN
- 1466-8564 (ISSN-L)
- OpenAlex
- W2969557401
- Cited by
- 250
- References
- 2
- FWCI
- 11.10
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Extrusion-based 3D printing of food pastes: Correlating rheological properties with printing behaviour. https://app.cochat.ai/papers/10.1016/j.ifset.2019.102214
- The paper
- Zhu, S., Stieger, M. A., van der Goot, A. J., & Schutyser, M. A. I. (2019). Extrusion-based 3D printing of food pastes: Correlating rheological properties with printing behaviour. Innovative Food Science & Emerging Technologies. https://doi.org/10.1016/j.ifset.2019.102214
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.