An improved transient plane source technique and methodology for measuring the thermal properties of anisotropic materials
Integrity signals
Registry
Cites
Statistics
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
Error in TPS measurement comes from two sources: (1) uncertainty in experimental data and selection of time interval for analysis, and (2) deviation of the original idealized analytical heat transfer model from the practical measurement scenario.
“Error in the TPS measurement 20-31 comes from two sources: (1) uncertainty in the experimental data and the selection of time interval for analysis, and (2) deviation of the original idealized analytical heat transfer model 3, 32 from the practical measurement scenario.”
From Analysis and improvement of the hot disk transient plane source method for low thermal conductivity materials (2020) · cites this paper as [29]
The bifilar spiral metal heater together with the dielectric insulation layer are usually approximated by several concentric and equally spaced circular rings with constant power in both analytical and numerical prior models.
“The bifilar spiral metal heater together with the dielectric insulation layer are usually approximated by several concentric and equally spaced circular rings with constant power in both analytical 3, 32 and numerical 20, 27-31 prior models.”
From Analysis and improvement of the hot disk transient plane source method for low thermal conductivity materials (2020) · cites this paper as [29]
Several publications investigated the accuracy and performance of commercial TPS devices based on numerical simulations to study the effect of sensors on TPS measurement for bulk or thin film and the error due to thermal radiation in semitransparent sample.
“In the latter aspect, several publications investigated the accuracy and performance of commercial TPS devices based on numerical simulations to study the effect of the sensors on the TPS measurement for bulk or thin film 20, 27-31 and the error due to thermal radiation in semitransparent sample. 17, 33”
From Analysis and improvement of the hot disk transient plane source method for low thermal conductivity materials (2020) · cites this paper as [29]
Cites
Thermal conductivity measurement from 30 to 750 K: the 3ω method
Cahill, D. G. (1990) · Review of Scientific Instruments · doi:10.1063/1.1141498 · Cited by 1,928 · see citing works
Theoretical accuracy of anisotropic thermal conductivity determined by transient plane source method
Zhang, H., Li, Y.-M., & Tao, W.-Q. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.01.025 · Cited by 69 · see citing works
Flagged first, then by citations
Cited by
Sorted by citations
Zheng, Q., Kaur, S., Dames, C., & Prasher, R. S. (2020) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2020.119331 · Cited by 162 · see citing works
“However, detailed information about the specific fitting and optimization procedure is rarely given in the literature, being typically either described simply as a least square method (often without specifying the fitting parameters) 27, 28 or not clearly mentioned.(29) This details of this step were only mentioned in…”
Method
- Authors
- Elkholy, A., Sadek, H., & Kempers, R.
- Affiliations
- York University (CA)
- Corresponding author
- Kempers, Roger
- Venue
- International Journal of Thermal Sciences
- Publisher
- Elsevier BV
- Published
- 2019-01
- Volume
- 135
- Pages
- 362-374
- ISSN
- 1290-0729 (ISSN-L)
- OpenAlex
- W2895367956
- Cited by
- 55
- References
- 2
- Citations by year
- 2026: 5 · 2025: 12 · 2024: 11 · 2023: 7 · 2022: 6 · 2021: 7 · 2020: 6 · 2019: 1
- FWCI
- 1.31
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- International Journal of Thermal Sciences (publishedVersion)
- Topics
- Physical Sciences › Materials Science › Materials Chemistry › Thermal properties of materials
- Physical Sciences › Engineering › Mechanics of Materials › Thermography and Photoacoustic Techniques
- Physical Sciences › Engineering › Mechanical Engineering › Mechanical and Thermal Properties Analysis
- Keywords
- transient plane source technique, anisotropic materials, thermal conductivity ratio, heat capacity, heater power, measurement error analysis
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
